CDMA Portable Cellular Telephone SCH-470 SERVICE Manual CONTENTS CDMA Portable Cellular Telephone 1. General Introduction 2. Specification 3. NAM Programming 4. Data Tr a n s f e r 5. Circuit Description 6. Exploded View and Its Parts List 7. PCB Diagrams 8.
Page 2
£ Samsung Electronics Co.,Ltd. APR. 1998. Printed in Korea Code No. : GH68-60687A...
1 . General Int roduct ion The SCH-470 cellular phone functions as only digital cellular phone working in CDMA (Code Division Multiple Access) mode. CDMA type digital mode applies DSSS (Direct Sequential Spread spectrum) mode which first came to be used in the military.
Page 4
° ‹ MSC Receiver Frequency FA NO. CH. NO. CENTER FREQUENCY FA NO. CH. NO. CENTER FREQUENCY 1011 869.640MHz 882.120MHz 870.870MHz 883.350MHz 872.100MHz 884.580MHz 873.330MHz 885.810MHz 874.560MHz 887.040MHz 875.790MHz 888.270MHz 877.020MHz 889.270MHz 878.250MHz 890.910MHz 879.480MHz 892.140MHz 880.890MHz 893.370MHz Samsung Electronics...
5. Setup NAM 4 ; Display the variable of CDMA used commonly when you select NAM 4. If you don't store the data by pressing STO key after modifying as explains, the data does not change. You can check the data by pressing VOLUME key without changing the data. Samsung Electronics...
Page 8
Preferred system selection for NAM2. Digital only Up to four NAMs are allowed for the phone. This lists one of the four NAMs. Pref NAM3... Preferred system selection for NAM3. Digital only Pref NAM4... Preferred system selection for NAM4. Digital only Samsung Electronics...
Page 9
Default setting is 10640,8103,0,0,0,0 : ranges from 0 to 32,767 up to six SIDs. ¶S or ¶H CDMA Home System ID. CDMA HomeSID Enables the phone to allow mobile terminated calls while in Y e s the home system. Controls the types of registration allowed for the phone. Samsung Electronics...
Page 10
See SID #1. SID #2 number See NID #1. NID #2 number See SID #1. SID #3 number See NID #1. NID #3 number See SID #1. SID #4 number See NID #1. NID #4 Samsung Electronics...
Page 11
The NAM3 setup program is the same as °ÆNAM1°Ø . See NAM1. 3-5 Setting Up NAM4 LCD Display Key in Function -choose 'NAM4’. NAM Program 5:Setup NAM4 The NAM4 setup program is the same as °ÆNAM1°Ø . See NAM1. Samsung Electronics...
4 . Dat a Transfer When the main board of a customer's cellular Displays SAMSUNG logo. To reenter phone is required to be replaced with a new one, to program mode, press F3 key again. or the customer is needed to use a phone lent from the service center while his phone is serviced, this Write the data of the customer’s phone...
Page 14
You can restart to read the data. Writing is interrupted in the middle of the operation ¶ You can clear the error message by pressing any key. due to some problem with the phone. Writing is cancelled. You can restart writing from the beginning. Samsung Electronics...
The CPU controls all from the MSM. It also consists a DC-DC converter the circuitry. For the CPU clock, 27MHz resonator to supply -3.5V for fine view angle and LCD is used. reflector to improve the display efficiency. Samsung Electronics...
Page 16
¶UFMCLK: TXclock used in FM mode. Power Down Control When the IDLE/ signal turns LOW, only the TX sections will be disabled. If both the IDLE/ and SLEEP/ change to LOW, all the pins except for the TCXO and 27MHz clock are disabled. Samsung Electronics...
Page 17
(U111), and comes out to speaker. sent to the speaker unit. TX WBD, ST,SAT These signals are generated from MSM. The modulation level of TX WBD and ST is 8 kHz/dev, and SAT is ° 2 kHz/dev. Samsung Electronics...
IF AGC output level is applied to BBA (Baseband Analog ASIC). The IF AGC amp (U302) keeps the signal at a constant level by controlling the gain. Dynamic range is 90dB, up gain +45dB, and down gain -45dB. Samsung Electronics...
Page 19
VOLTAGE CONTROLLED TEMPERATURE COMPENSATED CRYSTAL OSCILLATOR (VC- TCXO, U343) It provides 19.68 MHz reference frequency to PLL. A correct frequency tuning is made by the voltage control. Samsung Electronics...
°æ12.5 MHz first local signal. RF AUTOMATIC GAIN CONTROLLER AMP (U461, U464) The signal out to the base station should be a constant level. The TX RF AGC amp controls power to keep the signal at a constant level. Samsung Electronics...
Page 21
(R23//R24) °§ Vr IC = (R25//R77) [ R26//(•· R27)// (•‚ R28)//(•„ R29)] Vr = R47 + R48 R68 and C49 are used to compensate the phase difference occured due to the time delay for the circuit. Samsung Electronics...
Page 22
U2 off. R45 and C36 are used to MPU through the analog switch U25. measured at compensate the phase difference caused by the the pin 14 of the MPU through U25. time delay. Vd = (R50 + VR21) + R55 Samsung Electronics...
Page 23
It has a linear characteristic reset within a specified time by MPU, MPU will be by R51 and R52, and is measured at the pin 14 of automatically reset by the timer. the MPU through U25. Samsung Electronics...
Page 25
6. Expl oded Vi ew and i t s Par t s Li st 6-1 Fixed Phone Exploded View 6-2 Fixed Phone Parts List 6-3 Rapid Charger Exploded View 6-4 Cradle Dummy Ass’y & Cigar Lighter Adapter Samsung Electronics...
T_SIO_MODE_I SIO mode change. 67(C6, 3, 6) T_READ_BATT_I Reads Low-Bayyery in the standby, talk. 68(C8, 0, 3) T_VBATT1_I Set the low battery position in the standby. 69(C9, 0, 3) T_VBATT2_I Set the low battery position in the talking. Samsung Electronics...
Page 58
After you get a desired test value by performing these commands, if you want to save the value into EEPROM, use T-SAVE-VAL-I command to store the test value into the corresponding position. OP: Operation Command Number ¶S AB: Input Argument Byte Number RB: Return Byte Number Samsung Electronics...