Advertisement
Table of Contents
- 1 Included Items
- 2 Location and Mounting
- 3 Installation Location
- 4 Mounting the Amplifier
- 5 Connecting the Power and Ground
- 6 Using the Connectors
- 7 Ground Connection
- 8 Power Connection
- 9 Subwoofer Connection
- 10 Input Connections
- 11 Setup Procedure
- 12 Bass Boost
- 13 Troubleshooting
- 14 Specifications
- Download this manual
Advertisement
Table of Contents
Related Manuals for JBL GTO-1001EZ
Summary of Contents for JBL GTO-1001EZ
- Page 1 GTO-1001eZ/ GTO-751eZ/GTO-501eZ subwoofer amplifier Owner’s Manual...
-
Page 2: Included Items
JBL GTO subwoofer amplifiers include Simple Setup designed to make it easy for you to get all the noise- free power your amp is capable of delivering. -
Page 3: Mounting The Amplifier
If your audio system’s source unit includes a remote turn-on wire and you would prefer to use it, the amplifier will sense that you’ve used a remote turn-on wire and that connection will override the signal-sensing turn-on. If necessary, you can defeat the signal-sensing turn-on circuit by moving the Auto Turn-On switch to the “Off” position. www.jbl.com... -
Page 4: Connecting The Power And Ground
Connect a wire (minimum 6AWG – 13.2mm – for the GTO-1001EZ; minimum 8AWG – 8.4mm – for the GTO-751EZ and GTO 501EZ) from the amplifier’s GND terminal directly to a solid point on the vehicle’s chassis. For a good connection, use sandpaper to clear the paint from the metal surface at this chassis location. -
Page 5: Power Connection
GTO-751EZ and GTO-501EZ) directly to the battery’s positive (+) terminal. 2. Install a fuse holder for a 120A fuse (GTO-1001EZ), 80A fuse (GTO-751EZ) or 50A Fuse (GTO-501EZ) on this wire within 18" (46cm) of the battery’s (+) terminal. Do not install the fuse in the holder at this time. -
Page 6: Input Connections
input cOnnectiOns Input Connectors Use RCA audio cables to connect source units with preamp-level outputs to the amplifier; use the supplied bare wire- to-RCA adapters to connect to source units that don’t have RCA output connectors. Use a small Phillips screwdriver to loosen the adapter’s set screws and insert the speaker wires into the holes on the back of the adapter. - Page 7 8. When the amplifier’s Gain Indicator LED is lit green, the GTO amplifier gain setup is complete. nOte: Set the amplifier’s Gain LED switch to the “Off” position to prevent the red LEDs from lighting up continually during normal operation. www.jbl.com...
-
Page 8: Bass Boost
Bass BOOst The Bass Boost control provides up to 12dB of bass boost at 45Hz. Set this control according to your personal taste, but be careful not to set the control at a high enough level to cause audible distortion or bottoming of your subwoofer. pOWer/prOtectiOn led Power/ Protection... -
Page 9: Troubleshooting
TrOubleshOOTinG If your amplifier isn’t performing the way you think it should, check to see if the problem is covered in this section before calling your dealer or contacting JBL customer service. prOBlem causes and sOluTiOns No sound (the amplifier’s •... -
Page 10: Specifications
Number of Channels: Power Output (CEA 2006A): 650W RMS x 1 channel at 4 ohms, 14.4V DC, <1.0% THD 1000W RMS x 1 channel at 2 ohms, 14.4V DC, <1.0% THD Max Power: 1450W x 1 channel at 2 ohms (50Hz), 15.5V DC, 10% THD Frequency Response: 10Hz –... - Page 11 8500 Balboa Boulevard, Northridge, CA 91329 USA © 2011 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, specifications and appearance are subject to change without notice.