Table of Contents
Related Manuals for Patton electronics 1001RP Series
Summary of Contents for Patton electronics 1001RP Series
- Page 1 Model 1001RP Series Rack Power Supply System Part# 07M1001RPSVC-C SALES OFFICE Doc# 078452UC (301) 975-1000 Revised 09/14/99 TECHNICAL SUPPORT C E R T I F I E D (301) 975-1007 An ISO-9001 http://www.patton.com Certified Company...
-
Page 2: Table Of Contents
5.4 Installing the Rear Power Entry Cards 5.5 Installing the Front Power Cards (Initial Installation) The Model 1001RP Series units generate and use radio frequency 5.6 Making the Alarm Relay Connections energy, and if not installed and used properly—that is, in strict accor- 5.7 Connecting a 1001RPEM-RAC Entry Card to the AC... -
Page 3: General Information
• Redundant supply serves up to 14 function cards Model 1001RP Series. Technical Service hours: 8AM to 5PM EST, • Single supply serves up to 16 function cards Monday through Friday. -
Page 4: Scope
1001RPEM-RAC and 1001RPEM-RVDC power entry Hazardous voltages exist in the primary circuits of AC-input cards. The modules are part of the 1001RP series rack system. power supplies. Beware of internal lethal voltages due to charged capacitors even after the AC input is disconnected. A minimum of... -
Page 5: The 1001Rp16P Rack Chassis
5.0 INSTALLATION 48 volt DC input (42-60 volts) power supply: The complete supply The following sections describe in detail how to properly install the consists of a 1001RPSM-R48V front power supply card and power supply modules, configure the rear power entry card alarm oper- 1001RPEM-RVDC rear power entry card. -
Page 6: Installation .............................................................................7
5.4 INSTALLING THE REAR POWER ENTRY CARDS Steps 3-5 are for redundant applications only: The power supply modules occupy the right-most slots on the rack Attach the ground wire of the second power entry card to the bare system (as viewed from the front). Refer to Figure 2 and follow the metal side of the rear spacer. -
Page 7: Making The Alarm Relay Connections
5.6 MAKING THE ALARM RELAY CONNECTIONS Spare terminal plugs may be obtained directly from Patton Electronics. See Appendix for part numbers, contact ratings and gen- The 1001RPEM-RAC and 1001RPEM-RVDC rear power entry eral alarm port specifications. cards (figure 3, below) feature a 3-position, screw-type terminal plug for the alarm connections. -
Page 8: Service Procedure - Replacing A 1001Rpsm-Rui Front Card
After the DC power supply leads are properly connected and After the connectors meet, gently apply even pressure to the top power is applied, the green "12V" LED on the 1001RPSM-R48V front and bottom of the panel to seat the card. Do not force the card panel will be illuminated and the fan will operate. -
Page 9: Operation
6.0 OPERATION APPENDIX A PATTON ELECTRONICS MODELS 1001RPSM-R48V plus Once the Model 1001RP Series power supply module is properly 1001RPEM-RVDC, 48VDC SPECIFICATIONS installed, you are ready to operate the unit. Figure 4 (below) shows the location of LED indicators. Input Specifications... - Page 10 APPENDIX A APPENDIX A (continued) (continued) PATTON ELECTRONICS MODELS 1001RPSM-R48V plus PATTON ELECTRONICS MODELS 1001RPSM-R48V plus 1001RPEM-RVDC, 48VDC SPECIFICATIONS 1001RPEM-RVDC, 48VDC SPECIFICATIONS Interface Signals and Internal Protection Safety, Regulatory and EMI Specifications PARAMETER CONDITIONS/DESCRIPTION UNITS PARAMETER CONDITIONS/DESCRIPTION UNITS Indicators GREEN indicator for normal Operating At 100% load.
- Page 11 APPENDIX B APPENDIX B (continued) PATTON ELECTRONICS MODEL 1001RPSM-RUI plus 1001RPEM-RAC, UNIVERSAL AC INPUT SPECIFICATIONS PATTON ELECTRONICS MODEL 1001RPSM-RUI plus 1001RPEM-RAC, UNIVERSAL AC INPUT SPECIFICATIONS Input Specifications Interface Signals and Internal Protection PARAMETER CONDITIONS/DESCRIPTION UNITS PARAMETER CONDITIONS/DESCRIPTION UNITS Input Voltage - AC Universal input, Auto ranging.
-
Page 12: Appendix C - Replacement Parts And Accessories
APPENDIX B APPENDIX C (continued) PATTON MODEL 1001RP FACTORY REPLACEMENT PARTS AND ACCESSORIES PATTON ELECTRONICS MODEL 1001RPSM-RUI plus 1001RPEM-RAC, UNIVERSAL AC INPUT SPECIFICATIONS Patton Model # Description Safety, Regulatory and EMI Specifications PARAMETER CONDITIONS/DESCRIPTION UNITS 1001RPSM-R48V....Redundant 48-VDC Front Power Supply Operating At 100% load. - Page 13 APPENDIX D Safety Agency Recognition Plenum Installation Compliance with NRTL/UL 1950/EN60950 Safety agency regulations require the use of an approved plenum (Patton part number (05R16PL) with each 1001R rack installation. A rack chassis fitted with the plenum constitutes an agency recog- nized fire enclosure.