Husqvarna 2754GLS Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. 2754GLS
  6. Owner's manual

Husqvarna 2754GLS Owner's Manual

96043006600
Hide thumbs Also See for 2754GLS:
Table of Contents

Advertisement

Quick Links

03002
2754GLS
Owner's Manual / 96043006600 / 2008-12

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 2754GLS

Summary of Contents for Husqvarna 2754GLS

  • Page 1 03002 2754GLS Owner's Manual / 96043006600 / 2008-12...

  • Page 2: Safety Rules

    SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Do not operate machine without the entire grass catcher, WARNING: In order to prevent ac- discharge guard, or other safety devices in place and ci den tal starting when setting up,...
  • Page 3 SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE Tragic accidents can occur if the operator is not alert to • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment the presence of children.

  • Page 4: Table Of Contents

    PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. Gasoline Capacity 4 Gallons and type: Unleaded Regular • Follow a regular schedule in maintaining, caring for and using your tractor. Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) •...

  • Page 5: Unassembled Parts

    UNASSEMBLED PARTS Mower Mower Front Wheel (5) Large Retainer (1) 3/4 O.D. Washers Springs - 7/16 (1) Wheel (1) 1-1/4 O.D. Washer (2) Smaller Retainer (1) Locknut Springs - 5/16 (1) Shoulder Bolt 3/8-16 (5) 1-3/16 O.D. Washers Slope Sheet (1) Oil Drain Tube For Future Use Keys...

  • Page 6: Assembly

    ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur- poses. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. (1) 3/4" wrench (1) Utility knife (1) 9/16"...
  • Page 7 ASSEMBLY ASSEMBLE FRONT WHEEL TO MOWER (See Fig. 3) • Using shoulder bolt, washer and locknut from parts bag, as sem ble front wheel to mower as shown. Tighten securely. FIG. 5 NOTE: Be sure mower side suspension arms (A) are point- FIG.
  • Page 8 ASSEMBLY • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO • Turn steering wheel to position wheels straight for- CHASSIS - Position hole in arm over pin (B) on outside ward. of tractor chassis and secure with washer and retainer • ATTACH FRONT LINK (E) - Work from left side of spring.
  • Page 9 ASSEMBLY ✓CHECKLIST BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been com plet ed. ✓ No remaining loose parts in carton. ✓...

  • Page 10: Operation

    OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST SLOW REVERSE HIGH NEUTRAL CHOKE IGNITION SWITCH ENGINE START MOWER HEIGHT MOWER LIFT REVERSE ENGINE ON PARKING BRAKE ENGINE OFF OPERATION SYSTEM (ROS)
  • Page 11 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. FIG.
  • Page 12 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 13 OPERATION • The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6 inches in height should be mowed twice.

  • Page 14: Before Starting The Engine

    OPERATION • Slowly depress appropriate drive pedal to slowest set- ting. • Make all turns slowly. TO TRANSPORT (See Figs. 13 and 21) When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in free wheel ing po si tion.
  • Page 15 OPERATION TO START ENGINE (See Fig. 13) • For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the When starting the engine for the first time or if the engine Maintenance sec tion of this manual). has run out of fuel, it will take extra cranking time to move •...

  • Page 16: Operation

    OPERATION PURGE TRANSMISSION MOWING TIPS • Mower should be properly leveled for best mowing CAUTION: Never engage or disengage performance. See “TO LEVEL MOWER HOUSING” in freewheel lever while the engine is the Service and Adjustments section of this manual. run ning.

  • Page 17: Maintenance Schedule

    MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH SEASON STORAGE SCHEDULE HOURS HOURS HOURS HOURS Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Check Mower Levelness...

  • Page 18: Maintenance

    MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be sharp. Re place Always observe safety rules when per form ing any main- worn, bent or damaged blades. te nance. BRAKE OPERATION CAUTION: Use only a replacement blade approved by the manufacturer of your If tractor requires more than five (5) feet to stop at highest tractor.

  • Page 19: Clean Air Screen

    MAINTENANCE TO CHANGE ENGINE OIL (See Figs. 25 and 26) • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush Determine temperature range expected before oil change. until bright. All oil must meet API service classification SG-SL. •...

  • Page 20: Spark Plugs

    MAINTENANCE DECK WASHOUT PORT (See Fig. 27) ENGINE OIL FILTER Your tractor’s deck is equipped with a washout port on Replace the engine oil filter every season or every other its surface as part of its deck wash system. It should be oil change if the tractor is used more than 100 hours in utilized after each use.

  • Page 21: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST- MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. •...
  • Page 22 SERVICE AND ADJUSTMENTS • Go to side of mower you wish to adjust. FRONT-TO-BACK ADJUSTMENT (See Figs. 32 and 33) • With a 3/4" or adjustable wrench, turn lift link adjust- IMPORTANT: Deck must be level side-to-side. ment nut (A) to the left to lower the mower, or, to the To obtain the best cutting re sults, the mower blades should right to raise the mower.

  • Page 23: To Check Brake

    SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest MOWER DRIVE BELT REMOVAL (See Fig. 34) speed in high est gear on a level, dry concrete or paved •...
  • Page 24 SERVICE AND ADJUSTMENTS WASH ERS RE TAIN ING RING AXLE COVER SQUARE KEY (REAR WHEEL ONLY) FIG. 36 TO START ENGINE WITH A WEAK BATTERY (See Fig. 37) WARNING: Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies.

  • Page 25: Interlocks And Relays

    SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 38) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 39) WARNING: Do not short battery ter mi nals by allowing a wrench or any other object to contact both terminals at • Raise hood. the same time.

  • Page 26: Storage

    STORAGE Immediately prepare your tractor for storage at the end ENGINE of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS WARNING: Never store the trac tor with FROM FORMING IN ES SEN TIAL FUEL SYSTEM PARTS SUCH gas o line in the tank inside a building AS CARBURETOR, FUEL FIL TER, FUEL HOSE, OR TANK...

  • Page 27: Trou Ble Shoot Ing

    TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4.

  • Page 28: Trou Ble Shoot Ing

    TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine dies when 1. Reverse operation system 1. Turn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged. Engine continues to 1.

  • Page 29: Repair Parts

    TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 SCHEMATIC SCH12 BATTERY SOLENOID STARTER FUSE AMMETER BLACK (OPTIONAL) ELECTRIC CLUTCH WHITE PTO SWITCH BLACK WHITE (DISENGAGED) WHITE BLACK GRAY CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) BLACK...
  • Page 30 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 ELECTRICAL T14S With 12V Outlet Option...
  • Page 31 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 ELECTRICAL PART DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 532 18 64-91 Box Battery 532 17 61-38 Switch Interlock Push-In 532 18 37-59...
  • Page 32 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 CHASSIS chassis-tex_TEX GT HUSQ_50...
  • Page 33 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 CHASSIS PART PART DESCRIPTION DESCRIPTION 532 40 50-12 Logo 873 90 05-00 Nut Lock Hex Flange 5/16-18 532 42 54-42 Dash 532 41 77-78 Console Asm. Deck Lift 532 41 10-46...
  • Page 34 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 DRIVE drive-tex_G700_pedal_2...
  • Page 35 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 DRIVE PART PART DESCRIPTION DESCRIPTION - - - - - - Transaxle, Hydro G7-BCBB- 876 02 04-12 Pin Cotter 1/8 x 3/4 1XDC-1FCA 532 16 94-84 Retainer Clip 532 00 70-70 Key 1/4 x 2.5...
  • Page 36 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 ENGINE engine-tex_bs-2cyl_25...
  • Page 37 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 ENGINE PART PART DESCRIPTION DESCRIPTION - - - - - - Engine B&S Model No. 44Q777- 532 15 99-55 Tube Exhaust LH 1039-B1 532 16 05-89 Tube Exhaust RH...
  • Page 38 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 STEERING ASSEMBLY PREM 2 HUSQ SR steering-tex_special_13_r1...

  • Page 39: Steering Assembly

    TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 STEERING ASSEMBLY PART DESCRIPTION 532 41 64-80 Wheel, Steering 532 19 36-51 Wheel, Steering Prem 2 532 19 59-68 Axle Asm., Front 532 40 30-89 Spindle Asm. LH 532 40 30-90 Spindle Asm.

  • Page 40: Seat Assembly

    TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 SEAT ASSEMBLY seat-tex_6.5SL_2 PART PART DESCRIPTION DESCRIPTION 532 40 66-21 Seat 873 80 05-00 Nut, Lock 5/16-18 unc 532 19 76-61 Handle Slide Seat 532 18 01-66 Bracket Pivot Fender...

  • Page 41: Wheels And Tires

    TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 DECALS PART PART DESCRIPTION DESCRIPTION 532 17 05-63 Decal, Mower Warning Keep Hand 532 41 16-58 Decal, Operator's 532 42 47-89 Decal, Hood Emblem Away 532 41 82-16 Decal, Panel SD...

  • Page 42: Mower Deck

    TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 MOWER DECK 16 19 mower_deck 54-tex_10_r1...
  • Page 43 TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 MOWER DECK PART PART DESCRIPTION DESCRIPTION 532 41 87-08 Deck Weldment Mower 532 18 73-42 Baffle Right 532 19 60-66 Cover Mandrel LH 532 18 73-44 Baffle Left 532 19 71-81...

  • Page 44: Mower Lift

    TRACTOR - MODEL NO. 2754GLS (96043006600), PRODUCT NO. 960 43 00-66 MOWER LIFT lift-tex_3 PART PART DESCRIPTION DESCRIPTION 532 19 52-23 Shaft Asm., Lift 532 19 42-08 Pin Cotter 5/16 Bow Tie Lock 532 19 52-30 Lever Asm., Lift RH...
  • Page 45 SERVICE NOTES...
  • Page 46 SERVICE NOTES...
  • Page 47 SECTION 1: LIMITED WARRANTY Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that the Product shall be free from defects in material and workmanship from the date of purchase for the period of the applicable “Warranty Schedule” of the Product as set forth below. Additional limitations are described in Section 2 through 6, inclusive.
  • Page 48 Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address of the selling retailer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure.
  • Page 49 532 42 56-14 12.02.08 TH Printed in U.S.A.

Table of Contents