NEC VT45 Quick Connect Manual page 2

Basic Menu
Source Select
RGB
Video
S-Video
Picture
Brghtness
Contrast
Color
Basic Menu
Hue
Sharpness
Source Select
Picture
Volume
Volume
Image Options
Image Options
Keystone
Projector Options
Lamp Mode Normal/Eco1/Eco 2
Information
Factory Default
All Data/Current Signal
Projector Options Menu
Menu Menu Mode
Language
Setup
Source Display
No Input Display
Volume Bar
Keystone Bar *
Filter Clean Message
Menu Display Time
* This setting is optional. you need the optional presentation
remote control (PR51KIT).
setup
Orientation
Cinema Position
Background
Page 1 (Source Index/Input Terminal/Horizontal Frequency/Vertical Frequency/Sync
Polarity)
Page 2 (Signal Type/Video Type/Sync Type/Interlace)
Page 3 (Remaining Lamp Time/Lamp Hour Meter/Projector Usage)
Troubleshooting
Power/ Status Light Messages
Condition
Standby
Cooling down
Lamp in Nomal mode
Lamp in Eco 1 mode
Lamp in Eco 2 mode
One minute after lamp is turned on
Retrying to turn on lamp
Lamp has reached its end of life
(1000 hours or over : Normal mode)
(1500 hours or over : Eco 1 mode)
(2000 hours or over : Eco 2 mode)
Basic/Advanced
Lamp life has reached its end of life
English/German/French/ (1100 hours or over : Normal mode)
Italian/Spanish/Swedish/ (1600 hours or over : Eco 1 mode)
Japanese (2100 hours or over : Eco 2 mode)
On/Off
Lamp or filter cover error
(3 locations)
On/Off
Temperature error
On/Off
On/Off
Fan error
On/Off
Manual/Auto 5 sec/Auto 15
sec/Auto 45 sec
Lamp error
Desktop Front/Ceiling Rear/
Desktop Rear/Ceiling Front
Top/Center/Bottom
Blue/Black/Logo
Power Indicator Note
Status Indicator
Steady orange – –
Blinking green
– Blinks green for 60 seconds.
Steady green –
–
Steady green
Steady orange –
Steady green –
Steady green
Blinking green Depending Lamp mode Do not turn off the projector during
this condition.
Steady green The projector retries 3 times at an
Blinking orange
interval of 15 sec for max. 45 sec).
Steady green
Steady red Message appears on screen during
this condition. The projector reaches
its end of life. Please replace the
lamp as soon as possible.
Steady orange The projector is in standby mode and
Steady red
cannot be turned on.
Steady orange The projector is in standby mode and
Blinking red
cannot be turned on.
(1 sec interval)
Steady orange Blinking red The projector is in standby mode and
(4 sec interval) cannot be turned on.
Steady orange The projector is in standby mode and
Blinking red
(8 sec interval) cannot be turned on.
Steady orange
Blinking red The projector is in standby mode and
cannot be turned on.
(12 sec interval)
Common Problems & Solutions
Problem Check These Items
Does not turn on • Check that the power cable is plugged in and that the power button on the
projector cabinet or the remote control is on.
• Ensure that the lamp cover is installed correctly. See page E-36.
• Check to see if the projector has overheated or the lamp usage exceeds 1100
hours (2100 hours in Eco 2 mode and 1600 hours in Eco 1 mode). If there is
insufficient ventilation around the projector or if the room where you're presenting
is particularly warm, move the projector to a cooler location.
No picture • Use the menu to select your source (Video, S-Video or RGB). See page E-29.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page E-29.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Factory
Default on the Image Options Menu. See page E-31.
Image isn't square to the screen • Reposition the projector to improve its angle to the screen. See page E-14.
• Use the Keystone on the Image Options Menu to correct the trapezoid distortion.
See page E-29.
• Adjust the focus. See page E-23.
Picture is blurred
• Reposition the projector to improve its angle to the screen. See page E-14.
• Ensure that the distance between the projector and screen is within the
adjustment range of the lens. See page E-15.
• Use menus or Source button on the remote control or the cabinet to select the
Image is scrolling vertically,
source you want to input.
horizontally or both
• Install new batteries. See page E-13.
Remote control does not work
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. See page E-13.
Status indicator is lit or blinking • See the Power/ Status Light messages.
• If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image
Cross color in RGB mode
with the Position and Clock Adjust on the Advanced Options Menu. See page
E-31.