LG LM40 Service Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Laptop
  5. LM40
  6. Service manual

LG LM40 Service Manual

15”/14.1”
Hide thumbs Also See for LM40:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Service Manual
(LM40/50)
LG Electronics
0

Advertisement

Table of Contents
loading

Related Manuals for LG LM40

Summary of Contents for LG LM40

  • Page 1 Service Manual (LM40/50) LG Electronics...

  • Page 2: Table Of Contents

    Contents Ch 1. Service information Ch 2. Locations Ch 3. System information · Specification · Model configuration System Block Diagram · Fn key combinations · Status indicators · BIOS Flash · BIOS Setup · Ch 4. Symptom-to-part index Power system checkout ·...

  • Page 3: Ch1. Service Information

    Ch1. Service information Chapter 1. Service information 1-1. Important service information Strategy for replacing parts (FRU-Field Replaceable Units) Before replacing parts Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this Use the following strategy to prevent unnecessary expense for replacing and servicing parts 1.
  • Page 4 Ch1. Service information 1-2. Safety notices Warning Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
  • Page 5 Ch1. Service information 1-3. Safety information General safety Follow these rules to ensure general safety · Observe good housekeeping in the area of the machines during and after maintenance. · When lifting any heavy object 1. Ensure you can stand safely without slipping. 2.
  • Page 6 Ch1. Service information Electrical safety Observe the following rules when working on electrical equipment. Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
  • Page 7 Ch1. Service information · Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. · Observe the special safety precautions when you work with very high voltages. These instructions are in the safety sections of maintenance information.
  • Page 8 Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-LG alterations. Use good judgment as to the safety of any non-LG alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
  • Page 9 Ch1. Service information Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
  • Page 10 Ch1. Service information 1-4. Laser compliance statement When a CD-ROM drive, DVD drive or the other laser product is installed, note the following : Caution Use of controls or adjustments or performance of procedures other than those specified here in might result in hazardous radiation exposure.
  • Page 11 1-6. Read this first Before you go to the checkout guide, be sure to read this section. Important Notes Only trained personnel certified by LG should service the computer. · Read the entire FRU removal and replacement page before replacing any FRU.
  • Page 12 Ch1. Service information The followings are not covered under warranty : CD panel cracked from the application of excessive force or from being dropped · Scratched (cosmetic) parts · Distortion, deformation, or discoloration of the cosmetic parts · Cracked or broken plastic parts, broken latches, broken pins, or broken connectors caused by excessive ·...

  • Page 13: Ch2. Locations

    Ch2. Locations Chapter 2. Locations Front view (15”) Volume Up Volume Down Power switch Power-saving mode switch Keyboard TouchPad TouchPad button Built-in speakers IrDA port Front view (14.1”) Volume Up Volume Down Power switch Power-saving mode switch Keyboard TouchPad TouchPad button Built-in speakers IrDA port...
  • Page 14 Ch2. Locations Rear view (15”/14.1”) Ethernet port Power jack Modem port S-Video Left view (15”/14.1”) ODD tray open button IEEE1394 port SD memory Card slot PC card eject button PC card slot Emergency eject hole USB port Right view (15”/14.1”) Fan louvers Parallel port VGA port...

  • Page 15: Ch3. System Information

    Ch3. System information Chapter 3. System information Specification • CPU · Banias 1.3 ~ 1.7 GHz / Dothan 1.7 GHz · FCPGA • Main Chipset & Graphic · Intel ODEM + ICH4 · Intel Montara GME (Graphic Controller Integrated) · ATi M9+ w/32MB VRAM ·...

  • Page 16: Model Configuration

    Ch3. System information Model Configuration...

  • Page 17: System Block Diagram

    Ch3. System information System Block Diagram...

  • Page 18: Fn Key Combinations

    Ch3. System information Fn key combinations The following table shows the function of each combination of Fn with a function key. Function of Fn keys has nothing to do with Operating System. Description User-defined Hot key. (Setting is available at OSD) User-defined Hot key.

  • Page 19: Status Indicators

    Ch3. System information Status indicators · The system status indicators show the status of the computer. 14.1” 15” a. AC Power Power indicator lights up when the power cord is connected to the computer. b. Battery Battery status indicator indicates the following status of the battery. Green : The computer is connected to an AC adapter and is being charged.

  • Page 20: Bios Flash

    Ch3. System information BIOS Flash You can update BIOS using a floppy disk drive. Because this system is not equipped with any floppy disk drive, you have to use an external USB drive for a BIOS update. In order to boot up with an USB drive, please set Removable Device as the first boot up drive in the boot menu of BIOS setup.
  • Page 21 Ch3. System information How to update flash ROM in Windows 1. Quit all running programs. 2. Start WINPHLASH.EXE. 3. Select the procedure you want : a. Backup BIOS and Flash BIOS with new settings b. Backup BIOS Only 4. Specify the locations for backup and new BIOS files in BIOS Setting Locations. a.
  • Page 22 Ch3. System information 8. After the completion, ‘System BIOS was successfully updated’ appears on the screen, then the computer restarts. 9. After the restart, make sure the system BIOS is updated. 10. If your computer does not restart automatically, turn off your computer and then turn it back on by pressing power button.

  • Page 23: Bios Setup

    2. to replace the backup battery 3. system configuration error occurs 4. to change the boot order 5. to set/change a password Press the power button. When the LG logo appears on the screen, press and enter the BIOS Setup Utility.
  • Page 24 Ch3. System information Default screen · BIOS Setup Utility menu bar shows the following menus Main, Advanced, Security, Boot, Exit · Main menu enables you to set the system time and date, hard disk drive setup, memory configuration, and floppy disk drive specification. ·...
  • Page 25 Ch3. System information Using the keys The keys used in the BIOS Setup Utility and their functions are described at the bottom. · : General Help Display the descriptions of the keys used in the setup utility. · : Select Item Navigate and select items in the setup utility.
  • Page 26 Ch3. System information Main Menu · System Time Set the system time. Use Tab key to move to hour, minute, and second. Use +, -, or Spacebar to change the values. · System Date Set the system date. · Processor Type / Speed Indicate CPU type and clock speed installed on the system.
  • Page 27 Ch3. System information Advanced Menu · Legacy USB Support Enable support for the Legacy USB. (Enabled / Disabled) · TouchPad Support Enable support for TouchPad. (Enabled / Disabled) · Internal Keypad Enable support for the internal keypad. (Enabled / Disabled)
  • Page 28 Ch3. System information · Parallel Port Configure the parallel port using options. (Enabled / Disabled) Set the mode for the parallel port using options. (Output only, Bi-directional, EPP, and ECP) Set the base I/O address for the parallel port. (378 / 278 / 3BC) Set the interrupt for the parallel port.
  • Page 29 Ch3. System information Security Menu · Setting a password If you want to protect the system setup from an unauthorized user, follow the instructions below to set a password. You can set a password in the BIOS Setup Utility program. Caution If you forget the password, you cannot gain access to your system.
  • Page 30 Ch3. System information Note A supervisor password enables you to change settings in the BIOS Setup Utility and to perform Power on Boot. Users other than the administrator should only have user passwords. c. If the following message appears, enter a new supervisor password and then Enter. A password must be consisted of character A~Z and numbers 0~9, and have the maximum length of 8.
  • Page 31 Ch3. System information · Set User Password A user password provides a lower level of security compared to a supervisor password. A supervisor password must be set in order for you to set a user password. a. Start the BIOS Setup Utility and use arrow keys to select Security menu. b.
  • Page 32 Ch3. System information d. If the following message appears, press Enter. e. Press F10 to save the new settings. f. If the following message appears, select Yes and press Enter to restart the computer.
  • Page 33 Ch3. System information · Password on boot Enables password entry on boot a. Start the BIOS Setup Utility and use arrow keys to select Security menu. b. If the following screen appears, select Set Supervisor Password or Set User Password by using arrow keys, and input new password.
  • Page 34 Ch3. System information c. Select Password on boot menu, then change value (Enabled) by using +, - keys. Note If you set a Supervisor Password or User Password, you can use Password on boot. If you set Disabled on Password on boot, You don’t have to enter a password.
  • Page 35 Ch3. System information · Set HDD Password Set HDD Password to control access to the Hard-disk. Press Enter to input, change or disable hard-disk password. a. Start the BIOS Setup Utility and use arrow keys to select Security menu. b. If the following screen appears, select Set HDD Password by using arrow keys, and press Enter. Note When loosing your HDD Password, you can not access your Hard-disk drive.
  • Page 36 Ch3. System information c. If the following message appears, enter a new supervisor password and then press Enter. A password must be consisted of numbers 0~9, and have the maximum length of 8. d. If the following message appears, press Enter. e.
  • Page 37 Ch3. System information · Changing or removing a password You must know the password in order to change or remove it. a. Start the BIOS Setup Utility, enter your password, and then press Enter. b. To change the password, follow the instructions on Set Supervisor Password or Set User Password.

  • Page 38: Boot Menu

    Ch3. System information Boot Menu · Boot menu enables you to set the boot order for the CD-ROM drive, Removable devices, Hard drive, and Network boot. Boot menu displays the boot order of your system with higher priority given to a device higher on the list. The default boot order is CD-ROM drive, Removable devices, Hard drive, and Network boot.
  • Page 39 Ch3. System information Exit Menu · Exit System Setup and save your changes to CMOS. · Exit Saving Changes Select Exit Saving Changes to save new setup information in CMOS RAM. CMOS RAM stores the information using the backup battery; there fore, the information will not be lost when the computer is turned off.
  • Page 40 Ch3. System information · Discard Changes Select Discard Changes to discard new setup information. Setup Confirmation asks you to confirm your selection. If you want to discard any new setup information, select Yes. · Save Changes Select Save Changes to save any new setup information without exiting the BIOS Setup Utility. Select Yes to save the new setup information in the Setup Confirmation window.

  • Page 41: Ch4. Symptom-To-Part Index

    Ch4. Symptom-to-part index Chapter 4. Symptom-to-part index The symptom-to-part index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first. Note If replacing a part (FRU) does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.
  • Page 42 Ch4. Symptom-to-part index · If the voltage is not correct, replace the AC adapter. · If the voltage is acceptable, do the following : 1. Replace the system board. 2. If the problem persists, check the AC adapter whether it is correct product or not. Note Noise from the AC adapter does not always indicate a defect.
  • Page 43 Ch4. Symptom-to-part index · The Characteristics of the battery pack 1. Self-discharge The battery gradually loses its power over time without ever being used. 2. Periodic full discharge / charge Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens, you can perform the full discharge / charge to improve the capacity.
  • Page 44 Ch4. Symptom-to-part index · To check the battery pack, do the following : 1. Power off the computer. 2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+). See the following figure : Terminal Voltage (V dc) Ground(-) +0V ~ +12.6V (6 cell / 9-cell)

  • Page 45: Numeric Error Codes

    Ch4. Symptom-to-part index Numeric error codes Symptom / Error FRU or action, in sequence 0200 1.Reset the hard-disk drive. Fixed disk failure 2.Load Setup Defaults in BIOS Setup Utility. (The hard disk is not working) 3.Hard-disk drive. 4.System board. 0210 1.Check the keyboard if it is pressed.
  • Page 46 Ch4. Symptom-to-part index Symptom / Error FRU or action, in sequence 0251 Replace the backup battery and run BIOS Setup Utility System CMOS checksum bad to reset the time and date. - System CMOS checksum is not correct. - Default configuration used. 0252 Reset the password by running BIOS Setup Utility.
  • Page 47 Ch4. Symptom-to-part index Symptom / Error FRU or action, in sequence 02F7 1. DIMM Fail - Safe timer NMI failed 2. System board 0611 1. Load Setup Defaults in BIOS Setup Utility. IDE configuration changed 2. System board. 0612 1. Load Setup Defaults in BIOS Setup Utility. IDE configuration error 2.

  • Page 48: Error Messages

    Ch4. Symptom-to-part index Error message Symptom / Error FRU or action, in sequence Device address conflict. 1. Load Setup Defaults in BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load Setup Defaults in BIOS Setup Utility. 2.

  • Page 49: Lcd-Related Symptoms

    Ch4. Symptom-to-part index LCD-related symptoms Note Before removing or disassembling LCD, power off the computer, unplug all power cords from electrical outlets, remove the battery pack also. Symptom / Error FRU or action, in sequence LCD screen becomes dark suddenly. Check out Battery Miser.

  • Page 50: Indeterminate Problems

    1. Power off the computer 2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnected all of the following devices : a. Non-LG devices. b. Printer, mouse, and other external devices. c. Battery pack. d. PC cards.

  • Page 51: Ch 5. Removing And Replacing A Part (Fru)

    Ch5. Removing and replacing a part Chapter 5. Removing and replacing a part (FRU) Danger Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Caution Before the computer is powered on after FRU replacement, make sure that all screws, springs, and other small parts are in place and are not loose inside the computer.
  • Page 52 Ch5. Removing and replacing a part 1010 Battery Pack 1. Push the battery latch in the direction shown below, then slide the battery pack out of the slot.
  • Page 53 Ch5. Removing and replacing a part 1020 Hard Disk Drive Remove the following parts in order before replacing this part. a. Battery Pack(1010) 1. Remove a screw as indicated in the picture, then pull the HDD assembly out in the direction shown below. FRU No.
  • Page 54 Ch5. Removing and replacing a part 1030 Retainer Remove the following parts in order before replacing this part. a. Battery Pack(1010) 1. Remove 2 screws. FRU No. Specification 1SZZBA4083A M2.0 X L8.0...
  • Page 55 Ch5. Removing and replacing a part 2. To remove three hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard, and pull it up.
  • Page 56 Ch5. Removing and replacing a part 3. Disconnect the keyboard connector.
  • Page 57 Ch5. Removing and replacing a part 1040 Retainer Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) 1. Pull up the retainer, and remove the connector using a (-) type screwdriver.
  • Page 58 Ch5. Removing and replacing a part 1050 Fan Assembly Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) 1. After removing a screw and the connector, pull up and remove the fan assembly using a (-) type screwdriver.
  • Page 59 Ch5. Removing and replacing a part...
  • Page 60 Ch5. Removing and replacing a part 1060-1 Optical Disk Drive (15” Model) Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) 1. Remove a screw, insert a screwdriver into the hole located at the rear of ODD and push it out. FRU No.
  • Page 61 Ch5. Removing and replacing a part 1060-2 Optical Disk Drive (14.1” Model) Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) 1. Remove a screw, insert a screwdriver into the back side of ODD and push it out. FRU No.
  • Page 62 Ch5. Removing and replacing a part 1070 Wireless LAN Card Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) 1. Remove two wireless LAN card connector, open card knob to take out the card.
  • Page 63 Ch5. Removing and replacing a part 1080 MDC Modem Card Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) 1. Remove two screws and insert a screwdriver below the modem. Pull it up to disassemble. FRU No.
  • Page 64 Ch5. Removing and replacing a part 1090 Display Module Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Wireless LAN Card(1070) 1. Remove two screws. FRU No. Specification 1SZZBA4039B M2.5 X L8.0...
  • Page 65 Ch5. Removing and replacing a part 2. Remove two hinge cover screws. FRU No. Specification 1SZZBZ4014A M2.0 X L5.0...
  • Page 66 Ch5. Removing and replacing a part 3. Using a (-) type screwdriver from the back of LCD, pull up the hinge cover with your finger. Then more you move the LCD to the back, the easier the hinge cover will pull out. Remove another hinge cover located on the other side.
  • Page 67 Ch5. Removing and replacing a part 5. Remove the LCD connector located at the upper end of MCD modem. You will see a tag designed to make work easier. Pull out the tag. 4. Remove the LCD cable.
  • Page 68 Ch5. Removing and replacing a part 7. Hold the LCD with your both hands, and pull it up to remove. Note Display Module disassembly in detail (1140)
  • Page 69 Ch5. Removing and replacing a part 1100 Keyboard Deck Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050) e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090) 1.
  • Page 70 Ch5. Removing and replacing a part 14.1” Screw Type Screw Type FRU No. Specification 1SZZBA4083A M2.0 X L8.0 1SZZBA4067A M2.0 X L13.0...
  • Page 71 Ch5. Removing and replacing a part 2. Open the I/O port cover and remove two screws. FRU No. Specification 1SZZBA4017B M2.0 X L3.5...
  • Page 72 Ch5. Removing and replacing a part 3. Remove 3 screws. FRU No. Specification 1SZZBZ4018B M2.0 X L2.0...
  • Page 73 Ch5. Removing and replacing a part 4. Remove the cable, hold the keyboard deck with your both hands and pull it out.
  • Page 74 Ch5. Removing and replacing a part 5. Remove the speaker cable located at the front of key deck that is pulled up.
  • Page 75 Ch5. Removing and replacing a part 1110 Main Board Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050) e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090) h.
  • Page 76 Ch5. Removing and replacing a part 2. Remove the PCMCIA board. 3. Remove the RTC battery connector from Main Board.
  • Page 77 Ch5. Removing and replacing a part 4. Remove the S-Video connector. 5. Remove the LAN S/B connector.
  • Page 78 Ch5. Removing and replacing a part 6. Remove the power cable. 7. Remove 4M/B screws. FRU No. Specification 1SZZBA4014A M2.0 X L5.0 1SZZBA4017B M2.0 X L3.5...
  • Page 79 Ch5. Removing and replacing a part 8. Hold M/B with your both hand and pull it up to remove.
  • Page 80 Ch5. Removing and replacing a part 1120 Battery Frame Assembly Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050) e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090) h.
  • Page 81 Ch5. Removing and replacing a part 2. Pull up the battery frame finger plate, and remove the battery frame assembly. The LAN S/B will be removed as well when the battery frame assembly is disassembled.
  • Page 82 Ch5. Removing and replacing a part 1130 S-Video Sub-Board Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050) e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090) h.
  • Page 83 Ch5. Removing and replacing a part 1140 Display Module Remove the following parts in order before replacing this part. a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050) e. Wireless LAN Card (1070) 1. Using a knife, remove the logo and rubbers that are covering the screws. Then remove all 7 screws. FRU No.
  • Page 84 Ch5. Removing and replacing a part 2. Disassemble the LCD front. The front hook located on the middle of LCD upper and lower end. Be careful of the direction when removing because it is connected from inside out.
  • Page 85 Ch5. Removing and replacing a part 3. Remove cable connector. Remove the cable that is arranged around LCD from LCD frame.
  • Page 86 Ch5. Removing and replacing a part 4. Remove 9 screws (for 15” model) or 8 screws (for 14.1”). (15”) FRU No. Specification 1SZZBZ3009B M2.0 X L2.5 1SZZBA4044B M2.5 XL4.0 1SZZBA4041A M2.0 X L3.0 (15”)
  • Page 87 Ch5. Removing and replacing a part 5. Press the hook on the both side of LCD with a (-) type screwdriver and remove from the LCD real panel.
  • Page 88 Ch5. Removing and replacing a part 6. Remove LCD from the LCD rear panel.

  • Page 89: Ch 6. Part List

    TFT LCD, BOE HYDIS HT14X1B-110 14.1 INCH XGA MKL20 6304FLP079A TFT LCD, LG PHILIPS LP141X13-C2 14.1 INCH XGA MKL20 6304FLP079B LP141X13-C2K1 LG PHILPS TFT COLOR 14.1 INCH XGA(1024X768) ISP STYLE B MKL21 3111BZ7100A CASE ASSY, FRONT 14.1" MKL22 3680BM3036A LENS, WIRELESS REAR 14.1"...
  • Page 90 MKL30 3850BB3035Q EXPORT model For refresh MKL31 3858BZ4450B MCKINLEY N N N MCKINLEY BADGE FOR EXPORT LG model MKB01 6871BF100A1 MAINBOARD ASSY, BH M9+ P.P LGE 8 LAYERS REV 0.5 MKB01 6871BF200A1 MAINBOARD ASSY, BH M10 P.P LGE 8 LAYERS REV 0.5 MCKINLEY US007506 REFRESH MODEL .
  • Page 91 For refresh MKC08 3823B71004F MCKINLEY LG-IBM SUNREX FARSI LM REFRESH 14" model MKC08 3823B70004H MCKINLEY LG-IBM SUNREX K021167 US SOUTH AFRICA 14.1" 84 KEY For refresh MKC08 3823B71004H MCKINLEY LG-IBM SUNREX US SOUTH AFRICA LM REFRESH 14" model MKC08 3823B70004G MCKINLEY LG-IBM SUNREX K021167 UKRAINIAN 14.1"...
  • Page 92 MCKINLEY LG-IBM OKI FARSI LM REFRESH 15" model MKC08 3823B70008H MCKINLEY LG-IBM OKI US SOUTH AFRICA 15" 86KEY For refresh MKC08 3823B71008H MCKINLEY LG-IBM OKI US SOUTH AFRICA LM REFRESH 15" model MKC08 3823B70008G MCKINLEY LG-IBM OKI UKRAINAIN 15" 86 KEY For refresh MKC08 3823B71008G MCKINLEY N OKI UKRAINAIN LM REFRESH 15"...
  • Page 93 MKC10 0IMCRIN106B 1600MHZ/600MHZ B1-STEPPING(SL6FA) PROCESSOR, INTEL RH80535GC0291M 478P UFCPGA PENTIUM-M MKC10 0IMCRIN119A 1700MHZ/600MHZ B1-STEPPING(SL6N5) RH80535NC009512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M MKC10 0IMCRIN150A 1200MHZ/400MHZ B1-STEPPING(SL79S) RH80535NC013512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M MKC10 0IMCRIN132A 1300MHZ/400MHZ B1-STEPPING(SL6N7)
  • Page 94 Ch6. Part lists Location LG P/N SPECIFICATION REMARKS MKC13 6410BK21002 213356-001 VOLEX SAA 1830MM 3PIN CONN. BLACK Australia MKC13 6410BK20705 PL8B1SQJ10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK Australia MKC13 6410BK21007 SP-502B+H05VV-F+IS-034 I-SHENG SAA 1830MM 3PIN CONN. BLACK Australia MKC13 6410BK21006...
  • Page 95 MCKINLEY WIMTEC 2 LAYERS REV 0.3 ODD I/F SUB B/D ASSY MKS06 6871BJ300AA MCKINLEY WIMTEC 2 LAYERS REV 0.3 NETWORK, PWR SUB B/D ASSY MCKINLEY LG-IBM N N WIMTEC 2 LAYERS REV 0.4 NETWORK, PWR SUB B/D For refresh MKS06 6871BJ300AB...
  • Page 96 Ch6. Part lists Location LG P/N SPECIFICATION REMARKS MKM08 3550BM3173B COVER, CLUTCH LEFT MKM09 3550BM3172A COVER, CLUTCH RIGHT MKM10 3550BM3171A DUMMY, PCMCIA MKM11 3550BM4047A DUMMY, SD MKM12 3301BZ9092D PLATE, CHIPSET COVER ASSY 15.0" M9 MKM12 3301BZ9092A PLATE, CHIPSET COVER ASSY 14.1" M9...
  • Page 97 3110BD0008B REAR CASE, 14.1" FOR EXPORT MKL28 3110BD0008D MCKINLEY MG DISPLAY REAR 14.1" FOR MC REFRESH For refresh model MKL29 6871BZT16ZA CABLE FPC, WIRELESS INDICATOR 14.1" MKL31 3858BZ4450B MCKINLEY N N N MCKINLEY BADGE FOR EXPORT LG For refresh model...
  • Page 98 3110BD0009D MCKINLEY MG DISPLAY REAR 15.0" FOR MC REFRESH For refresh model MKL15 3858BZ3019A INSULATOR, INVERTER 14.1"/15.0" MKL17 3550BM2093B DECORATION COVER, 15.0" FOR EXPORT MKL23 3550BM1149B DECORATION COVER, 14.1" FOR EXPORT MKL31 3858BZ4450B MCKINLEY N N N MCKINLEY BADGE FOR EXPORT LG For refresh model...
  • Page 99 MKM22 MKM22 MKL06 MKL16 MKL05 MKL04 MKM23 MKL18 MKM23 MKL13 MKM23 MKL20(14.1") MKL24(14.1") MKL02(15.0") MKM23 MKL09(15.0") MKL11(15.0") MKL25(14.1") MKL26(14.1") MKL10(15.0")
  • Page 100 6304FBH004A TFT LCD, BOE HYDIS HT14X1B-110 14.1 INCH XGA MKL20 6304FLP079A TFT LCD, LG PHILIPS LP141X13-C2 14.1 INCH XGA MKL20 6304FLP079B LP141X13-C2K1 LG PHILPS TFT COLOR 14.1 INCH XGA(1024X768) ISP STYLE B MKL24 4775BZ1004A HINGE ASSY, LEFT 14.1" MKL25 4775BZ1005A HINGE ASSY, RIGHT 14.1"...
  • Page 101 MKL07 MKL07 MKM22 MKL08 MKM21 MKL21(14.1") MKL03(15.0") MKL08 MKM22 MKL30 MKM21 Location LG P/N SPECIFICATION REMARKS MKL03 3111BZ7101A CASE ASSY, FRONT 15.0 MKL07 4850BM4010A CUSHION, RUBBER UPPER MKL08 4850BM4011A CUSHION, RUBBER LOWER MKL21 3111BZ7100A CASE ASSY, FRONT 14.1" MKL30 3850BB3035D MODEL NAME LABEL, MCKINLEY 14.1" FOR EXPORT MKL30 3850BB3035E MODEL NAME LABEL, MCKINLEY 15.0"...
  • Page 102 MKM32 MKM38 Modem MKB01 MKC04 MKC05 MKM19 Mini MKC04 MKM19 Cardbus MKM19 MKS03(15.0") MKS04(14.1") MKS02(14.1") MKS01(15.0") MKM02(14.1") MKM01(15.0") MKC12 MKS06 MKM19 MKM03(14.1") MKM04(15.0")
  • Page 103 6871BJ320AA MCKINLEY WIMTEC 2 LAYERS REV 0.4 SVIDEO, USB SUB 14.1" B/D ASSY MKS06 6871BJ300AA MCKINLEY WIMTEC 2 LAYERS REV 0.3 NETWORK, PWR SUB B/D ASSY MKS06 6871BJ300AB MCKINLEY LG-IBM N N WIMTEC 2 LAYERS REV 0.4 NETWORK, For refresh model PWR SUB B/D ASSY...
  • Page 104 MKM23(14 ) MKM32(15 ) MKM12 MKM38 14 M9 : 3301BZ9092A M10 : 3301BZ9092C MKM29 15 M9 : 3301BZ9092D MKC07 M10 : 3301BZ9092B MKC10 MKS05 MKC02 MKM19 15 ODD I/F MKM17 MKM18 MKH04 MKM16 MKH02 MKM27 MKM27 MKH03...
  • Page 105 0IMCRIN106B PROCESSOR, INTEL RH80535GC0251M 478P UFCPGA PENTIUM-M 1600MHZ/600MHZ B1-STEPPING(SL6FA) MKC10 0IMCRIN119A PROCESSOR, INTEL RH80535GC0291M 478P UFCPGA PENTIUM-M 1700MHZ/600MHZ B1-STEPPING(SL6N5) MKC10 0IMCRIN150A RH80535NC009512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M 1200MHZ/400MHZ B1-STEPPING(SL79S) MKC10 0IMCRIN132A RH80535NC013512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M 1300MHZ/400MHZ B1-STEPPING(SL6N7) MKC10...
  • Page 106 Location LG P/N SPECIFICATION REMARKS MKM12 3301BZ9092D PLATE, CHIPSET COVER ASSY 15.0" M9 MKM12 3301BZ9092A PLATE, CHIPSET COVER ASSY 14.1" M9 MKM12 3301BZ9092B PLATE, CHIPSET COVER ASSY 15.0" M10 MKM12 301BZ9092C PLATE, CHIPSET COVER ASSY 14.1" M10 MKM16 5022BZ4025A THERMAL PAD 19X19 MM ON FAN...
  • Page 107 MKM31 MKM32 MKM33 MKD01 MKM39 MKD03 MKD04...
  • Page 108 Location LG P/N SPECIFICATION REMARKS MKD01 3111BZ8801A KBD DECK ASSY 15.0" MKD01 3111BZ8801B N N KBD DECK ASSY 15" MCKINLEY KBD DECK W/ UV COATED KNOB For refresh model MKD01 3111BZ8800A KBD DECK ASSY 14.1" MKD01 3111BZ8801D MCKINLEY N N MCKINLEY KBD DECK TOTAL ASSY 15.0" FOR MC REFRESH...
  • Page 109 MKC08 MKM32 MKM06(15.0") MKM08 MKM07(14.1") MKM30 MKM32 MKM09 MKM30 MKM10 MKM11...
  • Page 110 3823B70004F MCKINLEY LG-IBM SUNREX K021167 FARSI(IRAN) 14.1" 84 KEY MKC08 3823B71004F MCKINLEY LG-IBM SUNREX FARSI LM REFRESH 14" For refresh model MKC08 3823B70004H MCKINLEY LG-IBM SUNREX K021167 US SOUTH AFRICA 14.1" 84 KEY MKC08 3823B71004H MCKINLEY LG-IBM SUNREX US SOUTH AFRICA LM REFRESH 14" For refresh model MKC08 3823B70004G MCKINLEY LG-IBM SUNREX K021167 UKRAINIAN 14.1"...
  • Page 111 3823B71008F MCKINLEY LG-IBM OKI FARSI LM REFRESH 15" For refresh model MKC08 3823B70008H MCKINLEY LG-IBM OKI US SOUTH AFRICA 15" 86KEY MKC08 3823B71008H MCKINLEY LG-IBM OKI US SOUTH AFRICA LM REFRESH 15" For refresh model MKC08 3823B70008G MCKINLEY LG-IBM OKI UKRAINAIN 15" 86 KEY MKC08 3823B71008G MCKINLEY N OKI UKRAINAIN LM REFRESH 15"...
  • Page 112 MKM30 MKM05 MKC06 MKM33 MKM33 MKM30 MKM28 MKM33 MKC01 MKM33 MKM34 MKM19 MKC11 MKC13...
  • Page 113 Location LG P/N SPECIFICATION REMARKS MKC01 0IMMRSS090A MEMORY, SAMSUNG M470L3224FT0-CB3 SODIMM 256MB DDR 333MHZ MKC01 0IMMRHY044A MEMORY, HYNIX HYMD232M646C6-J SODIMM 256MB DDR 333MHZ MKC01 0IMMRIH032A MEMORY, INFINEON HYS64D32020GDL-6-B SODIMM 256MB DDR 333MHZ MKC01 0IMMRSS091A MEMORY, SAMSUNG M470L6423EN0-CB3 SODIMM 512MB DDR 333MHZ...
  • Page 114 Location LG P/N SPECIFICATION REMARKS MKM05 3581BZ0030A COVER, ASSY DDR MEMORY MKM19 1SZZBA4017B SCREW, D2.0 M2.0 L 3.5 MM TORQUE 2.0 0.2 MKM28 1SZZBA4067A SCREW, D4.0 M2.0 L13.0 MM TORQUE 2.0 0.2 MKM30 1SZZBA4039B SCREW, D4.5 M2.5 L8.0 MM TORQUE 3.0 0.2 MKM33 1SZZBA4083A SCREW, D3.8 M2.0 L8.0 MM TORQUE 2.0 0.2...

This manual is also suitable for:

Lm50

Table of Contents