Mitsubishi Electric WL7200U User Manual page 28

Viewing video images (continued)
D. Projecting images
Preparation:
• Remove the lens cap.
POWER indicator
STATUS indicator
COMPUTER/DVI-D button
ZOOM/FOCUS button
1. Confirm the POWER indicator lights up red.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating
and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.)
After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Turn on the power of the connected video equipment.
3. Press the POWER button.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
• Do not cover the lens with the lens cap while the lamp is on.
• After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a
product malfunction.
• Regardless of the setting of LAMP MODE, the LOW lamp mode is activated by default whenever the projector
is turned on. When LAMP MODE has been set to STANDARD, the lamp mode changes from LOW to
STANDARD about 2 minutes after turn-on.
• The projector starts warming up when the POWER button is pressed. During the warm-up process, images
may appear dark and no commands are accepted.
• By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when
the STATUS indicator blinks red. (See page 62.)
4. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
5. Adjust with the  or  button to get a fine picture.
• When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is
switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the  or  button
becomes fast, and it becomes slow when STEP is selected.
6. Select an input source.
• Press the VIDEO/HDMI button on the projector or the VIDEO, S-VIDEO or HDMI button on the remote control
that is corresponding to the terminal in use.
• The input source is switched between VIDEO, S-VIDEO and HDMI at every press of the VIDEO/HDMI button on
the projector.
• You cannot change the input source while the menu is being displayed.
• Though it may take some time before an image is displayed on the screen depending on the type of the input
signal, such symptom is not a malfunction.
• Some images become easier to view when the setting of aspect ratio is changed. (See page 24.)
• When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT/VIDEO DVI-D
IN (HDCP) terminal, press the COMPUTER/DVI-D button on the projector to select DVI or press the DVI-D
(HDCP) button on the remote control.
• When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT/VIDEO IN 1 or
COMPUTER/COMPONENT/VIDEO IN 2 terminal, press the COMPUTER/DVI-D button on the projector or the
COMPUTER 1 or COMPUTER 2 button on the remote control.
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specified sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 11.)
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 13.)
9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
10. Adjust with the  or  button to get an approximate size.
• When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is
switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the  or 
button becomes fast, and it becomes slow when STEP is selected.
POWER button
(ON/STANDBY)
, , ,  buttons
ENTER button
LENS SHIFT button
POWER button
(ON/STANDBY)
COMPUTER 1, 2 buttons
VIDEO/HDMI button
LENS SHIFT button
ZOOM/FOCUS button
EN-28
HDMI button
VIDEO button
S-VIDEO button
DVI-D(HDCP) button
ENTER button
, , , 
buttons