Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for Blaupunkt Montreal RCM 45
Summary of Contents for Blaupunkt Montreal RCM 45
- Page 1 Radio / Cassette Montreal RCM 45 Operating instructions...
-
Page 3: Table Of Contents
Contents Short instructions ......19 Radio operation with RDS ... 25 Tape operation ......29 AF - Alternative frequency ....25 Inserting a tape ........29 Important notes ......22 REG - regional programme ....25 Removing a tape ........29 Precautions ........... -
Page 4: Short Instructions
Short instructions 1 On 2 LD GEO – Volume Loudness - When listening at a low To adjust the balance (left/right) and level, the Loudness function creates a fader (front/rear) with the rocker switch. more natural sound by boosting the low frequency range. - Page 5 4 DSC (Direct Software Control) ; Display If lo does not light up, the radio will also Use the DSC function to customise pick up weaker, distant stations (high Radio operation: certain programmable, basic settings to sensitivity). suit your personal needs and prefe- To switch over: Press lo briefly.
- Page 6 < PROG button / Fast winding ? 1, 2, 3, 4, 5, 6 - preset buttons B FM - FM, Travelstore You can store six stations on each FM To switch between the FM memory To switch to the other side of the memory bank (I, II, T).
-
Page 7: Important Notes
As the driver of a motor vehicle, it is your Use only the accessory and replacement responsibility to pay attention to the traffic Down parts approved by Blaupunkt. Up/down in short intervals situation at all times. Never use your car radio (“AF” must be switched off) in a way that could distract you. -
Page 8: Anti-Theft Protection
Anti-theft protection Release panel Fitting the release panel further attempts, the waiting time extends to one hour. • Insert the panel on the left side first with This unit is equipped with a release panel After 20 unsuccessful attempts, the display the cassette slot facing up and then (detachable face). -
Page 9: Re-Start Following An Interrup-Tion Of The Power Supply
• Enter the code number given in the • Press preset buttons 1 and 4 simulta- Blaupunkt car radio passport: neously and hold down while switching Example: The code number is 2521. the set on again. - Press preset button 1 twice; the dis- The display shows “CODE”. -
Page 10: Radio Operation With Rds
Radio operation with RDS (Radio Data System) The Radio Data System offers you more If “SEARCH” appears in the display when If you leave the service area of the regional convenience when listening to FM radio sta- switching on the radio or recalling one of the programme tuned into, or if you would like to tions. -
Page 11: Manual Tuning
Scrolling through the broad- Automatic tuning • Press the FM button as many times casting network (only FM) until the desired memory bank lights up in the display. You can use the << >> buttons to tune in stations of your reception area. Storing stations If several programmes of one broadcasting network can be received, you can scroll... -
Page 12: Automatically Storing The Strongest Stations With Travelstore
Automatically storing the stron- Scanning stored stations The scanned frequency or the station gest stations with Travelstore with Preset Scan name will start flashing in the display. During the actual scanning process You can automatically store the six most You can have all of the stored stations played “SCAN”... -
Page 13: Switching From Stereo To Mono (Fm)
Receiving traffic programme stations with RDS-EON Switching from stereo to mono Many FM broadcasters offer traffic messa- When pressing TA while a message is being (FM) ges for their service area at regular intervals. broadcast, this message will be interrupted. All traffic programme stations transmit a spe- The unit will then switch back to the previous If reception is poor, you may get better sound... -
Page 14: Automatic Seek Tuning Start
Tape operation Inserting a tape Automatic seek tuning start “TR1--...” for track (side) 1 or A or “TR2--...” (tape operation) for track 2 or B. • Turn on the set. When leaving the reception area of the tuned • Insert a tape. Notice: in traffic programme station while listening to If there is too much tension on the tape during... -
Page 15: Tape Equalisation With Mtl
DSC programming Tape equalisation with MTL DSC (Direct Software Control) allows you to (lo off) customise certain programmable, basic set- To adjust the seek tuning Switch on the MTL function to select the best tings to suit your personal needs and prefe- sensitivity for distant recep- equalisation response when using metal or rences and then store them. -
Page 16: Overview Of The Dsc Factory Settings
Overview of the DSC factory BEEP Confirmation tone for all LOUD Loudness - When listening settings functions which require a at a low level, the Loud- button to be pressed for ness function creates a LOCAL more than 2 seconds. more natural sound by The volume can be adju- boosting the low frequency... -
Page 17: Cd Changer Control (Optional)
CD changer control (optional) Selecting a track using the You can operate the Blaupunkt CD changer To stop the SCAN: rocker switch / selecting a disc CDC-A05 in combination with this car radio. • Press the SC button briefly once again. -
Page 18: Appendix
Appendix Specifications Care notes Amplifier Release panel Output power: 4 x 6 W RMS power To ensure that the unit functions properly it is important that the contacts between the re- acc. to DIN 45324/3.1 lease panel and the head unit are free from 4 x 8 W max. - Page 19 Blaupunkt-Werke GmbH Bosch Gruppe 7/95 K7/VKD 8 622 400 019...