Advertisement
phillips screwdriver
23.
Move washer/dryer to its
permanent location.
To exhaust the dryer straight from
back of the washer/dryer
unit,
determine
if any additional
exhausl
duct is needed
(see exhaust
requirements,
Panel B ). To exhaust
the dryer to either side or inside
check if additional
exhaust duct is
needed
and see Alternate
Exhaust
Methods, Panel F Connect exhaust
duct to exhaust hood.
placing
a carpenter's
level on top of
washer, first side to side then front to
back. If it is not level, screw the front
legs up or down to adjust. Tilt
washer/dryer
forward raising back
legs 1" off of floor to adjust rear self-
leveling legs. Gently lower washer to
floor. Make final check with level.
Check that you have all of your tools,
'
29.
Turn on water faucets and check for
leaks. Tighten couplings
if there is
leaking.
Use duct tape to seal all joints.
30.
25.
Plug electrical
cord into grounded
outlet.
CHECK ELECTRICAL REQUIREMENTS.
BE SURE YOU HAVE CORRECT
ELECTRICAL SUPPLY AND
RECOMMENDED GROUNDING
METHOD.
Check the installation
instructions to see that you have
completed
each step. Complete
any missed steps before you
31.
If access panel was removed to
install ductwork,
replace
access
panel. Be sure to tighten both screws.
32.
Take a few minutes and read the Use
and Care Guide to fully understand
your new washer/dryer.
Now start
the washer and allow it to complete
the regular cycle.
Put "hook" end of drain hose in tub or
standpipe.
Tightly wrap the plastic strap
around
the drain hose and tub or
standpipe
or inlet hose as shown in
Figures A-C.
If drain hose cannot be
strapped in place, it must be
cut exactly to length so the
"hook" end is held tightly
over the edge of the tub or
standpipe.
26.
Check that all parts are now
installed.
See parts list, Panel B. If
there is an extra part, go back
through steps to see which step
If a longer drain
hose is needed,
drain hose (Pat
was skipped.
No. 388423) and
hose extension
kit (Part No.
285442)
are
available
from a
Whirlpool-authorized
parts distributors.
If
drain hose must be shortened,
use hose
kit (Par-t No. 285442).
Note: If washer/dryer
is moved to adjust
drain hose, the washer/dryer
must be
leveled again. Repeat Step 20. Place
cardboard
under the washer/dryer
and
carefully move washer/dryer
to avoid
damaging
floor covering.
Remove tape from dryer door and
open door. Remove the tape across
the dryer lint screen. Check to be
sure lint screen is in its proper
position. Wipe out drum. Start dryer
and allow it to complete
a cycle to
make sure the dryer is working
properly
I
34.
Finally, save all literature and keep
with the washer/dryer,
Save all
shipping
materials for reshipping.
Remove the two foam
shipping
pieces
between
washer and
dryerand
place with
othershipping
pieces. If the
exhaust ductwork
cannot
be connected
from the side of the
washer/dryer,
the exhaust duct can
be reached
from the front, through
the access panel. Remove the
access panel by unscrewing
2
phillips head screws located
at the
top of the panel. Set panel and
screws aside.
new Whirlpool washer/dryer.
To get the most efficient use from
your new washer/dryer, read your
Whirlpool Use and Care Guide.
27,
1 Congratulations! )
Check that you removed all the
shipping
pieces including
the three
shipping straps with keys.
If you do not remove the shipping
straps, your washer/dryer
may
'Walk" away from its location.
Keep installation
instructions
~~~~~~
PANEL E
Advertisement
