Sharp AQUOS LC-42D65U Operation Manual page 41

Appendix
PC control of the TV
• Attach an R3-232C cable cross-type (commercially
available) to the supplied Din/D-Sub RS-232C for the
connections.
oThis operation system should be used by a person who is
accustomed to using computers.
m Communication conditions
Set the RS-232C communication settings on the PC to
match the TV's communication conditions.
The TV's communication settings are as follows:
9,600 bps
8 bits
None
1 bit
None
m Communication procedure
Send the control commands from the PC via the RS-
232C connector.
The TV operates according to the received command
and sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
m Command table
• Commands not indicated here are not guaranteed to operate.
m Command format
EightASCII codes ÷ OR
\ .......................................................... Y................................................ / \ ........................................................... ]............................................... / \ _-/
Command 4-digits Parameter 4-digits Return code
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0-9, x, blank, ?
m Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that 4 values are
input for the parameter.)
When the input parameter is not within an adjustable
range, "ERR" returns. (Refer to "Response code format".)
Any numerical value can replace the "x" on the table.
When "?" is input for some
commands, the
present setting
value responds.
m Response code format
Normal response Problem response (communication
error or incorrect command)
IEIRIR) I
Return code (0DH) Return code (0DH)
CONTROL ITEM COMMAND PARAMETER
POWER ON COMMAND SETRNG R)S)P)W O) ) ) Off
i i i 11 i i On
POWER SETIING PiOiWi R 0i i i P....... off
i i i _i i i P ....... On
INPUTSELECTIONATOGGLE I ITIGID xl i i (Toggle)
TV I iTiViD oi i i
INPUT1 9 I iA i V i D * i i i Input terminalnumbe/(1 9)
(NPUT SELECTION B (NPUT 1 IiNiPil *i i i o: Auto, 1: VDEO, 2: COMPONENT
(NPUT2 liNiPi2 *i i i 0:Auto, 2:C©(V_PONENT, 3: S TERMINAL
AV MODE SELECTION A iV i M i D * i i i 0: (Toggle), 1: STANDARD, 2: MOVIE, 3: GAME, 4: USER,
VOLUME
POSITION H-POSmON
V POSmON
CLOCK
PHASE
VIEW MODE
i i i i i i 5: DYNAMIC (Fixed}, 6: DYNAMIC, 7: PD
V )0 ) L )M * )* ) ) Volume ¢,_00/
HIPIOIS *i*i*i
I I I I I I
VIPIOIS *i*i*i
oiLiCiK *i*i*i Only PC mode. (O lSO)
P)H)S)E " )* ) " ) OrU PC mode./O 40/
wiliDiE *i i i 0:(Toggle)[AV],l:SideBa/[AV],2:S.Stretch[AV]
i i i i i i 3: Zoom [AV}, 4: Stretch [AV], 5: No/real [PC)
i i i i i i 6: Zoom [PC], 7: Stretch [PC],
8: Dot by Dot [PC] [AV], 9: EuUScreen [AV]
MIUITIE * i i i O: (Toggle), l: On, 2:Off
AiOiSiU, , , _i i i O:/Togg_e/.f:On. 2:Off
A i C i H i A x i i i (Toggle)
oiEiTiM *i i i 0:Off, I:OFFTIMER 30MIN,2:OFFTIMER 60MIN,
', ', ', ', ', ', 3: OFF TIMER 90 MIN, 4: OFF TIMER 120 MIN
D)o)o)H")*)')Thoc,anneInumberof_
i i i i i i (_fss)
l l l l l l
DjAj2 jP * j* j *j * (01009999)
DiOi2iU i i i * ii * ii * ii (1999)
DIOI2IL i i i *)*)*)(0999)
aicil ;:1 *i*i*i*
(06383)
ciHiuiP ×i i i Th_0h_,_r_elnun-,be_ofW+l
O)H)D)W×i)) Th_0h_,_r_olnumbe,_ofW 1
ciLiciP xi i i (Toggle)
MUTE
SURROUND
AUDIO SELECTION
SLEEP TIMER
CHANNEL DIRECT
CHANNEL
_NALOG)
DIRECT
CHANNEL
(DIGITAL)
CH UP
CH DOWN
CC
CONTROL CONTENTS
The Power On command re)ected.
The Power On command accepted.
It shifts to standby.
Power On
It input switches by the toggle. (It is the same as an input change key}
It input switches to TV. (A channel/÷mains as it is. (L_st memory})
It input switches to INPUT1 -INPUTg.
An input change is also included.
Although it can choose now, it is toggle operation in inside.
The screen posRion variable ranges depend on the View Mode or the
signal type. The ranges can be seen on the position setting screen.
0: Although it carl choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Avaibble except when UXGA is being input.
[AV] Only available when 1O8OVp is being input.
9: Only available when 720p is being input.
An input change is included if it is not TV display.
In Air, 2-690h is effective.
In Cable, 1 135ch is effective.
DIGITAL Air (Two Part numbers, 2 digit plus 2 digit)
DIGITAL Cable (Two Part numbers, 3 dig_t plus 3 digit)
E/_}nt half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
DIGITAL Cable (Two Part numbers, 3 digit plus 3 digit)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
DIGITAL Cable (One Part numbers, 5 digit, bss than 10,000)
DIGITAL Cable (One Part numbers, 5 digit, more than 10,000)
If it is not TV display, it will input switch to TV. (same function as CHA)
If it is not TV display, it will input switch to TV. (same function as CHV)
Toggle operation d a closed caption.
= If an underbar (_)appears in the parameter column, enter a space.
= If an asterisk (*)appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
= Any numerical value can replace the "x" on the table.
@- 40