Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Avid Technology ML530
Summary of Contents for Avid Technology ML530
- Page 1 ML530 Guide System 5...
- Page 2 Legal Notices This guide is copyrighted ©2011 by Avid Technology, Inc., (hereafter “Avid”), with all rights reserved. Under copyright laws, this guide may not be duplicated in whole or in part without the written consent of Avid. 003, 96 I/O, 96i I/O, 192 Digital I/O, 192 I/O, 888|24 I/O, 882|20 I/O,...
-
Page 3: Table Of Contents
Contents Chapter 1. Introduction to the ML530 ............. . 1 Features. - Page 4 ML530 Guide...
-
Page 5: Chapter 1. Introduction To The Ml530
24 channels of variable gain inputs are desired. Features The ML530 provides gain over a range of -12 to +72 dB in 0.5 System Requirements and dB increments for each channel. The ML530 also features a Compatibility high-pass filter, HiZ/LowZ switch, and phantom power. -
Page 6: About This Guide
About This Guide About www.avid.com This guide provides a basic overview of ML530 features and The Avid website (www.avid.com) is your best online source functionality. for information to help you get the most out of your system. The following are just a few of the services and features For complete instructions on connecting and configuring available. -
Page 7: Chapter 2. Ml530 Features
• Phase: Phase invert (green) • Pad: 12 dB attenuation (green) Clip Mute LowZ Phase Front panel Channel Status LEDs Since the ML530 is software controlled, the power switch is the only front panel control. Chapter 2: ML530 Features 3... -
Page 8: Back Panel
ML530 1 -12 13-24 CONTROL ML530 front panel Inputs (38-pin Elco) 24 inputs are provided on two 38-pin Elco connectors. The level of all signals input at these ports can be boosted or attenuated. In standard configuration, the input cable is configured by the customer. Elco connectors and pins are provided. -
Page 9: Chapter 3. Configuration And Connection
Control Room AM713 Use relative locations to determine cable lengths ML530 ML530 standard cable diagram Elco crimp pins and hoods for inputs are supplied in accessory cable kits. Input cabling is not included. Cable Specifications Cable Description 10M Part #... -
Page 10: Connection Diagram
Elco 38 from Sync DA Mic/Line Analog Out Control from PC253i Elco crimp pins and hoods for user Interface Pilot 5, 6 inputs are supplied in accessory cable kits. Input cabling supplied by customer ML530 standard configuration ML530 Guide... -
Page 11: Optional Input Patch
Input Patch cable diagram The optional input patchbay has the capacity to provide input patching to 48 channels or two ML530 interfaces. An additional set of cable D (below) is required for the second ML530 interface. Patchbay, cables, and pins are ordered separately. -
Page 12: Connection Diagram
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Input patch configuration ML530 Guide... -
Page 13: Elco 38 Input/Output Pinout
Mic In 11 / Mic In 23 From studio Mic 11 / 23 Mic In 12 / Mic In 24 From studio Mic 12 / 24 ML530 In 1/In 2 pinout: Elco 38 socket Signal Wiring Instruction & Description Mic Pre Out 1 / Out 13... - Page 14 ML530 Guide...
-
Page 15: Appendix A. Ml530 Specifications
Equivalent Input Noise (EIN) Common Mode Rejection (CMR) >50 dB (10 Hz – 20 kHz) Phase Linearity ±10° (25 Hz – 20 kHz) High-pass Filter 80 Hz 18 dB/octave switched per channel Phase Invert 180° switched per channel Appendix A: ML530 Specifications 11... -
Page 16: Environmental And Power Specifications
Environmental and Power Specifications Operating Temperature 5–35°C Power Requirements 90–250 VAC, 50/60Hz Power Consumption 100 W Physical Dimensions Height 3.5 inches Width 19 inches Depth 18.6 inches Weight 17 lb ML530 Guide... -
Page 17: Appendix B. Compliance Information
Appendix B: Compliance Information Proposition 65 Warning Environmental Compliance This product contains chemicals, including lead, Disposal of Waste Equipment by Users in the known to the State of California to cause cancer European Union and birth defects or other reproductive harm. Wash hands after handling. -
Page 18: Emc (Electromagnetic Compliance)
Avid is authorized to apply the CE (Conformité Europénne) mark on this compliant equipment thereby declaring conformity to EMC Directive 2004/108/EC and Low Any modifications to the unit, unless expressly approved by Voltage Directive 2006/95/EC. Avid, could void the user's authority to operate the equipment. ML530 Guide... -
Page 19: Safety Compliance
13) Unplug this equipment during lightning storms or when unused for long Safety Compliance periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the equipment has been damaged in any way, such as power-supply cord or plug Safety Statement is damaged, liquid has been spilled or objects have fallen into the equipment, the equipment has been exposed to rain or moisture, does not operate normally,... - Page 20 ML530 Guide...
- Page 22 Avid Technical Support (USA) Product Information 2001 Junipero Serra Boulevard Visit the Online Support Center at For company and product information, Daly City, CA 94014-3886 USA www.avid.com/support visit us on the web at www.avid.com...
Need help?
Do you have a question about the ML530 and is the answer not in the manual?
Questions and answers