MTD 608 Operator's Manual page 35

REE PART
NO. NO.
2 710-0604A
3 783-0726A
4 783-0727
5 783-0728
6 710-0723
7 711-1408
8 711-1655
9 712-0240
10 712-0241
11 712-0431
12 712-0459
13 712-3004A
14 717-1550D
15 717-1554
16 723-0448A
17 736-0169
18 736-3084
19 738-1001A
20 741-0475
21 741-0656
22 738-0372B
23 631-0027
24 731-0220
25 638-0019
638-0021
26 638-0020
638-0022
27 683-0128A
28 712-0431
29 714-0470
30 726-0214
Models607, 608 & 609
DESCRIPTION
Self-tapping Screw, 16-18 x .625
RH Pivot Support Bracket
LH Pivot Support Bracket
Pivot Bar Bracket
Hex Cap Screw, 3/8-16 x 1.25 (Grade 5)
RH Drag Link
LH Drag Link
Jam Nut, 7/16-20 (Grade 2)
Hex Nut, 3/8-24 (Grade 2)
Flange Lock Nut, 3/8-16
Flange Lock Nut, 7/16-20
Flange Lock Nut, 5/16-18
Steering Gear, 11/90 Ratio
Steering Pinion Gear
Bail Joint, 7/16-20
Lock Washer, 3/8
Flat Washer, .51 x 1.12 x .06
Steering Shaft, .625 OD x 24.4
Plastic Bushing, .38 ID
Hex Flange Bearing, 5/8
Shoulder Spacer, .38 ID
Standard Steering Wheel, 13.25
Steering Wheel Cap, Round
LH Axle Assembly, .625 Diameter1"
LH Axle Assembly, .625/.750 Diameters
RH Axle Assembly, .625 Diameter1"
RH Axle Assembly, .625/.750 Diameters
Steel Pivot Bar
Flange Lock Nut, 3/8-16
Cotter Pin
Push Cap, .625
REF.
NO.
31
32
33
34
35
36
37
38
39
40
41
42
43
44
PART
NO.
736-0162
736-0187
736-0316
736-0285
738-1011
741-0659
741-0660
634-0105A
634-0056A
634-0172
734-0255
734-1731
734-0864
734-2290
783-0653E
738-0143
736-0331
710-1260A
731-1869
731-1904
731-0484A
45 719-0399B
719-0525B
46 736-0242
47 710-0643
48 731-1291A
49 731-1649
DESCRIPTION
Flat Washer, .64 x 1.0 x .12
Flat Washer, .64 x 1.24 x .061"
Flat Washer, .78 x 1.589 x .065
Flat Washer, .635 x 1.589 x .06
Shoulder Screw, .5 x 2.2, 3/8-16
Flange Bearing, .632 ID x .937 ODI"
Flange Bearing, .76 ID x .937 OD$
Wheel Assembly, 15 x 6 x 6
Square Shoulder
Wheel Assembly,15 x 6 x 6
Round Shoulder
Rim Assembly Only
Air Valve (Not Shown)
Tire Only, Square Shoulder
Tire Only, Round Shoulder
Deluxe Hub Cap (Ref. 33 Required)
Steering Support Bracket
Shoulder Screw, 3/8-16
Bell Washer, .39 x 1.13 x .062
Self-tapping Screw, 5/16-18 x .75
Deluxe Steering Wheel
Steering Wheel Cap, w/Icon
Standard Hub Cap
(Ref. 33 Not Necessary)
Cast Iron Pivot Bart
Cast Iron Pivot Bars
Bell Washer, .34 x .872
Hex Bolt, 5/16-18 X 1
Pivot Bar End Cap w/Fitting
Pivot Bar End Cap w/o Fitting
1Models equipped with a 42-inch deck.
SModels equipped with a 46-inch deck.
NOTE: Tractor features vary by model NOT all parts listed above and pictured on the previous page are standard equipment.
35