Table of Contents
Related Manuals for Miele G 1021
Summary of Contents for Miele G 1021
-
Page 1: Operating Instructions
Operating instructions for dishwashers To avoid the risk of accidents or en - GB damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. M.-Nr. -
Page 2: Table Of Contents
Contents Guide to the appliance ..........5 Appliance overview . - Page 3 Contents Operation ............31 Detergent .
- Page 4 Plumbing............58 The Miele waterproof anti-leak system ....... . . 58 Connection to the water supply .
-
Page 5: Guide To The Appliance
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Child safety lock in door grip (not visible) d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent... -
Page 6: Control Panel
This instruction book applies to several different dishwasher models. The specific dishwasher models below are referred to as follows: G 1021, G 1022 etc. = G 1XXX G 2021, G 2022 etc. = G 2XXX The model numbers G 1XXX and G 2XXX used in this book refer to the model designation specified on the data plate of the appliance (and not the description on the control panel). -
Page 7: Warning And Safety Instructions
Warning and Safety instructions Safety with children This appliance conforms to current This appliance is not a toy! To avoid safety requirements. Inappropriate the risk of injury, keep children well use can, however, lead to personal away and do not allow them to play in injury and damage to property. - Page 8 Warning and Safety instructions Technical safety Do not connect the dishwasher to the mains supply until it has been fully Before setting up the appliance, installed. check it for any externally visible damage. Under no circumstances Before connecting the appliance, should you use a damaged appliance.
- Page 9 If the connection cable is damaged where necessary. it must be replaced with a Miele cable – The stopcock has been turned off by a Miele approved service technician when the appliance is not used for a only.
-
Page 10: Correct Use
Warning and Safety instructions Installation Correct use The dishwasher must be installed Do not use solvents in the and connected in compliance with the dishwasher. Danger of explosion. installation diagram supplied. Do not inhale or ingest dishwasher The dishwasher must be correctly detergent. - Page 11 Warning and Safety instructions Accessories Inadvertently filling the salt reservoir with powder or liquid dishwasher Only use genuine Miele spare parts detergent will damage the water and accessories with this appliance. If softener. Make sure you have picked spare parts or accessories from other...
-
Page 12: Caring For The Environment
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for disposal human health and to the environment. -
Page 13: Energy Saving Washing
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your water supply is suitable, this dishwasher can be connected to hot water for further economies. -
Page 14: Before Using For The First Time
Before using for the first time To open the door Safety lock ^ Press the release catch inside the Use the safety lock to prevent children door grip upwards and pull the door opening the dishwasher door. open. ^ To lock the door, push the slide If the door is opened during operation underneath the door grip to the right. -
Page 15: Water Softener
Before using for the first time Water softener The dishwasher is set at the factory for a hardness level of In order to achieve good cleaning 2.2 - 2.7 mmol/l (12 - 15 °d ). results, the dishwasher needs to operate with soft water. -
Page 16: To Programme The Water Hardness Level
Before using for the first time To programme the water hardness The number of times the programme sequence indicator flashes tells you the level water hardness level which has been Each time a button is pressed, one of set (see chart). the indicator lights will flash and light up in the control panel. -
Page 17: Checking The Programmed Water Hardness Level
Before using for the first time Checking the programmed water hardness level ^ Switch the dishwasher off using the K button. ^ Turn the programme selector to the "12 o'clock" position. ^ Press the Start/Stop button J / M in, and whilst holding it in switch the dishwasher on using the K button. -
Page 18: Before Using The Appliance For The First Time You Require
Before using for the first time Miele branded products are available Important Before filling the salt from the Miele Spare Parts reservoir with dishwasher salt for the Department or via the internet at first time, you must fill it with www.miele-shop.com. -
Page 19: Salt Refill Indicator F
Before using for the first time Salt refill indicator F ^ Remove the lower basket and unscrew the salt reservoir cap. ^ Fill the salt reservoir with dishwasher salt when the salt refill indicator F Only open the salt reservoir when comes on. -
Page 20: Rinse Aid
Before using for the first time Rinse aid If you only ever use combination Rinse aid is necessary to ensure water products containing rinse aid in your does not cling and leave marks on dishwasher, you do not need to add crockery during the drying phase and rinse aid. -
Page 21: Rinse Aid Indicator
Before using for the first time Rinse aid indicator When the rinse aid indicator comes on, the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. ^ Add rinse aid only until it is visible in the opening. -
Page 22: Setting The Rinse Aid Dosage
Before using for the first time ^ Turn the programme selector to the Setting the rinse aid dosage "5 o'clock" position. You can adjust the rinse aid dosage for best results. programme sequence indicator will flash briefly three times at intervals. The rinse aid dosage can be set from This means that approx. -
Page 23: Loading The Dishwasher
Loading the dishwasher Note – Wide based items should be placed at an angle so that water can run off Remove coarse food residues from them freely. crockery. – The spray arms must not be blocked There is no need to rinse items under by items which are too tall or hang running water. -
Page 24: Items Not Suitable For Dishwashers
Loading the dishwasher Items not suitable for We recommend: dishwashers: – When purchasing new crockery and cutlery, make sure they are – Wooden cutlery and crockery or dishwasher-proof. items with wooden parts: these may discolour and fade. The glue used in –... -
Page 25: Upper Basket
Loading the dishwasher Upper basket Hinged cup rack ^ To make room for tall items, raise the For safety reasons, do not rack upwards. operate the dishwasher without the upper and lower baskets in place. Positioning rail (depending on model) Glasses can be arranged along the positioning rail to give them some support during the programme. -
Page 26: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or upper basket, the upper basket can be Dishwasher with cutlery tray adjusted on three levels with 2 cm (see data plate for model number) -
Page 27: Lower Basket
Loading the dishwasher Lower basket Hinged spikes ^ For larger and heavier items such as The spikes are used for washing plates plates, serving platters, saucepans, and saucers. bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place delicate glassware in the lower basket. -
Page 28: Removable Spiked Insert
Loading the dishwasher Removable spiked insert Bottle holder (depending on model) You can remove the spiked insert to The bottle holder can be used to wash make more room for larger items of narrow items, e.g. milk and baby crockery, e.g. a large, flat pot, or bottles. -
Page 29: Cutlery
Loading the dishwasher Cutlery Cutlery tray (depending on model) If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 30: Cutlery Basket (Depending On Model)
Loading the dishwasher Cutlery basket (depending on model) ^ Fit it into the cutlery basket if required. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. -
Page 31: Operation
Combi tabs are available as "3 in 1" or, Miele branded dishwasher cleaning when they also contain other components products are available from the Miele such as glass and stainless steel Spare Parts Department or via the protective additives and enhanced Internet at www.miele-shop.com. -
Page 32: Adding Detergent
Operation The flap is always open at the end of a Avoid inhalation of powder programme. detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. -
Page 33: Switching On
Operation Switching on Starting a programme ^ Make sure the spray arms are not ^ Turn the programme selector obstructed. clockwise or anti-clockwise to the required programme. ^ Close the door. The J / M indicator light will flash. ^ Open the stopcock, if it is closed. ^ Press the J / M button. -
Page 34: At The End Of A Programme
Operation At the end of a programme Unloading the dishwasher The O programme sequence indicator Dishes tend to break and chip more will light up when the programme is easily when they are hot. finished. Allow the dishes to cool until they are comfortable enough to handle before The dishwasher can now be opened unloading them. -
Page 35: Interrupting A Programme
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as If the detergent dispenser flap has the door is opened. already opened, do not change the When the door is closed again, the programme. programme will continue from the point it was at before the door was opened. -
Page 36: Additional Functions
Operation Additional functions programme sequence indicator light shows whether a setting other than Factory default setting the factory default setting has been set. – If the programme sequence If you have altered any settings from the factory default, you can re-set them indicator light is flashing: back to the factory default settings as All settings are factory default... -
Page 37: Cleaning And Care
The external surfaces of the surface to alter or discolour. dishwasher are susceptible to scratching. ^ Clean the front using a damp Miele Contact with unsuitable cleaning microfibre E-cloth or with a sponge and agents can alter or discolour the a solution of hot water and washing-up outer surfaces. -
Page 38: Cleaning The Filters In The Wash Cabinet
Cleaning and care Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. The dishwasher must not be used without all the filters in place. - Page 39 Cleaning and care ^ Replace the filter combination so that To clean the inside of the filter, the flap must be opened: it lies flat in the base of the wash cabinet. ^ Press catches a together in the ^ Then turn the handle clockwise, until direction of the arrows as shown, and open the filter b.
-
Page 40: Cleaning The Spray Arms
Cleaning and care ^ Remove the lower basket. Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. -
Page 41: Problem Solving Guide
Problem solving guide With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations. - Page 42 Problem solving guide Problem Possible cause Remedy , G and O There may be a technical – Clean the water inlet filter programme sequence fault. and clean the drain pump indicator lights flash and non-return valve as simultaneously. described in "Maintenance".
-
Page 43: The Dishwasher Does Not Fill/Drain
Problem solving guide The dishwasher does not fill/drain. Problem Possible cause Remedy The 2 / 2 check The stopcock is Open the stopcock fully. light flashes. closed. The dishwasher Before rectifying the problem you stops during a must: programme. – Switch the dishwasher off The 2 / 2 check using the K button. -
Page 44: General Problems
Problem solving guide General problems Problem Possible cause Remedy Detergent residue is left The dispenser was still Make sure the dispenser is in the dispenser at the damp when detergent dry before adding end of a programme. was added. detergent. The detergent Clogged detergent Clean the detergent from... -
Page 45: Noises
Problem solving guide Noises Problem Possible cause Remedy Knocking noise in the A spray arm is knocking Interrupt the programme, wash cabinet. against an item in a and rearrange the items basket. which are obstructing the spray arm. Items of crockery are Interrupt the programme, Rattling noise in the wash cabinet. -
Page 46: Unsatisfactory Washing Result
Problem solving guide Unsatisfactory washing result Problem Possible cause Remedy The dishes are not The dishes were not loaded See notes in "Loading the clean. correctly. dishwasher" The programme was not Select a more intensive powerful enough. programme. See Programme chart. - Page 47 Problem solving guide Problem Possible cause Remedy Dishes, cutlery The amount of rinse aid Replenish the reservoir, and glasses are may be insufficient, or the increase the dosage or not dry or are rinse aid reservoir empty. change the brand of rinse aid. flecked.
- Page 48 Problem solving guide Problem Possible cause Remedy Glassware has a This may be caused by the Change your detergent. brown or blue tinge, detergent. and film cannot be wiped off. Glassware is dull and The glasses are not There is no remedy. discoloured;...
-
Page 49: Maintenance
^ Replace the filter and seal, making union. This filter is available from the Miele Spares Parts dept. sure they are sitting correctly. ^ Reconnect the inlet hose to the Cleaning the filter:... -
Page 50: Cleaning The Drain Pump And Non-Return Valve
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. -
Page 51: After Sales Service
– Your Miele dealer, or technology. – the Miele Service Department (see Information regarding programme back cover for address). updates will be made known by the Miele Company as and when such Please note that telephone calls may developments become available. -
Page 52: Programme Chart
Programme chart Crockery Food deposits Action required Mixed, All normal This needs an everyday crockery food deposits adaptable programme Heat-sensitive glasses and plastic Fresh, This needs a short easily removed programme... food deposits Mixed crockery This needs a standard programme... Normal food deposits which have begun to dry To save water and... - Page 53 Programme chart Programme Detergent Compartment I Compartment II 25 ml Sensor wash 55-65° – 1 tab 25 ml Quick wash 40°C – 1 tab 25 ml Light soiling 50°C – 1 tab 25 ml Energy save – 1 tab 25 ml Pots &...
- Page 54 Programme chart Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying °C °C Sensor wash Variable programme sequence, 55-65 °C sensor controlled adjustment according to the amount of crockery and level of food deposits If required 55-65 If required Pots &...
- Page 55 Programme chart Consumption Duration Energy Water Cold Litres Cold water water water water connection connection connection connection (15 °C) (55 °C) (15 °C) (55 °C) h:min h:min 1.30-1.60 0.75-1.00 13-22 1:45-2:30 1:35-2:16 1.70 1.20 2:39 2:29 1.05 0.70 2:54 2:44 0.02 0.02 0:12...
-
Page 56: Optional Accessories
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.miele-shop.com (some may be supplied as standard, depending on model). If you would like to …... -
Page 57: Electrical Connection
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 The fuse cover must be refitted when All electrical work must be changing the fuse, and if the fuse cover carried out by a suitably qualified is lost, the plug must not be used until a and competent person, in suitable replacement is obtained. -
Page 58: Plumbing
30 and 1000 kPa (0.3 and 10 bar). Providing your dishwasher has been If the water pressure is too high, a installed correctly, the Miele waterproof pressure reducer valve must be anti-leak system will protect you from fitted. water damage throughout its lifetime. -
Page 59: Drainage
Plumbing Drainage Venting the drainage system – The appliance drainage system is If the on-site drain connection is fitted with a non-return valve, which situated lower than the guide path for prevents dirty water from flowing the bottom basket rollers in the open back into the dishwasher via the door, the drainage system must be drain hose. -
Page 60: Technical Data
Technical data Dishwasher model G 1XXX G 2XXX Height freestanding 84.5 cm (adjustable +3.5 cm) Height built-in 80.5 cm 84.5 cm (adjustable + 6.5 cm) (adjustable + 6.5 cm) Height of building-in Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) recess Width 59.8 cm... - Page 64 Alteration rights reserved/ M.-Nr. 07 502 050 / 01 G1021/G1022/G2021/G2022 / 0410...