Set-Up; I Set-Up Menu Options; Using The Set-Up Screen; Power Save Setting - FujiFilm FinePix A405 Owner's Manual

SET-UP

I SET-UP Menu Options

Settings Display Default setting
IMAGE DISP. ON/OFF ON
POWER SAVE ON/OFF ON
FORMAT OK –
LOW/HIGH/OFF LOW
BEEP
DATE/TIME SET –
LCD ON/OFF ON
FRAME NO. CONT./RENEW CONT.
USB MODE
/ PC
ENGLISH
VIDEO SYSTEM NTSC/PAL PAL
DISCHARGE OK –
RESET OK –

USING THE SET-UP SCREEN

0 1 0 3 0 2
0 4 0 5
46
Explanation
This option specifies whether or not an image checking screen
(photography results) is displayed after you take a shot.
The photographed image is displayed for a few moments and
then automatically recorded.
This option allows you to specify whether the LCD monitor
switches off to conserve power if the camera is not used for 30
seconds. See P.47 for details.
Erases all files. See P.48 for details.
Sets the volume of the tone emitted when the camera controls
are used.
Use this option to correct the date or time. See P.14 for details.
Use this option to specify whether the LCD monitor is
automatically switched ON or OFF when the Mode switch is set
to " ".
Specifies whether frame numbers are assigned consecutively
from previous numbers or begin again. See P.48 for details.
Selects the function when the camera is connected to a PC.
See P.59 for details.
Use this setting to specify the language used for LCD monitor
display.
Specifies whether video output is set to NTSC or PAL.
Discharges rechargeable batteries. See P.70 for details.
Resets all the camera settings other than the date and time,
language and video output settings to the factory default values
set at shipment. Pressing "c" displays a confirmation screen. To
reset the settings, press the "MENU/OK" button.
1 Press the "MENU/OK" button to display the
menu.
2 Press "d" or "c" to select "
" OPTION and
then press "a" or "b" to select "SET-UP".
3 Press the "MENU/OK" button to display the
SET-UP screen.
4 Press "a" or "b" to select a menu option and
then press "d" or "c" to change the setting.
Press "c " for "FORMAT", "DATE/TIME",
" RESET" or "DISCHARGE".
5 After modifying the settings, press the
"MENU/OK" button to confirm the changes.
G
!
Always switch the camera off when replacing the batteries.
Opening the battery cover or disconnecting the AC power
adapter without switching the camera off, the camera settings
may revert to the default setting set at shipment.

POWER SAVE SETTING

N
When the camera has switched off
Power consumption is kept to a minimum to
prevent battery depletion. Select the "ON" setting
when you are using alkaline batteries.
G
!
The Power Save setting is disabled during automatic
playback, during rechargeable battery discharging and when
a USB connection is being used.
h Power saving "ON"
1 If the camera is not used for approximately 30
seconds, the LCD monitor switches off
temporarily to reduce power consumption (The
viewfinder lamp (green) blinks at 1-second
intervals).
Pressing the Shutter button down halfway at this
point restores the camera to the ready-to-shoot
status.
2 If the camera is left unused for 90 seconds after
the LCD monitor switches off, the camera is
automatically switched off (the viewfinder lamp
switches off).
G
!
The charging time for the flash increases slightly because the
flash charging power is reduced.
G
!
Pressing the Shutter button down halfway and then releasing
it, the screen may go dark briefly because the flash is
charging.
If the camera is left unused for about 2 minutes in
Playback mode, during setup or while the LCD
monitor is switched off, the camera is automatically
switched off. However, the LCD monitor does not
switch off if the camera is left unused for 30
seconds in Playback mode or during setup.
h Power saving "OFF"
Because the camera is not switched to low power
consumption mode, the batteries will run down
more quickly. However, this function automatically
switches the camera off if the camera is not used
for approximately 2 minutes.
N
To restore power to the camera, slide the "POWER"
switch to the ON position again.
47