Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Automatic DB 5801
Summary of Contents for Automatic DB 5801
- Page 1 INSTRUCTION MANUAL DB 5801 250W MULTI TOOL...
-
Page 2: Table Of Contents
CONTENTS Warranty Introduction Environmental protection Description of symbols Specifications General safety rules Additional safety rules for oscillating tools Accessories Unpacking Know your product Installing accessories Installing sandpaper On/off switch Flush cutting a door jamb and casing for installing flooring Cutting a hole in wood flooring to install a heating vent Using the detail sander attachment Using the scraper blade... -
Page 3: Warranty
Warranty Power Tools desk will be borne by you! We will then, at our option, either repair or replace the product, or refund your 1 Year Repair Warranty. money and take back the product - in accordance with our Returns Policy, a copy of which is available at www. -
Page 4: Introduction
Introduction Description of symbols Your new AUTOMATIC power tool will more than satisfy The rating plate on your tool may show symbols. These your expectations. It has been manufactured under represent important information about the product or stringent AUTOMATIC Quality Standards to meet superior instructions on its use. -
Page 5: General Safety Rules
General safety rules increase the risk of electric shock. d) Do not abuse the cord. Never use the cord WARNING: Read all safety warnings and all instructions. for carrying, pulling or unplugging the Failure to follow the warnings and instructions may result in power tool. - Page 6 energising power tools that have the switch on invites measures reduce the risk of starting the power tool accidents. accidentally. d) Remove any adjusting key or wrench d) Store idle power tools out of the reach before turning the power tool on. A wrench or of children and do not allow persons a key left attached to a rotating part of the power tool unfamiliar with the power tool or these...
-
Page 7: Additional Safety Rules For Oscillating Tools
plug from the power source before installing or removing an 5) Service accessory. a) Have your power tool serviced by a Never use dull blades in the tool. They will cut slower, qualified repair person using only identical replacement parts. This will ensure that the safety leave rough cuts and break easily due to added pressure of the power tool is maintained. -
Page 8: Accessories
Due to modern mass production techniques, it is unlikely 1 x 6 mm Hex key/ Allen Key that your AUTOMATIC Power Tool is faulty or that a part is 1 x Screw missing. If you find anything wrong, do not operate the tool... -
Page 9: Installing Accessories
Installing blade accesssories Notes: a) Check to make sure the convex curve of the washer is facing the head of the screw. b) Make sure the alignment holes in the blade are still mated with the alignment pins in the accessory holder. All accessories are installed on the oscillating tool in a simi- lar manner. -
Page 10: Installing Sandpaper
Installing sanding pad and sandpaper OFF switch toward the front of the tool. 2. To turn the tool OFF, press the rear part of 1. Install the hook & the ON/OFF switch and allow the switch to loop sanding pad slide to off position. -
Page 11: Cutting A Hole In Wood Flooring To Install A Heating Vent
Note: The tool and blade should be at a 45° angle to the floor tile. floor to allow the corner of the blade to plunge cut into the Note: Hold the tool tightly and do not put too much flooring. forward pressure on the saw blade when cutting, as this will 5. -
Page 12: Using The Scraper Blade
Using the scraper blade accessories. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. It will also void the warranty. 1. Install the scraper blade on the multi-tool. Lubrication When using the scraper blade to scrape old finishes or glue from a workpiece, place the underside of the blade All of the bearings in this tool are lubricated with a sufficient flat on the workpiece surface and then lift upward on the... - Page 13 DISTRIBUTED BY; Global Power Brands International Pty. Ltd. PO Box 413 Mooroolbark VIC 3138 ABN. 39 131 999 914 Ph. 1800 909 909 help@globalpowerbrands.com...
Need help?
Do you have a question about the DB 5801 and is the answer not in the manual?
Questions and answers