Mp3/Wma; Playing Mp3/Wma Data; External Device; Turning Mute Mode On/Off - Alpine CDA-9847R Owner's Manual

MP3/WMA

Playing MP3/WMA Data

CDDA (Initial setting) / CDDA/MP3
This product can playback CDs containing both CD and MP3/WMA
data. However, in some situations (some enhanced CDs), playback
may be difficult. For these special cases, you can select playback of
CD data only. When a disc contains both CD or the MP3/WMA data,
playback starts from the CD data portion of the disc.
CDDA : Only CD data can be played back.
CDDA/MP3 : Both CD data and MP3/WMA file tracks can be
played back.
• Perform this setting before inserting a disc. If a disc has already
been inserted, perform the setting after you remove the disc.

External Device

Turning Mute Mode On/Off

MUTE ON (Initial setting) / MUTE OFF
If a device having the interrupt feature is connected, audio will be
automatically muted whenever the interrupt signal is received from
the device.

Setting the AUX Mode (V-Link)

AUX IN ON / AUX IN OFF (Initial setting)
You can input TV/video sound by connecting an optional Ai-NET/
RCA Interface cable (KCA-121B) or Versatile Link Terminal (KCA-
410C) to this component.
You can change the AUX name display when AUX ON is set. Select
the AUX name by pressing g or f. Then press BAND.
If the KCA-410C is connected, it is possible to select two AUX
names.
• Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/POWER to select AUX
mode and then press BAND to select your desired device.

Connecting to an External Amplifier

POWER IC ON (Initial setting) / POWER IC OFF
When an external amplifier is connected, sound quality can be
improved by stopping the power supply of the built-in amplifier.
POWER IC OFF : Use this mode when the front and rear pre-
amplifier of the unit are used to drive an
external amplifier connected to the
speakers. In this setting, the head unit's
internal amplifier has no output to drive
speakers.
Amplifier
Amplifier
20
-EN
• No sound is produced by the system when the power output is set to
OFF.

Setting the External Digital Input

D-AUX ON / D-AUX OFF (Initial setting)
When an ALPINE Ai-NET compatible digital audio processor and an
Ai-NET non-compatible DVD player (DVE-5207) are connected, set
D-AUX to ON to enjoy 5.1-channel surround sound.
• After setting D-AUX to ON, make the setting in "Connecting an
Optical Digital Compatible Audio Processor and an Ai-NET Non-
Compatible DVD Player."
• Press SOURCE/POWER, and select the D-AUX mode, and adjust
the volume, etc.
• Depending on the connected audio processor, DVD player sound
may continue to be output, even though the source is changed to
another one. If this occurs, set the DVD player's power to OFF.
Connecting an Optical Digital Compatible Audio
Processor and an Ai-NET Non-Compatible DVD Player
H510 /OTHER (Initial setting)
After setting D-AUX to ON in "Setting the External Digital Input," do
the following according to the audio processor type:
Front
left
Front
right
Rear
left
• After input selection is completed, turn the ignition off and back on
Rear
again. Setting of the optical digital input switch is completed.
right
POWER IC ON : The speakers are driven by the built-in
amplifier.
SPEAKER
RIGHT FRONT
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
H510 : If the PXA-H510 and the Ai-NET non-compatible
DVD player (DVE-5207) are connected (using optical
cable), use the H510 setting. Connect the DVD
player (using optical cable) to the optical digital
input terminal (for DVD Player).
OTHER: If an audio processor other than PXA-H510 and the
Ai-NET non-compatible DVD player (DVE-5207) are
connected (using optical cable), use the OTHER
setting. Connect the DVD player (using optical
cable) to the optical digital input terminal (for Head
unit).
Speakers
Front
right
Rear
right
Rear
left
Front
left