Listening Through A Receiver; Troubleshooting For Anynet - Samsung 4 series User Manual

Listening through a Receiver

¦
You can listen to sound through a receiver (i.e Home Theater) instead of the TV speaker.
1. Select Receiver and set to On.
2. Press the EXIT button to exit.
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the
OUT (OPTICAL) jack of the TV.
✎
When the receiver (i.e Home Theater) is set to On, you can hear sound output from the TV's Optical jack. When
the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
NOTE
x
You can only control Anynet
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet
x
The Anynet functions do not operate with other manufacturers' products.
+

Troubleshooting for Anynet

¦
Problem
Anynet + does not work.
I want to start Anynet .
+
I want to exit Anynet .
+
The message 'Connecting to
Anynet device...' appears on
+
the screen.
The Anynet device does not
+
play.
The connected device is not
displayed.
The TV Program cannot be
recorded.
The TV sound is not output
through the receiver.
devices using the TV remote control, not the buttons on the TV.
+
+
Possible Solution
• Check if the device is an Anynet
• Only one receiver (home theater) can be connected.
• Check if the Anynet + device power cord is properly connected.
• Check the Anynet + device's Video/Audio/HDMI cable connections.
• Check whether Anynet (HDMI-CEC) is set to On in the Anynet
+
• Check whether the TV remote control is in TV mode.
• Check whether the remote control is Anynet
• Anynet + does not work in certain situations. (Searching channels, operating Media Play or Plug & Play
(initial setup), etc.)
• When connecting or removing the HDMI cable, please make sure to search devices again or turn your
TV off and on again.
• Check if the Anynet + Function of Anynet
• Check if the Anynet device is properly connected to the TV and check if the Anynet
+
set to On in the Anynet Setup menu.
+
• Press the TOOLS button to display the Anynet
• Select View TV in the Anynet
• Press the SOURCE button on the TV remote control and select a device other than Anynet
• Press > CH CH LIST, PRE-CH, and
<,
button operates only when a tuner-embedded Anynet
• You cannot use the remote control when you are configuring Anynet
• Use the remote control when the Anynet
• You cannot use the play function when
• Check whether or not the device supports Anynet
• Check whether or not the HDMI cable is properly connected.
• Check whether Anynet (HDMI-CEC) is set to On in the Anynet
+
• Search Anynet devices again.
+
• You can connect an Anynet
+
Anynet functions.
+
• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a
power failure, please repeat the device scan.
• Check whether the antenna jack on the recording device is properly connected.
• Connect the optical cable between TV and the receiver.
+ device. The Anynet + system supports Anynet
+ compatible.
+ device is set on.
menu and select a menu you want.
+
menu.
+
FAV.CH to change the TV mode. (Note that the channel
device is not connected.)
+
setting or switching to view mode is complete.
+
Plug & Play (initial setup) is in progress.
functions.
+
device using the HDMI cable only. Some HDMI cables may not support
DIGITAL AUDIO
device.
+
+ devices only.
+ setup menu.
(HDMI-CEC) is
+
devices.
+
or switching to a view mode.
+
setup menu.
+
English
29