Table of Contents
Related Manuals for Miele T 4809 Ci
Summary of Contents for Miele T 4809 Ci
- Page 1 Operating instructions for condenser tumble dryer T 4809 Ci en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
-
Page 2: Caring For The Environment
Caring for the environment Disposal of the packing Energy saving tips material To avoid unnecessarily long drying times and high consumption of energy: The transport and protective packing has been selected from materials which – Make sure that your laundry is are environmentally friendly for disposal thoroughly spun before drying. -
Page 3: Table Of Contents
Contents Caring for the environment ......... . 2 Warning and Safety instructions . - Page 4 Contents Cleaning and care ..........22 Emptying the condensed water container .
- Page 5 Contents Fitting a door front panel made by another manufacturer ....41 Preparing the front panel ......... 41 Preparing the fixing points .
-
Page 6: Warning And Safety Instructions
Any other applications may be dangerous. Miele cannot be held liable To avoid the risk of accidents and for damage resulting from incorrect or damage to the tumble dryer, please improper use or operation. - Page 7 Do not install or use a damaged tumble dryer. If the connection cable is faulty it must only be replaced by a Miele Before connecting the tumble dryer, approved service technician to protect ensure that the connection data on the the user from danger.
-
Page 8: Correct Use
Warning and Safety instructions Correct use To prevent the risk of fire, the following must not be dried in this To prevent the risk of fire, the tumble dryer: following textiles must not be dried in this tumble dryer: – items which have been cleaned using chemicals (e.g. - Page 9 / or condensed Accessories water container. The ambient room temperature should Only use genuine Miele spare parts be between +2°C and +35°C. and accessories with this appliance. If non-Miele parts are used, guarantee, If the water is drained externally...
-
Page 10: Operating The Tumble Dryer
Operating the tumble dryer Control panel Low temperature button Check lights Delicate fabrics are dried at a lower For a description of these lights see: temperature. "Problem solving guide" / "After sales service". Drying level button Start/Stop button with indicator lights For starting the programme selected Display and cancelling a programme once it... - Page 11 Operating the tumble dryer Display In the same way, the Woollens handcare, Silks handcare and The following are selected via the Smoothing programmes can finish display: earlier than expected if a certain – Delay start temperature is reached. This can happen with particularly fine fabrics, –...
-
Page 12: Notes On Laundry Care
Notes on laundry care Care symbols – Down-filled garments have linings which have a tendency to shrink, Before drying check the drying symbol depending on the quality of the item. on the care label. If there are no They can be partially dried using the symbols, dry at your own risk! Smoothing programme. -
Page 13: How To Dry Correctly
How to dry correctly Brief instructions Load the tumble dryer ^ Press the Door button to open the The headings numbered ( , ...) show the operating sequence and can door. be used as a brief guide to using your ^ Load the laundry loosely into the dryer. - Page 14 How to dry correctly Select a programme Important: Please note that the programme duration shown in the display will vary according to the programme selected (see "Programme duration/Estimated time remaining"). The Woollens handcare, Silks handcare and the Smoothing programmes cannot be changed.
- Page 15 How to dry correctly Start the programme Remove the laundry when the programme has finished The Start/Stop button will flash when a programme is being selected. The 0 and Finish will appear in the display flashing indicates that a programme to indicate that the programme has can be started.
-
Page 16: Extra Options / Delay Start
Extra options / Delay start Low temperature – If you keep the Delay start button pressed in, the time will continue to increase up to 24^. For all delicate or minimum iron fabrics with the r symbol on the To begin delay start care label (e.g. -
Page 17: Programme Chart
Programme chart Cottons Max. load 6 kg* Extra dry, Normal** Fabric type Single and multi-layered cotton fabrics such as towelling, jerseywear, T-shirts, underwear. Notes – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for loopknit fabrics (e.g. T-shirts, underwear), as they have a tendency to shrink. -
Page 18: Smoothing
Programme chart Woollens handcare Max. load: 2 kg* Fabric type Woollen fabrics Note – This programme only fluffs up woollen garments. – Fabrics are not completely dried in this programme. Remove garments as soon as the programme has finished and leave to finish drying at room temperature. Low temperature Low temperature cannot be deselected. -
Page 19: Outerwear Normal
Programme chart Automatic Max. load: 3.5 kg* Normal, Hand iron Fabric type Mixed loads of garments suitable for the Cottons and Minimum iron programmes. Sort according to colour. Shirts Max. load: 2 kg* Normal, Hand iron Fabric type Shirts and blouses. Low temperature Select the Low temperature option for delicate fabrics with the r symbol on the care label. -
Page 20: Changing The Programme Sequence
Changing the programme sequence Once a programme has started Altering Delay start ^ See "Delay start". - changing the programme You cannot change to another Adding or removing laundry programme once a programme has after a programme has started started (this prevents unintentional ^ Press the Door button. -
Page 21: Electronic System Lock
Electronic system lock Now slowly turn the programme The system lock prevents the dryer selector six positions stage by stage being used without your knowledge. in an anti-clockwise direction. Each of the six programme indicator It can be activated if wished. lights must come on one after the other. -
Page 22: Cleaning And Care
Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose (see "Installation"). Empty the condensed water container after every drying programme. The Empty out container indicator light will come on if the maximum level of the condensed water container is reached. -
Page 23: Cleaning The Fluff Filters
Clean your Miele dealer or the Miele Spare the filters after each drying Parts Department, or use a vacuum programme*. -
Page 24: Cleaning Them With Water
Cleaning and care Cleaning them with water Do not replace them if they are If there is a great deal of compacted damp or wet. Damp or wet filters fluff on any of the filters, they can be could cause operational faults. removed and cleaned under hot ^ Push the large filter back into the running water. -
Page 25: Cleaning The Tumble Dryer
Cleaning and care Cleaning the tumble dryer Disconnect the tumble dryer from the mains electricity supply. Miele branded cleaning and conditioning products are available to order via the internet on www.miele-shop.com. ^ Clean the housing and control panel with a slightly damp cloth and a mild detergent or soapy water. -
Page 26: Cleaning The Condenser Unit
Cleaning and care Cleaning the condenser unit Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit. Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage. -
Page 27: Checking The Condenser Unit
Cleaning and care If you cannot see any fluff: ^ Replace the condenser unit (see following page). If you can see some fluff: ^ Clean the condenser unit as described below. Cleaning the condenser unit ^ When rinsing the condenser unit, make sure you position it as shown in the next two illustrations. -
Page 28: Replacing The Condenser Unit
Cleaning and care Replacing the condenser unit ^ With the handle facing upwards, push the condenser unit back into position in its housing. ^ Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove. When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove. -
Page 29: Problem Solving Guide
Cooling down or and then on again. Finish flashes in the – Then start the display. programme again. The buzzer sounds. If the programme stops again and Cooling down or Finish flashes again, there is a fault. Contact the Miele Service Department. - Page 30 – Then start the programme The buzzer sounds. again. – If the Clean out airways indicator light comes on again, contact the Miele Ser- vice Dept. The Empty The condensed water – Empty out the condensed container indicator container is full or there water container.
-
Page 31: Other Problems
Problem solving guide Other problems Problem Possible cause Remedy The drying Please check all the possible causes and switch the dryer process goes off and then back on again. on too long or Ventilation to and from the dryer Open a door or window while even switches may be insufficient (e.g. - Page 32 Problem solving guide Problem Possible cause Remedy Water leaks from the – The inner cover of the – Ensure that the dryer after the condenser unit has not condenser unit is condenser unit has been locked properly positioned correctly been cleaned. and/or the condenser and lock the inner unit has not been...
- Page 33 Problem solving guide Problem Possible cause Remedy The tumble dryer fails to No obvious cause. – Is the dryer switched start when switched on. – Is the plug correctly inserted into the socket and switched on? – Is the door closed properly? –...
-
Page 34: Changing The Lamp
^ Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover. The cover will open downwards. The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department. -
Page 35: After Sales Service
Optional accessories Optional accessories for this dryer are available from your Miele Dealer, the Miele Spare Parts Department or via the internet at www.miele-shop.com. Please note that telephone calls may be monitored and recorded for training purposes. -
Page 36: Installation
Installation Front view Mains connection cable Four height adjustable screw feet Condensed water container External drainage options (e.g. via wash basin, wash basin drain outlet Control panel or gully) Door (can be fitted with a decor panel) Service panel for condenser unit... -
Page 37: Installation Site
Installation Installation site Make sure the dryer door can be opened without hindrance after installation. Building under a continous worktop / in a kitchen run This tumble dryer is specially designed for installation under a continuous worktop run in a fitted kitchen. –... -
Page 38: Aligning The Appliance
Washer-dryer stack The tumble dryer can also be combined with a Miele washing ^ Turn the 4 screw feet to adjust the machine in a washer-dryer stack. To do dryer to the correct height and level. -
Page 39: Matching The Fascia Panel To The Height Of Adjacent Drawer Fronts
Installation Matching the fascia panel to Removing the spacer bars the height of adjacent drawer All the spacer bars can be removed if fronts the upper edge of the front panel needs to be flush with the upper edge of the The fascia panel can be aligned with appliance front directly underneath the the drawer fronts by adjusting the... -
Page 40: Fitting The Front Panel
^ Hold the front panel in the correct position in front of the appliance If fitted in a Miele kitchen, the door panel can be ordered pre-drilled with the necessary fixing holes. If fitted in a non-Miele kitchen, a suitable panel will have to be drilled to suit by a qualified kitchen fitter. -
Page 41: Fitting A Door Front Panel Made By Another Manufacturer
Installation Fitting a door front panel made Mark the two hinge holes and the four smaller holes as shown in the by another manufacturer diagram. Preparing the front panel For left hand hinging only: Measure distance X for drilling the –... -
Page 42: Preparing The Fixing Points
Installation For right hand hinging only: Drill the two hinge holes (C 35 mm/15.5 mm deep) in the back of – front panel shown decor side face the front panel. down, upper edge at the bottom: Next, drill the four smaller holes (C 7 mm/10 mm deep) in the back of the front panel. -
Page 43: Fitting A Plinth Facing
Installation Fitting a plinth facing Useful tip: The gap between the lower edge of the If the dryer is fitted on a raising kit, you tumble dryer plinth and the floor can be can use double-sided adhesive tape on closed up using a suitable kitchen the back of the plinth facing to secure it furniture plinth facing. -
Page 44: External Condensed Water Outlet
Installation External condensed water outlet General notes When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the dryer is installed near a sink, drain outlet etc. -
Page 45: External Drainage Via A Sink Or Gully
Installation External drainage via a sink or gully Example: Connection to a sink drain outlet ^ See "Front view" illustration. The drain hose with non-return valve If you want to drain the water off fitted can be connected directly to a into a sink you will need to secure suitable sink drain outlet. - Page 46 Installation ^ Fit adapter 1 to the sink drain outlet using nut 2. If this nut has a flat disc in it you should take the disc out first. ^ Attach the end of the extension hose 4 to adapter 1. ^ Use a screwdriver to tighten hose clip 3 up close to the nut.
-
Page 47: Electrical Connection
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out The fuse cover must be refitted when by a suitably qualified and competent changing the fuse, and if the fuse cover person, in strict accordance with is lost, the plug must not be used until a current national and local safety suitable replacement is obtained. -
Page 48: Consumption Data
Consumption data Programme Load Final spin speed Energy Duration in a domestic washing machine Minutes Cottons 1000 (60 % residual moisture)** 3.35 Normal 1200 3.05 1400 2.90 1600 2.55 1800 2.50 Cottons 1000 (60 % residual moisture)** 2.65 Hand iron 1200 2.35 1400... -
Page 49: Technical Data
Technical data Height 820 mm Width 595 mm Depth 575 mm Suitable for stacking Weight 54 kg Drum volume 100 litres Maximum capacity 6 kg dry weight Capacity of condensed water container approx. 3.5 litres Drain hose length 950 mm Maximum delivery head 1.5 m Maximum drain hose length... -
Page 50: Programmable Functions For Changing Default Settings
Programmable functions for changing default settings The programmable functions are used to alter the tumble dryer´s electronics to suit changing requirements. Programmable functions can be altered at any time. -
Page 51: Programmable Functions
Programmable functions Extending the range of the – The Low temperature indicator light will briefly flash on and off twice. drying levels – P and 0 (default setting) will flash You can extend the range of the alternately in the display. drying levels for many of the The number which appears alternately programmes:... -
Page 52: Altering The Volume Of The Buzzer
Programmable functions Altering the volume of the Press the Start/Stop button and keep it pressed in whilst carrying out steps buzzer The buzzer has two volumes. Press the I-On/0-Off button in. Follow steps to programme Wait until the indicator light for the and store in memory. -
Page 53: Memory Function
Programmable functions Memory function Press the Start/Stop button and keep it pressed in whilst carrying out steps The electronics will memorise any extra options selected for a Press the I-On/0-Off button in. programme. The duration selected for a timed Wait until the indicator light for the drying programme will also be stored Start/Stop button lights up in memory. -
Page 54: Extending The Cooling Down Time
Programmable functions Extending the cooling down Press the Start/Stop button and keep it pressed in whilst carrying out steps time The cooling down phase which takes Press the I-On/0-Off button in. place before the end of a programme Wait until the indicator light for the can be lengthened if required. -
Page 55: Clean Out Airways Indicator
Programmable functions Clean out airways indicator Press the Start/Stop button and keep it pressed in whilst carrying out steps Fluff should be removed after drying. The Clean out airways indicator will Press the I-On/0-Off button in. remind you to clean the filters when a Wait until the indicator light for the certain amount of fluff has collected Start/Stop button lights up... -
Page 56: Keypad Tone
Programmable functions Keypad tone Press the Start/Stop button and keep it pressed in whilst carrying out steps An audible tone sounds each time a button is pressed. Press the I-On/0-Off button in. Follow steps to programme Wait until the indicator light for the and store in memory. -
Page 57: Adjusting The Dryer's Electronics For Very Soft Water
Programmable functions Adjusting the dryer's Press the Start/Stop button and keep it pressed in whilst carrying out steps electronics for very soft water Extremely soft water can affect Press the I-On/0-Off button in. the sensitivity of the control Wait until the indicator light for the electronics. - Page 60 Alteration rights reserved/3809 M.-Nr. 06 984 111 / 03...