Advertisement
TWEETER INSTALLATION UR1
UR1 can be installed on the dashboard or recessed in a doorside.
These tweeters are included in the DLS ULTIMATE speaker kits UR5i,
UR6i,UR35i and UR36i.
SURFACE MOUNTING:
Use all accessories coming with the
tweeter. Attach the round bottom plate
(A) with the screws (B) or double
adhesive tape.
The fasten the round holder (C) to the
bottom plate using the screw and nut
(D). The tweeter element (G) is then
attached to the holder with three short
screws (E).
F
E
RECESSED MOUNTING:
You need a hole with a diameter of 45 mm / 1,77" in the door side.
Attach the tweeter element (G) to the door side with the round holder
(C) on the back side of the door panel. Use the three long screws (F)
to attach the element to the holder.
The ring with three holes on the tweeter element can be removed by
twisting CCW if you want to install in some other way.
FACTS ABOUT DLS UR1 TWEETER
Art.no
Size
Nom. power (RMS)
Freq. range
Sensitivity
Fs
Overall dimensions
Magnet
Mounting depth
Mounting hole
Cone material
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
DLS Svenska AB
SE-40251 Göteborg, Sweden
G
B
A
10-25401
28 mm
50 Watts (80 Watts max)
1 kHz-25 kHz
93 dB
900 Hz
62 mm / 2,44"
28 mm / 1,1" neodymium
26 mm / 1"
45 mm / 1,77"
Hand treated fabric
P.O. Box 13029
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
TWEETER INSTALLATION UP1C
UP1C can be installed on the dashboard with the angled cup or
recessed in a doorside with the flush cup.
UP1C are included in the UP5i, UP6i, UP35i and UP36i speaker kits.
SURFACE
MOUNTING:
For angled surface mount
together with the angled cup:
The
tweeter
attached to the cup by fitting
the three wings on the angled
cup into the tracks of the ele-
ment
and
clockwise. When removing the
element from the cup, turn it
ccw and lift it up.
RECESSED MOUNTING:
You need a hole with a diameter of 48 mm
C
/ 1,89" in the door side. Put the two metal
wings through the two tracks in the center
of the cup, just as the picture shows, and
D
attach them with the M4 screw and nut
through the center hole. The cup is
attached to the door side when the metal
wings is pressed to the back side of the
door.
Put the tweeter element into the cup with
the cable going out through the bottom
hole. Then attach the element into the cup
and turn it clockwise to attach to the cup.
When removing the element from the cup,
turn it ccw and lift it out
FACTS ABOUT DLS UP1C TWEETER
Size
Nom. power (RMS)
Freq. range
Sensitivity
Magnet diameter
Mounting depth
Mounting hole
Cone material
For technical assistance ask the shop where the product
was sold or the distributor in your very country.You can
always phone the DLS Helpdesk in Sweden + 46 31
840060 or send an e-mail to info@dls.e
Information can also be found on our WEB-site www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
element
is
then
turn
it
28 mm / 1,1"
50 Watts (80 Watts max)
1,5 kHz-20 kHz
93 dB
28 mm / 1,1"
18 mm / 0,71"
48 mm / 1,89"
Hand treated fabric
Technical Assistance
Advertisement
