Table of Contents
Advertisement
Quick Links
TYPHOON
L50B Pro
opErAting instructions
Please keep for future reference
Thank you for purchasing this Typhoon L50B Pro charger. We are sure you will be pleased
with its performance and features. In order to ensure that you obtain the maximum benefit
from its operation, please read these instructions carefully.
Advertisement
Table of Contents
Related Manuals for Fusion TYPHOON L50B PRO
Summary of Contents for Fusion TYPHOON L50B PRO
-
Page 1: Operating Instructions
Please keep for future reference Thank you for purchasing this Typhoon L50B Pro charger. We are sure you will be pleased with its performance and features. In order to ensure that you obtain the maximum benefit from its operation, please read these instructions carefully. -
Page 3: Specifications
SpEciFicAtions Input Voltage Battery Type & Cells Battery Capacity Charge Rate Trickle Charge Rate Balancing Charge Termination Delta Peak Sensitivity SpECIAL FEATUrES • 2 -line, 16 character, blue backlit, LCD makes the screen extremely clear and legible. • Built-in intelligent balancing circuit is designed to individually balance each cell on the connected lithium battery pack within the tolerance of 5mV during charge or discharge. -
Page 4: Safety Precautions
• This unit is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use it safely. • Young children should be supervised to ensure that they do not play with the Typhoon L50B Pro. • DO NOT attempt to charge non-rechargeable batteries. • The battery must be placed in a well ventilated area (for charging lead- acid batteries) • After charging, disconnect the battery charger from the power supply... -
Page 5: Lithium Ion/Polymer Battery Safety Warnings
Lithium Ion/polymEr BAttEry SAFEty WArnings Ensure that the charger and battery are placed on a non-flammable surface whilst charging and ideally charge outdoors wherever possible. NEVER charge a Lithium ION/Polymer/Fe battery inside a vehicle whatever the circumstances. ALWAYS ensure that the charger is correctly set for the battery being charged, checking both voltage and capacity. - Page 6 Lithium Ion/polymEr/FE BAttEriEs Lithium battery packs must NEVER be discharged below 3 volts per cell as this will result in damage to the cells. If the voltage is allowed to drop below 3 volts per cell the battery voltage may seem to recover following a charge, but the battery may not then give its full nominal capacity and a reduction in performance is likely –...
-
Page 7: Input Power
Input powEr 12V DC Connect the charger’s red alligator clip to the positive (+) terminal on the power source and the black alligator clip to the negative (-) terminal. The charger will display “Input voltage” error message if the input is below 11V or above 15V. - Page 8 • When the charger is connected to the power source the charger will show the battery mode that was last used. • If the battery TYPE button is briefly pressed, the present battery type (NiCd, NiMH, Lithium, or Pb ) will flash. While the existing battery type is flashing, every time the battery TYPE button is pressed, the following modes are shown in order: BATT TYPE NiMH CHARGE NiCd CHARGE...
- Page 9 • If the other buttons are pressed, or nothing is pressed, the present battery type stops flashing. • If the Battery TYPE button is pressed and briefly held, the recent & previous data will be shown until the Battery TYPE button is pressed. • If the ENTER button is briefly pressed, a parameter which can be adjusted starts to flash and if the ENTER button is pressed again, the next parameter starts to flash.
- Page 10 Lithium Modes (Li-Ion/Li-Po/Li-Fe) BATT TYPE BALANCER CON. NOT CONNECTED This charger is capable of charging up to 6 cell Lithium-Ion, Lithium-Polymer or LiFePO4 batteries. It uses “constant current / constant voltage” regime in order to fully charge these Lithium batteries. Constant current is delivered during the fast charge.
- Page 11 Setting Battery Voltages For Li-Po Battery Pack LiPo CHARGE 3.0A Select the correct total battery voltage to be charged with C=3000mAh 11.1Vp the INC & DEC buttons – 3.7V, 7.4V, 11.1V, 14.8V and 18.5V [Vpack]. Setting Battery Voltages For Li-Fe Battery Pack LiFe CHARGE 3.0A Select the correct total battery voltage to be charged with the C=3000mAh 11.1Vp...
- Page 12 Pb Mode BATT TYPE to NiCd charge Setting Charge Current PB CHARGE Adjust the desired charge current, which ranges from 0.1A to C=3.0A 12Vpack 6.0A with the INC & DEC buttons. Press the ENTER button to confirm the setting. Setting Battery Voltages For a Lead-Acid (Pb) PB CHARGE Battery Pack C=3.0A 12Vpack...
-
Page 13: Screen Displays
Displays During Charge “BLC” will be shown if the balancer cable of the battery is connected to the balancing port of the charger. CHG 0.30:25 00000 CHG: Charge NC + 3.00A 5.200V NC = NiCd NM = NiMH Ll = Lilo, LP = LiPo, LF = LiFe Pb = Pb Completion Display (with Audible Warning) END 030:00 00000... -
Page 14: Error Messages
Error mEssAgEs Input voltage is below 11.0V or exceeds 15V. INPUT BATTERY VOLTAGE ERROR Battery is not connected to the charger’s output banana NO BATTERY sockets. Battery is connected to the output banana sockets in OUTPUT BATTERY reverse. REVERSE POLARITY The circuit of the charger has a problem. - Page 16 www. ogic .com Logic RC Limited 14 Hartham Lane Herford SG14 1QN United Kingdom...