Advertisement
_kTOI'E:
t !you went
1 _l through First Time Setup
(page 3), this task has already
been completed for you.
You need to make sure that
the TV is set to pick up either
Cable TV stations or Antenna
signals. In other words, the
TV needs to know whether
you have connected a Cable
TV signal or a normal anten-
na to its ANTENNA plug (see
page 2).
Press the MENU (M)--
button on the remote, then the
CHANNEL • or • buttons
(or press the MENU • or •
on the TV) to select the word
CABLE with the TV's on-
screen Arrow.
_Press
the VOLUME (+)
or (-) buttons (on the TV or the
remote) to select either:
YES-
If you DO have Cable
TV connected to the
TV. Channels 1-125
can be selected.
NO-
If you have an Antenna
connected to the TV.
Channels 2-69 can be
selected.
' 3<_P--_-_essSTATUS button on
]
the remote control to clear the I
screen.
[
L
IlfllllPIIIIIII IJlfllIll
II
Try it out.
!
Press the CHAN-
NEL • • buttons
and scan the chan-
nels. CHA•
works
only after STATUS
button is pressed to
clear the screen (or
Menu times out -
about 1 minute.)
Remember,
to set
the "IV to select the
channels on your
Cable system, or in
your area, see the
"Autoprogram" and
"Adding Channels "
in the section
below.
I[ you went
through First Time Setup
(page 3), this task has already
been completed
for you.
Auto-Program
is for adding
local area channel
numbers
into the memory
of the TV
This makes it easy for you to
select only your area (or
Cable system)
channels
when
the CHANNEL
• •buttons
are pressed.
Press the MENU (M)
button on the remote, then the
CHANNEL • or • buttons
(or the MENU • or • buttons
on the TV) to select the word
PROGRAM with the TV's on-
screen Arrow.
_Press
the VOLUME (+)
I <
button (on the TV or the
remote) to PROGRAM.
Illl
_Press
the VOLUME (+)
button again to start the TV
search for area channels.
Flashing channel numbers will
count upward on the screen as
the TV looks for channels to
"ADD".
/"
You may press any button
(on the TV or remote) to stop
he channel search at any time.
When the channel search is
completed the TV will retum to
the last viewed channel.
The TV screen will be blocked
off until the search for channels
is done.
"RED"
channel numbers
have been
added to the TV's memory.
"WHITE"
channel numbers
are not
present in the TV's program memory.
[--t_[_Try
it out. Press ! To drop any unwanted channels
When searching for channels the
] _(-_/
CHANNEL
••
buttons I from the, TV's memory, see
TV screen display may jitter
[..k 7/.a OLsee which
channels I howto
Manually
delete
slightly. This is normai and does
have been added
t ch
I
|
nave oeen a
.
annels in the section below,
not indicate a need for service.
____l_p--_es
s
uto-Program
(see above)
adds all the channels
it
can find
(on your Antenna
or
Cable TV system)
into the
TV's memory.
Save/Delete
channels
makes it easy for
you to add other channels,
or
drop unwanted
channels,
from the list of channels
in
the TV's memory.
the MENU (M)
button on the remote, then
the CHANNEL
• or • but-
tons (or the MENU • or •
on the TV) to select the word
CHANNEL with the TV's on-
screen Arrow.
_Prress
Channel Number
buttons on the remote (or
CHANNEL •V
buttons on the
TV) to select the channel you
want to SAVE (or DELETE.)
12
_Press
the VOLUME (+) --I ,/4_
Press the STATUS button
button to SAVE the selected/
to clear the screen after adding
channel number into memory.
(or deleting) all the channels
Press (-) button to DELETE a
you want.
channel from memory.
11
Illllllllllllllrlllllllr
------ lllllllllllllll
Ill
The channels you SAVED
should appear. The channels
you DELETED should not
appear.
To SAVE a channel above 100,
use the CHA•
buttons on the
TV. The remote number buttons
only go up to channel 99.
Advertisement
