Advertisement
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC
outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
A. Mounting the E-10A and E-10A-EWP
The E-10A and E-10A-EWP are designed to be flush mounted to the included 4" x 4" x 2" deep plastic rough in
box or surface mounted using an optional Viking model VE-5x5. Note: The E-10A and E-10A-EWP will NOT
mount to a standard double gang box. The plastic rough in box (part # 259576) may be purchased separately. Go
to www.vikingelectronics.com and click on "Spare Parts".
Front View of Plastic
Rough-In Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
5.22"
5.14"
Front View of Optional
2.25"
VE-5x5 (not included)
B. Mounting the E-20B and E-20B-EWP
The E-20B and E-20B-EWP are designed to be surface mounted to a single gang box (not included), a standard
4" x 4" electrical junction box (not included), or directly to a wall or flat sided post. Caution: For rough surfaces
(ie: brick, stucco, etc.) additional caulking may be required.
3.40"
1.55"
3.30"
3.40"
2.35"
C. Wiring
**** Note: When wires are routed
from above, a "drip loop" is recom-
mended to keep water away from the
circuit board.
* Gel-Filled Butt
Connectors
Red
(Ring)
**** Wires from
E-10A/E-10A-EWP
E-20B/E-20B-EWP
Green (Tip)
* Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum
insulation of 0.082 inches. Cut off stripped wire ends before terminating.
** Note: Talk battery must be a minimum of 28V DC when using the speaker phone with a Viking K-1900-5 Dialer (DOD# 317) or
K-1900-30 Multi-Number Dialer (DOD# 300).
*** Note: When installing a line powered phone on a low voltage and/or low loop current phone system extension, a Viking TBB-
2
1B Talk Battery Booster may be required, see DOD# 632.
4.0"
3.25"
(1) .74" dia
Condensation
Drain Hole
Rear View of VE-5x5 (not included)
Front view of the
E-20B and E-20B-EWP
Call
VIKING
©
To open the speaker box, remove the
two separate screws from the cover.
Viking C-200 or C-250 Single Entry
Phone Controller (not included)
VIKING
MODEL C-200
©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE ENTRY PHONE
CONTROLLER
1 2 3 4 5 6 7 8 9 10
ON
1
2
3
EARTH
C.O. LINE
OUT TO
ENTRY
GND
INPUT
PHONES
PHONE
-or-
To dedicated phone, unused trunk/line input of a phone system, or Viking C-1000B Doorbox Controller
Installation
2.1"
*
1/8" thick foam
gasket (included)
5.0"
Typical
Push to Call Button
(4) 6-32 X 3/4" stainless steel, flat
head, hexdrive, screws (included)
Condensation Drain Hole
(4) 0.38" diameter (for gooseneck mounting)
(4) 0.2 x 0.43 slots for double gang box
(2) 0.2 x 0.43 slots for single gang box
The optional VE-5x5 Surface Mount Box is de-
signed to be surface mounted to a single gang
3.0" 3.3"
box, double gang box or VE-GNP gooseneck
pedestal (shown right). For more information
on the VE-5x5 and VE-GNP, see DOD# 424.
3.0"
Back Panel of the
E-20B and E-20B-EWP
UP
Mount back panel to a wall, a single
gang box or a 4"x4" junction box with
the arrow pointing up. Note: For
outdoor applications apply a bead of
caulk between back panel and wall.
Viking C-2000B 1-4 Entry Phone
Controller (not included)
VIKING
MODEL C-2000B
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7
8 9 1 0 11 12 13
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
J7-
J8-
1
1
2
3
2
3
LED1
LED2
C
C
LED3
LED4
C
C
N.O. COM N.C.
AUX CONTACTS
PABX/KSU station
* Note: Peel off paper
liner and adhere gasket to
the back of the faceplate,
centering it over the four
corner mounting holes.
Caution: For rough sur-
faces (ie: brick, stucco,
etc.) additional caulking
may be required.
E-20B and E-20B-EWP
** Optional Viking
K-1900-5 Dialer or
K-1900-30 Multi-
Number Dialer
(not included)
VIKING
©
Programmable
Tone Dialer
MODEL: K-1900-5
Quick Programming Guide
1. Call the phone connected to the dialer.
∗
2. Answer phone. Enter
& security code.
(Factory set to 845464) Write your
security code below:
3. Enter your spped dial number & #00.
Note: For additional programming see
K-1900-5 Technical Practice.
J10-
J9-
J11-
1
3
Viking Electronics, Inc.
2
3
1
2
1
2
3
Hudson, WI 54016
LED5
C
LED6
C
LED7
C
LINE IN
PHONE
To C.O. Line or
E-10A shown with
Viking Model
VE-GNP
Gooseneck
Pedestal
Side view of the
Attach the cover to the
base with the two included
screws as shown.
*** C.O. Line or Analog
PABX/KSU Station
(programmed for ringdown)
Viking DLE-200B
Two Way Ringdown
Circuit (not included)
VIKING
RINGDOWN
©
DLE-200B
1
2
RES
BUSY
Advertisement
