6ohms:
Select if the impedances of all speakers are
between 6 and 16 ohms.
Note
• (North American models) Speakers with an impedance of
less than 6 ohms are not supported.
■
Speakers Type (Front)
Normal:
Select this if you've connected your front
speakers normally.
Bi-Amp:
Select this if you've bi-amped your front
speakers.
■
Powered Zone 2
No
Yes:
Zone 2 speakers can be used (Powered Zone 2
enabled).
Note
• If the "Speakers Type (Front)" setting is set to "Bi-Amp",
Powered Zone 2 cannot be used.
• When the "Powered Zone 2" setting is set to "Yes" and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
Speaker Configuration
This setting is set automatically by
Audyssey MultEQ
®
Room Correction and Speaker
Setup function (➔ page 23).
With these settings, you can specify which speakers
are connected and a crossover frequency for each
speaker. Specify "Full Band" for speakers that can
output low frequency bass sounds adequately, for
example, speakers with a good sized woofer. For
smaller speakers, specify a crossover frequency.
Sounds below the crossover frequency will be output
by the subwoofer instead of the speaker. Refer to
your speaker's manuals to determine the optimum
crossover frequencies.
■
Subwoofer
Yes
No
■
Front
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz,
200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting
is fixed at "Full Band".
■
Center
, Surround
*1
*1
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz,
200Hz
None
■
Front High
*1*2*3*5
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz,
200Hz
None
■
Surround Back
*1*2*3*4
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz,
200Hz
None
Note
*1
"Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
En-54
Advanced Operations
*2
If the "Surround" setting is set to "None", this setting
cannot be selected.
*3
If the "Speakers Type (Front)" setting is set to
"Bi-Amp", or the "Powered Zone 2" setting is set to
"Yes" together with Zone 2 turned on, this setting cannot
be selected.
*4
If anything else than "None" is selected in "Front High",
this setting is automatically set to "None".
*5
If anything else than "None" is selected in "Surround
Back", this setting is automatically set to "None".
■
Surround Back Ch
1ch:
Select if only one surround back speaker L is
connected.
2ch:
Select if two (left and right) surround back
speakers are connected.
Note
• If the "Surround Back" setting is set to "None", this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz, 90Hz, 100Hz, 110Hz, 120Hz
Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff
frequency of the LFE channel's low-pass filter
(LPF), which can be used to filter out unwanted
hum. The LPF only applies to sources that use the
LFE channel.
■
Double Bass
This setting is NOT set automatically by
Audyssey MultEQ Room Correction and Speaker
Setup function (➔ page 23).
Operating
procedure
(➔ page 50)