Ip Address Settings - Mitsubishi Electric WL7200U User Manual

Initial network settings (continued)
CLEAR key: ..... Deleting all the entered
characters.
• You can enter numbers by pressing the number
buttons (0 to 9) while holding down the NUM
button on the remote control.
• The default password is "admin".
5. Select OK, and NEW NETWORK PASSWORD
screen appears if the entered password is correct.
• If the entered password is not correct,
CURRENT NETWORK PASSWORD screen
appears again.
NEW NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
CONFIRM NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
A B C D E
N O P Q R
0 1 2 3 4
OK
6. Enter the NEW NETWORK PASSWORD and
CONFIRM NETWORK PASSWORD.
• Password can be set using up to 32 characters
including alphabets (capital/small) or numeric
characters.
← key: ............. Shifting the position of enter
cursor to the left for each
character.
→ key: ............. Shifting the position of enter
cursor to the right for each
character.
key: ............... Shifting the position of
enter cursor between NEW
NETWORK PASSWORD
and CONFIRM NETWORK
PASSWORD.
DEL key: .......... Deleting the character in the
position of enter cursor for each
character.
caps/CAPS key: Switching an alphabet character
to CAPITAL or small.
CLEAR key: ..... Deleting all the entered
characters.
• You can enter numbers by pressing the number
buttons (0 to 9) while holding down the NUM
button on the remote control.
7. When NEW NETWORK PASSWORD and CONFIRM
NETWORK PASSWORD are matched, the setting
is completed after changing the NETWORK
PASSWORD.
• When you select OK and the passwords you
entered are matched, the setting change dialog
is displayed. After the dialog disappears, the
NETWORK menu is displayed.
• When you select CANCEL, the NETWORK menu
is displayed without changing the password.
• If the entered content is not matched, NEW
NETWORK PASSWORD screen appears again
after an error dialog is displayed.
• The password for the web control software
of CRESTRON cannot be changed with this
setting.
• It may take some time to reflect the settings.
← →
F G H I J K L M DEL
S T U V W X Y Z caps
5 6 7 8 9 CLEAR
CANCEL
IP Settings
(See page 31 for menu setting.)
1. Display the NETWORK menu.
2. Press the  or  button to select IP CONFIG.
IP CONFIG
3. Press the ENTER button.
• IP CONFIG menu appears.
NETWORK
IP CONFIG
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
MAC ADDRESS
SAVE SETTINGS
Setting or Clearing DHCP
1. Display the IP CONFIG menu.
2. Press the  or  button to select DHCP.
DHCP
3. Press the  or  button to select ON or OFF.
• When setting DHCP to ON, IP ADDRESS,
SUBNET MASK, and DEFAULT GATEWAY
cannot be set. If you set those settings, set
DHCP to OFF and perform the IP settings as the
following procedures.
• Until the execution of SAVE SETTINGS, the
change is not saved.

IP Address Settings

1. Display the IP CONFIG menu.
2. Press the  or  button to select IP ADDRESS.
IP ADDRESS
3. Press the ENTER button.
• IP ADDRESS screen appears.
4. Press the direction buttons to move the key cursor,
select the numbers to enter, and press the ENTER
button.
• Set the numeric value within the range from 0 to
255. However, set the numeric value for the final
octet within the range from 1 to 254.
← key:
→ key:
DEL key: Deleting the character in the position
CLEAR key:
EN-45
ENTER
opt.
ON
0. 0. 0. 0
0. 0. 0. 0
0. 0. 0. 0
OK
ON
0. 0. 0. 0
IP ADDRESS
192 . 168 . 0 . 10
← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Shifting the position of enter cursor to
the left.
Shifting the position of enter cursor to
the right.
of enter cursor for each character.
Deleting all the entered
characters.