Looking For Blockages - Dyson DC25 Operating Manual

ASSEMBLY
• Lie vacuum cleaner flat and push on cleaner head until it clicks. Stand vacuum
up straight, insert wand into hose and push into place until it clicks. Attach tool
to the side of the vacuum cleaner.
USING YOUR DYSON VACUUM CLEANER
Press foot pedal and recline handle to use. The stabiliser stand will automatically
lift up. To switch 'ON', press power button in front of handle. When finished
cleaning, push vacuum cleaner into an upright position and stabiliser wheels will
automatically drop. Use the carrying handle to carry the vacuum cleaner.
CAUTION:
• When returning to the upright position, ensure that the stabiliser wheels are fully
engaged before releasing the cleaner.
• Do not press the cyclone release button while carrying the vacuum cleaner or it
could fall and cause injury.
PLEASE NOTE:
• Fine dust such as plaster or flour should only be vacuumed in very small
amounts.
• Do not use the vacuum cleaner to pick up sharp hard objects, such as small toys,
pins, paper clips etc.
• Consult your flooring manufacturer's recommended instructions before
vacuuming and caring for your flooring, rugs and carpets. Some carpets will
fuzz if a rotating brush bar is used when vacuuming. If this is the case, we
recommend vacuuming in hard floors mode and consulting with your flooring
manufacturer. (Refer to carpets/hard floors section.)
• If used in a garage when cleaning the car, care should be taken to wipe the
soleplate and wheels with a dry cloth after vacuuming to clean off any sand, dirt
or pebbles which could damage delicate floors.
• When vacuuming, certain carpets may generate small static charges in the clear
bin. These are entirely harmless and not associated with the main supply. To
minimise any effect from this, do not put your hand or insert any object into
the clear bin unless you have emptied it and rinsed it out with cold water.
• Only use parts recommended by Dyson; failure to do so could invalidate
your guarantee.
• Do not use any lubricants, cleaning agents, polishes or air fresheners on any
part of the Dyson vacuum.
• This Dyson vacuum is fitted with a thermal cut-out. If any part of the Dyson
vacuum becomes blocked the machine may overheat and automatically shut
off. If this happens, switch off and unplug the Dyson vacuum and allow to cool
before attempting to check filters or for blockages. Clear any blockages before
restarting.
• Store the vacuum cleaner indoors. Do not use or store this vacuum cleaner
below 0°C (32°F). Ensure that the vacuum cleaner is at room temperature
before operating.
CARPETS/HARD FLOORS
The brush bar will always default to 'ON' (spinning) each time you switch on the
vacuum cleaner and recline it for cleaning. The brush bar will automatically stop
if it becomes obstructed. If the brush bar stops during use, please refer to the
'Clearing brush bar obstructions' section.
To switch the brush bar off (e.g. for hard floors), recline the vacuum cleaner and
turn it 'ON', then press the brush bar 'on/off' button – the brush bar will stop
spinning.
HIGH-REACH CLEANING
CAUTION:
• Switch 'OFF' the vacuum before changing tools.
• Powerful suction can cause the hose to 'pull back' – please take care.
• To avoid personal injury and to prevent the vacuum cleaner from falling when
cleaning stairs, do not work with the vacuum above you on the stairs.
• Ensure vacuum is in upright position before using tools.
PLEASE NOTE:
• To release the wand, open the wand cap and pull the red tube until the wand
releases from the vacuum. Tools can be attached to either the hose or wand.
• The brush bar will not rotate when the vacuum is in an upright position.
• Ensure wand cap is closed when not in use.
EMPTYING THE CLEAR BIN
CAUTION:
• Switch 'OFF' and unplug the vacuum cleaner before emptying the clear bin.
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
To remove the clear bin from the vacuum cleaner press the button at rear of
carrying handle. To release the dirt, press the red bin release button.
• To minimize dust/allergen contact when emptying, encase base of bin tightly
in a plastic bag before trigger releases dirt. Remove bin carefully and seal bag
tightly, dispose as normal.
PLEASE NOTE:
• Do not use the vacuum cleaner without the clear bin in place.
CLEANING THE CLEAR BIN
CAUTION:
• Do not immerse the whole cyclone in water or pour water into the cyclones.
• Ensure the clear bin is completely dry before replacing.
PLEASE NOTE:
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the bin in a dishwasher.
8
• When vacuuming, certain carpets may generate small static charges in the clear
bin. These are entirely harmless and are not associated with the mains supply.
To minimise any effect from this, do not put your hand or insert any object into
the clear bin unless you have first emptied it and rinsed it out with cold water.
• Clean the shroud with a cloth or dry brush to remove lint and dust.
WASHING YOUR FILTERS
CAUTION:
• Switch 'OFF' and unplug the vacuum cleaner before removing the filters.
• Ensure filters are completely dry before refitting into the vacuum cleaner.
PLEASE NOTE:
• This vacuum cleaner has two filters, located as shown. It is important to check
your filters and wash with cold water regularly or as required, according to
instructions, to maintain performance.
• The filter in the ball should be rinsed and tapped out until the water runs clean,
then tapped out again to ensure all excess water is removed. Please leave to dry
completely for 24 hours.
• It is normal for the filter in the ball to turn grey in colour. The filters may require
more frequent washing if vacuuming fine dust.
• Do not use detergents to clean the filters.
• Do not put the filters in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
• Register for a filter wash reminder by email (Australia only);
customercare@dyson.com.au

LOOKING FOR BLOCKAGES

CAUTION:
• Switch 'OFF' and unplug the vacuum cleaner before checking for blockages.
• Please ensure vacuum cleaner is upright before removing hose or airway
inspection parts.
• Beware of sharp objects when clearing blockages.
• Refit all parts of the vacuum cleaner securely before using.
PLEASE NOTE:
• Clearing blockages is not covered by your vacuum cleaner's limited guarantee.
If any part of your vacuum cleaner becomes blocked, it may overheat and then
automatically shut off. Unplug the vacuum cleaner and leave to cool down.
Clear blockage before restarting.
CLEARING BRUSH BAR OBSTRUCTIONS
CAUTION:
• Switch off and unplug the vacuum cleaner before clearing brush bar
obstructions. Failure to do so could result in personal injury.
If your brush bar is obstructed, it may shut off. If this happens you will need to
remove the brush bar as shown and clear any obstructing debris.