Using Your Coffeemaker; Setting The Clock; Brew With Grinder On (Using Whole Bean Coffee); Brew With Grinder Off (Using Pre-Ground Coffee) - Wolfgang Puck BCM00015 Use And Care Manual

HSN_7cupGrind&Brew 9/7/07 11:33 AM

Using Your Coffeemaker

Setting the Clock

Press the PROG button once; you will notice the word CLOCK in the
upper right corner of the display screen. Press HOUR or MIN to set the
correct time. Ensure that you are on the correct time of day for AM or
PM. To adjust to AM or PM simply cycle past the 12:00 setting.
Note: If using optional water filter, ensure the filter stem is fully seated
in water reservoir filter holder. Never use warm or hot water to fill the
water reservoir. Use cold water only.

Brew with Grinder On (Using Whole Bean Coffee)

1 Ensure the GRIND OFF function is not enabled (GRIND OFF
INDICATOR light is off).
2 Remove the CHAMBER LID by turning it counter-clockwise and
lifting straight up. You will notice three marks inside the GRINDING
CHAMBER with an indication for 4, 8, or 10 cups. Fill the GRINDING
CHAMBER with roasted coffee beans to the appropriate level for the
number of cups you want to brew.
3 Ensure that the GRINDING CHAMBER CHUTE DOOR is open. To
open the door, slide the lever to the left (see figure 2).
4 Replace the CHAMBER LID by turning clockwise so that the tab fits
within the slot located on the top of the HOUSING (see figure 2).
5 Close the COVER to the HOUSING.
6 Fill the water tank to the amount of cups you want to brew. Do not
exceed the MAX line shown on the WATER WINDOW of the
coffeemaker housing.
7 Place the thermal carafe back into the coffeemaker HOUSING.
8 Press the On/OFF button once. You will begin to hear the grinder
run for approximately 40 seconds and it will be followed by a
buzzing sound. The buzzing sound indicates that the door to the
brewing assembly is closing preventing excess condensation from
entering the grinder.
9 During the brewing cycle the BREW INDICATOR will be illuminated red.
Page 9
9
Using Your Coffeemaker (cont.)

Brew with Grinder Off (Using Pre-Ground Coffee)

1 Press the GRIND OFF button and you will notice the yellow
GRIND OFF INDICATOR light will illuminate
2 Remove the Water Filter Holder by pulling straight out, and add
the appropriate amount of coffee. Replace the Filter Holder back
into the coffeemaker.
3 Fill the water tank to the amount of cups you want to brew. Do not
exceed the MAX line shown on the WATER WINDOW of the
coffeemaker housing.
4 Place the thermal carafe back into the coffeemaker HOUSING.
5 Press the ON/OFF button once. You will hear a buzzing sound for
about 3-4 seconds which indicates that the door to the brewing
assembly is closing preventing excess condensation from entering
the grinder
6 During the brewing cycle the BREW INDICATOR will be illuminated red.
Setting the Delay Timer with Grinder On (Using Whole Bean Coffee)
1 Ensure the GRIND OFF function is not enabled (GRIND OFF
INDICATOR light is off.).
2 Press the PROG button twice and you will notice the word TIMER
displayed in the upper left corner.
3 Press HOUR or MIN to set the correct delay start time. Ensure that
you are on the correct time of day for AM or PM. To adjust to AM or
PM simply cycle past the 12:00 setting.
4 Ensure the GRIND OFF function is not enabled. If the GRIND OFF
indicator light is illuminated in an amber color the coffee maker will
not use the GRINDER and will instead use pre-ground coffee from
the coffee filter.
5 Press the ON/OFF button twice and you will notice that the DELAY
TIMER INDICATOR LIGHT will be illuminated green. The coffeemaker
will begin brewing at the programmed time.
Note: You will hear the grinder start for a second when you press the
ON/OFF button twice. This is normal.
10