Page 1
Support high quality audio include 2 internal high power speaker d. Fully Support ACPI 1.0, meet PC98/PC99 requirement e. Built-in 56K modem for Data/Fax/Voice modem or Internet (optional) f. Support high performance hardware 2D/3D graphic engine 340S8 Rev : A Page...
Page 2
Provides interface to Low Pin Count (LPC) operating at 33MHz clocks which is the same as the PCI clock on the Host. Built-in fast PCI-IDE controller supports the ATA PIO/DMA and ultraDMA33/66/100 functions that supports the data transfer rate up to 100 MB/s 340S8 Rev : A Page...
Page 3
2 click buttons, Lithium-ION battery pack, and AC adapter. The system board incorporates CPU module, system memory, system and VGA BIOS, audio controller, CPU/ PCI bus controller, PCI / ISA bus controller. The 340S8 Rev : A Page...
Page 4
System Block Diagram shows how these components are integrated as shown in the next page. Sock DIMM DS90C DIMM F363A Host Bus DSTN CS9211 Core Logic LM483 Alc 200 SIS 630S SMBu RTL820 PCMCI SLOT Cpu_core,+1.8 V,+2.5V,Vcc_c OZ6812 POWE Moden 340S8 Rev : A Page Conn.
Page 5
KBVCCA : KBC AD/DA 3.3V reference voltage RTCVDD : Real time clock power source +5V_AUX : LAN 5V always power source +3V_AUX : LAN 3.3V always power source & KBC 3.3V power Source +3V_RX_TR : LAN 3.3V analog power source 340S8 Rev : A Page...
Page 6
: 3mA rms – 5.5mA rms Protection : Open circuit protect, current limit protect 1.2.8 Battery Pack A. Lithium – Ion Battery packs Battery type : Li-Ion Battery cells : 8 cells Battery Spec : 3.7V / 1800mAH 340S8 Rev : A Page...
Page 7
1.2.10 Interrupt Request Channel Setting Hardware using the setting System timer Standard 101/102-Key Microsoft Natural Keyboard Programmable Interrupt Controller IrDA V3.0 Fast Infrared Port Communications Port (Com1) Standard Floppy Disk Controller ECP Printer Port (LPT1) 340S8 Rev : A Page...
Page 8
When ‘Battery Very Low Warning’ occurs, the Power LED will flash at a rate of 1 time every 4 seconds if there is no ‘Suspend to Disk’ partition in the hard disk. Charge (flash/off): Will be flashing when the battery pack is being charged. 340S8 Rev : A Page...
Page 9
Brightness down Fn + F9 (SMI) Contrast up (for DSTN LCD) Fn + F10 (SMI) Contrast down(for DSTN LCD) UNIWILL COMPUTER CORP. No.24, Pei Yuan Rd., Chung Li Industrial Park Chung Li City, Taiwan, R.O.C. TEL: 886-3-461-6000 FAX: 886-3-461-6317 URL: http:// www.uniwill.com.tw/...
“Cover Switch” setting in the BIOS Setup menu. 2.2.3 Quick Start Button When this button has been pressed, the system will launch either Microsoft Internet Explorer, E-Support or E-mail/User Defines etc. 3 quick buttons demands. 2.3. Major Components and Connectors Location 340S8 Rev : A Page...
Page 22
Chapter 5 Troubleshooting Guidelines UNIWILL COMPUTER CORP. No. 24, Pei Yuan Rd., Chung Li Industrial Park Chung Li City, Taiwan, R.O.C. TEL: 886-3-461-6000 FAX: 886-3-461-6317 URL: http://www.uniwill.com.tw/ 340S8 Rev : A Page...
Page 23
IC 74HCT 4066D PHILIPS 07-U21031-00 IC BA9743AFV 16P 08-U90013-00 IC LM78L12AC SOIL 8P 08-U10008-00 IC MB3878 24 PIN 08-C38780-40 IC TL594CD PWM CONTROL SO-16 08-159400-40 IC PACS1284-020 /T QSOP28 08-U90009-00 3.2 Major Components Pin Assignment 340S8 Rev : A Page...
Page 40
Chapter 5 Troubleshooting Guidelines System Disassembly Procedure 340S8 Rev : A Page...
Page 41
4. Disconnect the cable CPU fan + heat sink assembly from the mainboard. 5. Gently press down the lever arm of the CPU socket and lift it up until the lever arm is in stand position. 340S8 Rev : A Page...
Page 42
6. Make sure the CPU socket is in release position before you remove the CPU. 7. Unfasten one (1) screw on the HDD cover. 8. Unfasten two (2) screws on the HDD metal bracket. 9. Pull out the HDD assembly and disconnect the HDD cable from the mainboard. 340S8 Rev : A Page...
Page 43
10. Use a small flat screwdriver , insert to the K/B lock to release the three lock. 11. Gently lift the keyboard and disconnect the keyboard cable from the connector. 12. Remove the keyboard shielding or plate. 340S8 Rev : A Page...
Page 44
15. Close the display panel, press down the middle cover and then pull out to remove. 16. Unfasten one screws of the CD-ROM ( or DVD-ROM drive). 17. On the bottom case, push out the CD-ROM drive as shown in the photo. 340S8 Rev : A Page...
Page 45
20. After releasing the snap lock on both side and palm rest. Lift up to release and remove the top cabinet. 21. Close the display panel and unfasten four (4) screws on both sides of the display hinges. 340S8 Rev : A Page...
Page 46
22. Unfasten one (1) screw on the LCD cable and disconnect the two LCD cables from the mainboard connectors. 23. Unfasten two (2) screws on the hinge frame as shown in the photo. 24. Disconnect the FDD cable. 25. Disconnect the Touchpad cable. 340S8 Rev : A Page...
Page 47
29. On the bottom side of the mainboard, unfasten four (4) screws on the mainboard shielding and peel off the aluminum foil near the I/O port as shown in the picture. 30. From the I/O port, unfasten six (6) hexagonal screws on the I/O ports. 340S8 Rev : A Page...
Page 48
33. When replacing mainboard, make sure to have all the insulation and thermal pads removed from the defective mainboard and transfer it to a good mainboard ( because sometimes, the good mainboard doesn’t have all the tapes and thermal pad as indicated in the photo). 340S8 Rev : A Page...
Page 49
Chapter 5 Troubleshooting Guidelines 34. Unfasten one (1) screw on the FDD assembly. Lift to remove the FDD assembly form the bottom case. 340S8 Rev : A Page...
Page 51
3. Unfasten four (4) screws on the LCD display and unfasten four (4) screws on both side of the hinges. Remove the LCD from the display cover. Make sure to remember the LCD cable arrangement to avoid problem when assembling the LCD display. 340S8 Rev : A Page...
Page 52
Chapter 5 Troubleshooting Guidelines UNIWILL COMPUTER CORP. No. 24, Pei Yuan Rd., Chung Li Industrial Park Chung Li City, Taiwan, R.O.C. TEL: 886-3-461-6000 FAX: 886-3-461-8000 URL: http://uniwill.com.tw/ 340S8 Rev : A Page...
Page 53
5.12 PIO port test error 5.13 Audio failure 5.14 No power symptom 5.15 CDROM drive test error 5.16 Stopping in LCD screen while booting 5.17 PCMCIA Card Bus failure 5.18 IR Port cannot transfer data 5.19 Modem Failure 340S8 Rev : A Page...
Page 54
Display ok M/B one at a time to find out which part is causing the problem Replace motherboard Board level troubleshooting Check SIS Chipset for Re-solder any cold solder? Check system clock and reset circuit 340S8 Rev : A Page...
Page 55
Remove all of I/O devices and cables from M/B except LCD or Monitor Display OK Connect the I/O device & cables to the M/B one per time to find out which part is causing the problem Replace Motherboard 340S8 Rev : A Page Board level troubleshooting...
Page 56
Symptom: The LCD shows nothing or abnormal picture, but it is ok for external monitor. LCD No Display Try another known good LCD module Replace each parts of LCD Display module / cables and test 340S8 Rev : A Page...
Page 58
Symptom: The CRT monitor shows nothing or abnormal color, but it is ok for Monitor No Display Try another known good monitor Display Ok? Replace faulty monitor Setup Ok? Correct it Replace motherboard Board level Troubleshooting Check VGA port signal using oscilloscope Replace SIS 630 Chipset 340S8 Rev : A Page...
Page 59
5.5 Memory test error Memory test error With External DRAM Module Installed? Install External Correct it DRAM module and socket OK? Try another known good DRAM module Replace the Test OK? faulty DRAM module Replace motherboard 340S8 Rev : A Page...
Page 60
Replace the faulty keyboard Replace motherboard Board level troubleshooting Re-soldering Check for cold solder? One of the following parts or signals on the other board may be defective, use an oscilloscope to check 1.K/B Controller PC87570 340S8 Rev : A Page...
Page 61
Board level troubleshooting Check KB controller Re-solder PC87570 for cold solder? Check one of the following parts or signals on the motherboard maybe defective, use an oscilloscope and replace it. 1. KB Controller – PC87570 340S8 Rev : A Page...
Page 62
2. Check setup for correct settings Correct it Reboot OK? Try another known good FDD module Correct it Reboot OK? Replace motherboard Board level troubleshooting Check FDD connector, Super I/O controller Re-solder PC87393 for cold solder? 340S8 Rev : A Page...
Page 63
Symptom: Either an error message is shown, or the drive motor spins non-stop, while reading data from or writing data to Hard disk Hard disk test error Check BIOS Correct it HDD Setup OK? Try another working HDD 340S8 Rev : A Page Replace the faulty parts Re-boot ok?
Page 64
Chapter 5 Troubleshooting Guidelines 5.10 CMOS test error 340S8 Rev : A Page...
Page 65
Check CMOS RAM, Re-solder CMOS battery for cold solders One of the following parts on the motherboard maybe defective, replace the parts one a time and test after each replacement: 1.CMOS RAM 2. CMOS battery 340S8 Rev : A Page...
Page 66
Board level troubleshooting Check SIO Re-solder controller for cold solder? One of the following parts on the motherboard maybe defective, plug SIO loopback at SIO port and run SIO test program. If error, replace SIO controller 340S8 Rev : A Page...
Page 68
Board level troubleshooting Check PIO Re-solder controller, for cold solder? One of the following parts on the motherboard maybe defective, plug PIO loopback at PIO port one a time and test, if error replace PIO controller 340S8 Rev : A Page...
Page 69
Re-test ok? Correct it Setup ok? Correct it Replace motherboard Board-level troubleshooting Check SIS 630 Chipset for cold Re-soldering Solder One of the following parts on the motherboard may be defective, replace the audio controller chip 340S8 Rev : A Page...
Page 70
No Power Check Fuse on DC/DC Replace it Board if open Check DC/DC Board Signal or replace each Correct it parts. Press Power on button again Check system LED lit on 340S8 Rev : A Page...
Page 71
Replace Motherboard Board Level Troubleshooting Check SIS 630 Chipset and CDROM connector Re-soldering for cold solder? Check one of the following parts or signal on the M/B may be defective, use an oscilloscope to check it. 340S8 Rev : A Page...
Page 72
Stop in LCD screen while booting Check one of the following parts or signal on the M/B may be defective, use an oscilloscope to check it. Check CPU & SIS630 for cold Re-soldering soldering? OK? 340S8 Rev : A Page...
Page 73
Check drive & Correct it controller install OK? Board-level Trouble shooting Check PCMCIA slot Re-soldering mounting in M/B is cold soldering Check O2Micro OZ Re-solder 6812 Chipset for cold soldering? Replace O2Micro OZ6812 chipset 340S8 Rev : A Page...
Page 74
Correct it Check driver install OK Correct it Check another one IR Try another IR device is meet IrDa 1.0 device Board-level trouble shooting Check PC87393 for cold Re-soldering soldering Replace Super I/O PC97393 Chipset 340S8 Rev : A Page...
Page 75
AT command test Re-install Drivers modem function is OK Board-level trouble shooting Check modem DAA board is connected properly and Connect it wiring with the phone jack Replace another known good modem DAA module. 340S8 Rev : A Page 75...
Page 76
UNIWILL COMPUTER CORP. No. 24, Pei Yuan Rd., Chung Li Industrial Park, Chung Li City, Taiwan, R.O.C. TEL: 886-3-461-6000 FAX: 886-3-461-6317 URL: http://www.uniwill.com.tw/ 340S8 Rev : A Page 76...
Page 77
When system is powered ON : 1A Ni-MH Vendor : PANASONIC, TOSHIBA Battery Type : Ni-MH, 10 cells (10S) Battery Capacity : 12.0V, 4500mAh (54.0 watts) Charge voltage : 16.8V +2.5% -1.0% Charge temperature : 0~45 340S8 Rev : A Page 77...
Page 78
Group III fax / telephony answering machine / DTMF generation and detection Local handset, telephone and microphone record / telephone line and headset or Peaked playback / VOX voice Detection/ Caller ID (optional) / host base DSVD 340S8 Rev : A Page 78...
Page 79
UNIWILL COMPUTER CORP. No. 24, Pei Yuan Rd., Chung Li Indistrial Park Chung Li City, Taiwan,R.O.C. TEL: 886-3-461-6000 FAX: 886-3-461-6317 URL: http:// uniwill.com.tw/ 340S8 Rev : A Page 79...
Page 80
40-102901-00 SPRING FOR K/B 340 41-720120-04 M2.0*4 50-312903-10 TOP HOUSING (MG) 340 41-720120-03 M2.0*3 22-300513-10 SPK FG-36N081 50-352967-00 COVER HINGE (R ) 340 50-352966-00 COVER HINGE FRAME 41-720120-03 M2.0*3 50-352969-00 COVER CABLE FOR 340 340S8 Rev : A Page 80...
Page 81
MYLAR HDD 340 40-U75071-00 PLATE HDD 340 41-760230-03 SCREW M3.0*3 41-720120-04 SCREW M2.0*4 50-U69064-20 DOOR HDD 340 41-720120-04 SCREW M2.0*4 29U6905B-00 CABLE HDD 340 RUBBER FOOT 340 50-U69063-20 DOOR CPU 340 SCREW M2.5*4.5 PAN 340S8 Rev : A Page 81...