Wharfedale Pro SVP-12PM User Manual

SVP Power Fold 24 June 22/6/04 4:33 pm Page 1
S V P - P S E R I E S P O W E R E D
MODEL SVP-12PM SVP-15P
FREQUENCY RESP +/- 3 DB 50 - 20kHz 45-20kHz
SYSTEM IMPEDANCE 8 4
POWER AMP MODULE 300W RMS 300W RMS
450W PEAK 450W PEAK
INPUT NUMBER AND TYPE 1 X 1/4"Phone 1x combined
jack and XLR jack and XLR
OUTPUT NUMBER AND TYPE 1 X 1/4"Phone 1 x male XLR
EXTENSION SPEAKER OUT 1 X 1/4"Phone No
LEVEL CONTROL Yes Yes
EQ CONTROL 5 band EQ No
CROSSOVER FREQUENCY SWITCH No No
PHASE REVERSE SWITCH No No
STAND ADAPTOR No Yes
PRODUCT DIMS (mm) H x W x D 415 x 428 x 554 638 x 463 x 390
WEIGHT 17.5kg 21.76kg
SVP-12PM Panel & Description:
1. Level control: The Level control adjusts the overall volume
of the amplified signal.
2. 5 band EQ: Use this Five-Band Graphic EQ to cut or boost
your signal up to 12dB at designed frequency centers.
This is useful for reducing low frequency rumble or
feed back that often occurs on stage.
2
3. Parallel Line input and output: These two jacks are
provided to supply a signal input to the SVP -12PM and to
allow for daisy chaining the signal to possibly another
SVP-12PM or amplifier combination.
4. Speaker out: The Speaker Out is post EQ, powered
output. Designed for a minimum impedance of 8 ohms
speaker. This output should be connected only to non-
powered monitor speakers. The SVP-12M is the perfect
extension monitor to use in this application.
5. Power switch: use this switch to turn the unit on and off.
6. AC Input connector: The line cord (included) which
provides AC power to the unit. Connect the line cord to
this connector and to a properly grounded AC supply.
Damage to the equipment may occur if an improper line
voltage is used.
NEVER REMOVE OR CUT THE GROUND PIN OF THE
LINE CORD PLUG
7. Fuse: If the fuse should fail, it must be replaced with the
same type and value in order to avoid damage to the
equipment and prevent voiding the warranty.
L O U D S P E A K E R S
SVP-15PB SVP-18PB
45 - 300kHz 40-300kHz
4 4
300W RMS 300W RMS
450W PEAK 450W PEAK
1x combined 1x combined
jack and XLR jack and XLR
1 x male XLR 1 x male XLR
No No
Yes Yes
No No
150/250Hz 150/250Hz
Yes Yes
Yes Yes
587 x 548 x 429 748 x 548 x 450
32.54kg 39.6kg
1
5
6
7
3 4
Wharfedale International Limited, IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU England
IAG Professional reserve the right to alter or improve specifications without notice.All rights reserved © 2004 Wharfedale Pro. A member of the International Audio Group
WHARFEDALE website : www.wharfedalepro.com
SVP-P SERIES PROFESSIONAL SPEAKER
SYSTEMS USER MANUAL
SVP-12PM, SVP-15P, SVP-15PB & SVP-18PB.
W A R N I N G & S A F E T Y I N S T R U C T I O N S
1. READ INSTRUCTIONS carefully before operating this product. with an extension cable unless the pins can be fully inserted.
2. RETAIN these instructions. 7. CABLES - Use quality screened cables for signal connections.
3. COMPLY WITH WARNINGS - All warnings and instructions for
8. RIGGING • SUSPENDING • MOUNTING
this product should be adhered to. The rigging, suspension or mounting of this speaker system can
expose members of the public to serious health risks and even
4. WATER & MOISTURE - This Wharfedale Pro unit should
death. UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUS-
not be used near liquids. If should not have liquids placed on or
PEND OR OTHERWISE MOUNT THIS SYSTEM UNLESS YOU
in close proximity as there are DANGEROUS VOLTAGES
ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELE-
present.
VANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL
RELEVANT SAFETY REGULATIONS MUST BE FOLLOWED. IF
5. VENTILATION/AIR FLOW: This Wharfedale Pro unit
YOU ARE NOT PROPERLY QUALIFIED OR DO NOT KNOW OF
should not have its heat sinks obstructed from air flow. It should
not be situated in a built-in installation that may hamper air flow to PERTINENT REGULATIONS, CONSULT QUALIFIED PERSON-
NEL FOR ADVICE AND ASSISTANCE.
the heat sinks. It should not be placed near heat sources.
9. CAUTION: These professional loudspeaker systems are
6. POWER SUPPLY: This Wharfedale Pro unit should be
capable of generating very high sound pressure levels. Use care
only connected to a power supply as stated on the unit. Power
with placement and operation to avoid exposure to excessive lev-
supply cables should be routed where they will not be walked on
els that can cause permanent hearing damage.
or pinched by objects placed adjacent or upon them.
10. SERVICING - The user should not attempt to service this
7. ELECTRIC SHOCK: Care should be taken that the ground-
product except that mentioned in this manual.
ing of this unit is NOT defeated. Do not use this units power cable
Wharfedale Pro SVP-P Series of Professional Sound Reinforcement Loudspeakers
● 300W RMS amplifier ● Integral tripod stand adaptor (except monitors)
● 5 Band EQ on SVP-12PM monitor ● Balanced line output
● Durable black carpet finish ● Combined Jack and XLR balanced input connectors
● Integral High Frequency Driver Overload protection ● Power on/off LED on front and back of unit
"PRO-TECH"™ ● Heavy duty steel grille
● Thermal overload, DC fault and short circuit protection
Unpacking Wharfedale Pro Limited Warranty*
Wharfedale Pro SVP-P Series loudspeaker systems are warranted to be
All Wharfedale Pro products are fully
clear of manufacturing or materials defects for a period of one year from
checked before leaving the factory. After
unpacking please inspect cabinets for any the original date of purchase. In the event of malfunction, contact your
physical damage. Please retain the ship- authorised Wharfedale Professional dealer or distributor for information.
ping carton if possible and internal packing
material in case the unit needs to be
returned. Please check as soon as possible the unit is functioning. In
*Be aware that warranty details may differ from country to country. Contact your dealer or
the event of any damage please contact your dealer immediately so
distributor for information. These terms do not infringe your statutory rights.
that a written claim for damages can be made.
Operating/Use 4. If using XLR CONNECTORS, insert the XLR until locked in. If
1. The SVP-P series has 1 x 1/4" phone jack sockets on the SVP- using a jack plug insert until secure.
12PM. The SVP-15P, SVP-15PB and SVP-18PB all feature 1 x 5. Power up audio mixer or processor ensuring connections are
combined jack and XLR inputs.2. Connect the provided power made.
cable to the IEC mains connector on rear of cabinet. 6. Power up SVP-P internal amplifier with levels on zero. Confirm
3 Connect the signal cable (balanced or un balanced, see table SVP-P speakers are operating.
and description) from audio mixer or processor securely to your 7. The SVP-15P, SVP-15PB and SVP-18PB have 2 XLR/1/4"
SVP-P unit (the internal amplifier should be off, power down Jack Sockets - one line in, for system input and one line out for
mode). Where possible use quality connectors. Only use linking to another SVP-Powered speaker. Two main loudspeakers
screened audio cable for the signal input from the audio mixer or may also be linked to one subwoofer.
processor. If possible use balanced line signal leads for optimum
quality (see description and table of balanced line operation).