INSTALL H OOD ............. PRODUCT I NFORMATION CARD ........NON-DUCTED FILTERS ..........IMPORTANT SAFETY INSTRUCTIONS ......OPERATING ............PREPARE H OOD LOCATION ........FUSE ............... PREPARE T HEHOOD .......... 6 - 8 CLEANING ............SHARP In s i g h t _M...
Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or consequential economic or property damage.
1. Use this unit only in the manner intended by the FIRE DEPARTMENT. manufacturer. If you have questions, contact Sharp at 2. NEVER PICK UP A FLAMING PAN -- You may be the address or telephone number listed on page 2 of this burned. manual.
PREPARE HOOD LOCATION I Determine whether hood will discharge vertically (3 1/4" WOOD SHIMS 31/4" X 10" x 10" or 7" round), horizontally (3 1/4" x 10" only) or (Recessed-bottom HOR ZONTAL DUCT be non-ducted. For vertical or horizontal discharge, run cabinets only) CABINET FRONT ductwork between the hood location and a roof cap or wall...
PREPARE HOOD NON-DUCTED INSTALLATION - Skip to page 8. 1 Remove 7" Round 7" ROUND DUCTPLATE Duct Plate from top following Steps (6 thru 14) are for DUCTED of hood. Set duct INSTALLATION ONLY. plate aside - with (3) #8 SCREWS LIGHT PANEL mounting screws.
Page 7
PREPARE HOOD 10 Re-install air chute and screw, re-connect wire harness 13 3 1/4" x 10" Ducted Discharge Only: Remove tape from and replace light panel. damper flap and attach Damper/Duct Connector over knockout opening with screws removed in Step 4 under Note: Be careful not to trap wires between Support Fin "PREPARE THE HOOD".
PREPARE HOOD 5. Check that wheel is properly positioned as shown. Non-Ducted Installations Only: Press Sections into place if necessary. Make sure wheel Requires a Performance Ring to be attached to the blower turns freely. wheel. The Performance Ring is packed behind the Teflon :_- Coated Bottom Cover.
• Attach charcoal filters to the aluminum mesh filters. Be • Purchase a set of (2) charcoal filters, model KBK-330, sure that the sides with the blue and yellow stripes are from your local distributor, retailer or from Sharp (see facing down (toward the range top). page 2).
1 FAN There are four fan speeds from low (1) to high (4). Push any button to select one of the four fan speeds. Press Your Sharp Insight Range Hood is equipped with an advanced another button to change fan speed. Push the same button Heat Sensor.
CLEANING To clean hood: Remove filters. Use a damp cloth and To reduce the risk of electric shock, discon- a mild detergent to wipe all grease-laden surfaces. Do not nect from power supply before cleaning. use abrasive cloth, steel wool pads or scouring powder on Aluminum mesh filters: Clean frequently using hot...
Page 12
This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc. ® SHARPELECTRONICS C ORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 RECYCLED PAPER PRINTED IN RSA 626995B...
Page 13
INSTALL H OOD ............. PRODUCT I NFORMATION CARD ........NON-DUCTED FILTERS ..........IMPORTANT SAFETY INSTRUCTIONS ......OPERATING ............PREPARE H OOD LOCATION ........FUSE ............... PREPARE T HEHOOD .......... 6 - 8 CLEANING ............SHARP In s i g h t _M...
Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or consequential economic or property damage.
1. Use this unit only in the manner intended by the FIRE DEPARTMENT. manufacturer. If you have questions, contact Sharp at 2. NEVER PICK UP A FLAMING PAN -- You may be the address or telephone number listed on page 2 of this burned. manual.
PREPARE HOOD LOCATION I Determine whether hood will discharge vertically (3 1/4" WOOD SHIMS 31/4" X 10" x 10" or 7" round), horizontally (3 1/4" x 10" only) or (Recessed-bottom HOR ZONTAL DUCT be non-ducted. For vertical or horizontal discharge, run cabinets only) CABINET FRONT ductwork between the hood location and a roof cap or wall...
PREPARE HOOD NON-DUCTED INSTALLATION - Skip to page 8. 1 Remove 7" Round 7" ROUND DUCTPLATE Duct Plate from top following Steps (6 thru 14) are for DUCTED of hood. Set duct INSTALLATION ONLY. plate aside - with (3) #8 SCREWS LIGHT PANEL mounting screws.
Page 19
PREPARE HOOD 10 Re-install air chute and screw, re-connect wire harness 13 3 1/4" x 10" Ducted Discharge Only: Remove tape from and replace light panel. damper flap and attach Damper/Duct Connector over knockout opening with screws removed in Step 4 under Note: Be careful not to trap wires between Support Fin "PREPARE THE HOOD".
PREPARE HOOD 5. Check that wheel is properly positioned as shown. Non-Ducted Installations Only: Press Sections into place if necessary. Make sure wheel Requires a Performance Ring to be attached to the blower turns freely. wheel. The Performance Ring is packed behind the Teflon :_- Coated Bottom Cover.
• Attach charcoal filters to the aluminum mesh filters. Be • Purchase a set of (2) charcoal filters, model KBK-330, sure that the sides with the blue and yellow stripes are from your local distributor, retailer or from Sharp (see facing down (toward the range top). page 2).
1 FAN There are four fan speeds from low (1) to high (4). Push any button to select one of the four fan speeds. Press Your Sharp Insight Range Hood is equipped with an advanced another button to change fan speed. Push the same button Heat Sensor.
CLEANING To clean hood: Remove filters. Use a damp cloth and To reduce the risk of electric shock, discon- a mild detergent to wipe all grease-laden surfaces. Do not nect from power supply before cleaning. use abrasive cloth, steel wool pads or scouring powder on Aluminum mesh filters: Clean frequently using hot...
Page 24
This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc. ® SHARPELECTRONICS C ORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 RECYCLED PAPER PRINTED IN RSA 626995B...
Page 25
INSTALL H OOD ............. PRODUCT I NFORMATION CARD ........NON-DUCTED FILTERS ..........IMPORTANT SAFETY INSTRUCTIONS ......OPERATING ............PREPARE H OOD LOCATION ........FUSE ............... PREPARE T HEHOOD .......... 6 - 8 CLEANING ............SHARP In s i g h t _M...
Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or consequential economic or property damage.
1. Use this unit only in the manner intended by the FIRE DEPARTMENT. manufacturer. If you have questions, contact Sharp at 2. NEVER PICK UP A FLAMING PAN -- You may be the address or telephone number listed on page 2 of this burned. manual.
PREPARE HOOD LOCATION I Determine whether hood will discharge vertically (3 1/4" WOOD SHIMS 31/4" X 10" x 10" or 7" round), horizontally (3 1/4" x 10" only) or (Recessed-bottom HOR ZONTAL DUCT be non-ducted. For vertical or horizontal discharge, run cabinets only) CABINET FRONT ductwork between the hood location and a roof cap or wall...
PREPARE HOOD NON-DUCTED INSTALLATION - Skip to page 8. 1 Remove 7" Round 7" ROUND DUCTPLATE Duct Plate from top following Steps (6 thru 14) are for DUCTED of hood. Set duct INSTALLATION ONLY. plate aside - with (3) #8 SCREWS LIGHT PANEL mounting screws.
Page 31
PREPARE HOOD 10 Re-install air chute and screw, re-connect wire harness 13 3 1/4" x 10" Ducted Discharge Only: Remove tape from and replace light panel. damper flap and attach Damper/Duct Connector over knockout opening with screws removed in Step 4 under Note: Be careful not to trap wires between Support Fin "PREPARE THE HOOD".
PREPARE HOOD 5. Check that wheel is properly positioned as shown. Non-Ducted Installations Only: Press Sections into place if necessary. Make sure wheel Requires a Performance Ring to be attached to the blower turns freely. wheel. The Performance Ring is packed behind the Teflon :_- Coated Bottom Cover.
• Attach charcoal filters to the aluminum mesh filters. Be • Purchase a set of (2) charcoal filters, model KBK-330, sure that the sides with the blue and yellow stripes are from your local distributor, retailer or from Sharp (see facing down (toward the range top). page 2).
1 FAN There are four fan speeds from low (1) to high (4). Push any button to select one of the four fan speeds. Press Your Sharp Insight Range Hood is equipped with an advanced another button to change fan speed. Push the same button Heat Sensor.
CLEANING To clean hood: Remove filters. Use a damp cloth and To reduce the risk of electric shock, discon- a mild detergent to wipe all grease-laden surfaces. Do not nect from power supply before cleaning. use abrasive cloth, steel wool pads or scouring powder on Aluminum mesh filters: Clean frequently using hot...
Page 36
This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc. ® SHARPELECTRONICS C ORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 RECYCLED PAPER PRINTED IN RSA 626995B...