Table of Contents
Advertisement
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DMP2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front & Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DMP2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting The Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Low-Cut Rumble Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Phase Inversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Phantom Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Balanced vs. Unbalanced Outputs . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for M-Audio DMP2
Summary of Contents for M-Audio DMP2
-
Page 1: Table Of Contents
DMP2 Operation ........ -
Page 2: Introduction
Each channel provides low impedance microphone inputs on XLR connectors with optional phantom power, plus an alternate high impedance instrument input on 1/4" TS jacks. The DMP2 outputs can be used as balanced or unbalanced via a TRS jack. -
Page 3: Front & Rear Panels
7. Main Power LED: When the proper power supply is applied to the DMP2 and the Main Power switch is switched to the ‘On’ position, this LED will light, indicating that the unit is powered up. -
Page 4: Dmp2 Operation
3. With all volume controls at their lowest settings, turn on your DMP2, then your sound system. Setting the Gain The DMP2 provides up to 70dB of gain on the XLR inputs, and up to 50dB of gain on the high impedance inputs. Microphones and guitar pickups... -
Page 5: Low-Cut Rumble Filter
When the signal present or "sig" LED lights fairly consistently, you’ve reached a good signal level for the DMP2. Some users may wish to experiment a little further to find what audibly might be referred to as a "sweet spot."... -
Page 6: Balanced Vs. Unbalanced Outputs
"Phantom Power" must be applied from the pre- amp. Pressing the "phan" button and engaging phantom power on the DMP2 will send the necessary voltage to both of the XLR Mic Inputs. Phantom power will not affect a dynamic mic adversely, so its okay to have a dynamic mic at the XLR input while phantom power is switched on. -
Page 7: Specifications
Specifications General Maximum Input - Mic In: -25 dBv Maximum Input - Instr. In: -5 dBv Maximum Output - Balanced: 24 dBv Maximum Output - Unbalanced: 10 dBv Headroom: 20 dB Maximum Gain - Mic In: 70 dB Maximum Gain - Instr. In: 50 dB Clip Indicator: 2 dB below threshold of clipping... -
Page 8: Limited Lifetime Warranty
Limited Lifetime Warranty MIDIMAN warrants that this product is free of defects in materials and workmanship under normal use so long as the product is: owned by the original purchaser; the original purchaser has proof of purchase from an authorized MIDIMAN dealer;...
Need help?
Do you have a question about the DMP2 and is the answer not in the manual?
Questions and answers