MTD Yard-Man 247.270190 Operator's Manual
MTD Yard-Man 247.270190 Operator's Manual

MTD Yard-Man 247.270190 Operator's Manual

Internal bagging system 27.5" cutting deck

Advertisement

YaRD-MaN.)//
Operator's Manual
Riding Mower
Internal Bagging System
27.5" Cutting Deck
Model 247.270190
Factory No. 13A-328-402
IMPORTANT:
Read safety rules and instructions
carefully
before operating
equipment.
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-
covered, brush-covered
or grass-covered
land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable
local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws, Federal laws apply on federal lands, A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department,
Ft O. Box 368022 Cleveland,
Ohio 44136-9722,
MTD PRODUCTS
INC. P.O. BOX 368022 CLEVELAND,
OHIO 44136-9722
PRINTED IN U,S.A.
FORM NO, 770-10201A
(11/99)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Yard-Man 247.270190 and is the answer not in the manual?

Questions and answers

Charles Few
April 9, 2025

what type of motor oil do i use with yardman riding mower model 247.270190

1 comments:
Mr. Anderson
April 10, 2025

The specific type of motor oil recommended for the MTD Yard-Man riding mower model 247.270190 is not stated in the provided information.

This answer is automatically generated

Charles Few
April 9, 2025

yardman model 247.270190

1 comments:
Mr. Anderson
April 10, 2025

The MTD Yard-Man model 247.270190 is a riding mower equipped with an internal bagging system and a 27.5-inch cutting deck. It operates with an internal combustion engine.

This answer is automatically generated

Stephen Youle
March 27, 2025

I’ve taken the bolt out of steering wheel now it won’t come off I have whacked it a couple of times with a rubber mallet upwards but it hadnt budged is there something else to loosen ?

1 comments:
Mr. Anderson
May 14, 2025

If the steering wheel is stuck after removing the bolt on an MTD with part number 247.270190, apply upward pressure on the wheel while gently tapping the steering shaft from below with a rubber mallet. Use penetrating oil at the shaft connection if needed. Avoid using excessive force to prevent damage.

This answer is automatically generated

Stephen Youle
March 31, 2025

How do you remove steering wheel

Summary of Contents for MTD Yard-Man 247.270190

  • Page 1 YaRD-MaN.)// Operator's Manual Riding Mower Internal Bagging System 27.5" Cutting Deck Model 247.270190 Factory No. 13A-328-402 IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved...
  • Page 2 TABLEOFCONTENTS Content Page Important Safe Operation Practices ..............Slope Gauge ...................... Assembling Your Riding Mower ................. Know Your Riding Mower ................... Operating Your Riding Mower ................Making Adjustments ..................Servicing Your Rider Mower ................Maintaining Your Riding Mower ................. Off-Season Storage ................... Troubleshooting ....................
  • Page 3 SECTION 1: IMPORTANT SAFEOPERATION P RACTICES This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your rider mower. Failure to comply with these instructions may result in personal injury.
  • Page 4 injury ordeath. A ll slopes require extra caution. If • Before and when backing, look behind and down for small children. you cannot back up the slope or if you feel uneasy on it, do not mow it. • Never carry children. They may fa_loff and be For your safety, use the slope gauge included as seriously injured or interfere with the safe machine operation.
  • Page 5 Grass catcher c omponents aresubject towear, Observe proper disposal laws and regulations. damage and deterioration, which could expose Improper disposal of fluids and materials can harm moving parts or allow objects to be thrown. For your the environment and the ecology. safety protection, frequently check components Prior to disposal, determine the proper method to dispose of waste from your local office of...
  • Page 6 SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING WARNING Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury.
  • Page 7 SECTION 3: UNPACKING & ASSEMBLING YOUR RIDER MOWER • Remove all screws and staples from crate. • Remove both wing nuts securing the battery and Holding the sides of the crate firmly, lift the top part cover to the battery hold-down rods. See Figure 3. of the crate up and keep it aside.
  • Page 8 WARNING: Do not operate the mower if • Tighten the two wing nuts C and D. Check and any one of the grass catcher, discharge make sure that the side-discharge chute is properly chute or mulching plug is not firmly installed and the hardware tightly secured.
  • Page 9 SECTION 4: KNOW YOUR RIDER MOWER Compare the illustrations in Figure 6 with your rider mower to familiarize yourself with the location of various controls and adjustments. The operation of any rider mower can result in foreign objects being thrown into the operator's eyes, causing severe eye damage.
  • Page 10 Before you move the shift lever to any of the CuttingHeightAdjustmentLever positions, depress the brake pedal and stop the Use to raise and lower the cutting deck which unit. Keep your foot on the brake pedal. determines the cutting height. Brake Pedal Use to stop the mower's forward or reverse motion.
  • Page 11 SECTION 5: OPERATING Y OUR RIDER MOWER UsingThrottle/Choke Control • Turn the ignition key to the START position. As soon as the engine starts, let the key return to the The throttle/choke control is used to increase or ON position. decrease the speed of the engine.The FAST and the •...
  • Page 12 • Pivot the hood assembly up. Pull up the • When mowing an area for the first time, watch out grasscatcher bag by the handle and take it to the for objects lying on the grass. If you strike a foreign proper disposal site.
  • Page 13 SECTION 6: MAKING ADJUSTMENTS "Go" Pedal WARNING: Do not at any time make any adjustment to riding mower without first Adjustment to the "Go" Pedal is made at the cable end. stopping engine and disconnecting spark See Figure 9. plug wire, •...
  • Page 14 SeatPosition • If the belt is slipping when you depress the blade engagement pedal about 3/4", loosen the two hex The seat position on the rider mower can be adjusted to nuts on the cable. See Figure 10. maximize the operator's convenience. •...
  • Page 15 Thread the middle nut as far down as possible. Completely loosen, but do not remove, the top hex nut out of the three hex nuts that hold the hex bolt When desired adjustment is reached, retighten the and the ferrule on the deck hanger link assembly. two nuts.
  • Page 16 Using a 9/16" wrench, loosen the hex nut on the Using a 9/16" socket, remove bolt, spacer and the idler pulley. See Figure 13. flat washer from the variable speed pulley. See Remove belt from around deck pulley, idler pulley, Figure 14.
  • Page 17 SECTION 8: MAINTAINING YOUR RIDER MOWER GeneralRecommendations when rotating at high speeds, may cause damage to the mower and/or cause personal injury. • Always observe safety rules when performing any The blade can be tested for balance by balancing it maintenance.
  • Page 18 The spark plug should be cleaned and the gap Blade Assembly reset once a season. Spark plug replacement is • Lubricate blade assembly and deck spindle only recommended at the start of each mowing season. while reassembling the blade either after Check engine manual for correct plug type and gap sharpening or replacement.
  • Page 19 SECTION 9: OFF-SEASON S TORAGE If the machine is to be inoperative for a period longer Battery than 30 days, prepare for storage as follows. • Charge battery fully. The battery loses some of its charge each day when the unit is not used. Rider Mower NEVER store battery without a full charge.
  • Page 20 SECTION 10: TROUBLE-SHOOTING Trouble Possible Cause Remedial Action Excessive vibration Bent or damaged blade Stop engine immediately. Check all pulleys, blade adapters, keys and bolts for tightness and spindle damage. Tighten or replace any damaged parts. Bent blade. Stop engine immediately. Replace damaged blade.
  • Page 21 Dipstick not seated or broken Engine breather defective. Replace. Engine loses crankcase vacuum For repairs beyond those listed in the Trouble-Shooting chart above, please contact an authorized "_w_ service dealer or call Yard-Man Customer Service at 1- (330) 220-4MTD (4683) or 1- (800)-800-7310.
  • Page 22 For instance, if a part numbered 700-xxxx is painted Yard-Man Green, the part number to order would be 700-xxxx-0665. Yard-Man Green: 0665 Yard-Man Yellow: 0674 Powder Black: 0637...
  • Page 23 Model328 ..8 "_ 34 •...
  • Page 24 For instance, it a part numbered 700-xxxx is painted Yard-Man Green, the part number to order would be 700-xxxx 0665 Yard-Man Green: 0665 Yard Man Yellow: 0674 Powder Black: 0637...
  • Page 25 Model328...
  • Page 26 For instance, if a part numbered 700-xxxx is painted Yard-Man Green, the part number to order would be 700-xxxx-0665. Yard-Man Green: 0665 Yard-Man Yellow: 0674 Powder Black: 0637...
  • Page 27 Model328 13 23 1. = Ref. Ref. Part No. Description Part No. Description 683-0152 Pivot Link Assembly 732-0829 Extension Spring 683-0194 Lift Arm Assembly 732-0837 Torsion Spring 710-0376 Hex Screw 5/16-18 X 1.00 Gr.5 736-0119 Lock Washer 5/16 710-3230 Hex Bolt 1/2-13 X 2.75 Gr.5 Special 736-0140 Flat Washer .385 I.D.
  • Page 28 700-xxxx is painted Yard-Man 736-0173 Flat Washer Green, the part number to order would be .28 I.D. x .74 O.D. x .083 700-xxxx-0665. 750-1064 Spacer Yard-Man Green: 0665 Yard-Man Yellow: 0674 "[ransaxle Bracket 783-0591 Powder Black: 0637 783-0433A ShiftLever...
  • Page 29 Model328 X7 9 24 / 23 _ Ref. Part No. Description 683-0147 Idler Bracket Assembly 710-0191 Hex Screw 3/8-24 x 1.25 710-0314 Hex Screw 7/16-20 x 1.0" 710-0902 Cap Screw 3/8-24 x 3.75 710-1611 Pan Head TL Screw 5/16-18 x .75 710-3096 Hex Screw 3/8-16 x 2.0 Special 712-0116...
  • Page 30 Model328 16¸ 31 \\ 25 j Ref. Ref. I Part No. Description Part No. Description No, I 783-0605 Deck Stabilizing Bracket I 726-0272 Clamp: 9/16 dia. 783-0564A Front Frame: Upper 725-0157 Cable Tie 783-0811 Steering Gear Cover 714-0470 Hairpin Clip 683-O264 Front Channel Assembly 714-0147...
  • Page 31 Model328...
  • Page 32 Model328 Ref. Ref. Part No. Description Part No. Description 683-0149B Frame Assembly 731-0708 Battery Cover 683-0190A Oil Drain S_eeve 731-1682A Frame Rail Support: RH 683-0191A 731-1945 Frame Rail Support: LH Engine Duct 683-0192 Muffler Pipe Extension 732-3080 Compression Spring 710-0148 Hex FI.
  • Page 33 For instance, if a part numbered 700-xxxx is painted Yard-Man Green, the part number to order would be 700-xxxx-0665. Yard-Man Green: 0665 Yard-Man Yellow: 0674 Powder Black: 0637 Ref. Part No.
  • Page 34 Model328 Fief. Part No. Description 618-0232 Differential Assembly: Single Speed 618-0248 Drive Shaft assembly: LH Brake 618-0072B Upper Housing Assembly 611-0114 Detent Shaft Assembly 661-0006 Brake Yoke Assembly: LH 710-1206 Hex Washer Hd. TT Screw 1/4-20 x 2.37 Gr .5 710-1325 Hex Washer Hd.
  • Page 35 756-0627 Flat Idler Pulley replacement part. For instance, if a part 783-0463 Idler Bracket numbered 700-xxxx =s painted Yard-Man Green, the part number to order would be 783-0529 Cable Bracket 700-xxxx-0665. 783-0569A Deck Plate Yard-Man Green: 0665 Yard-Man Yellow: 0674...
  • Page 36 Model328 Ref. Part No. DeScription 631-0060 Flow Indicator Assembly 131-0080 Grass Bag Assembly Machine Screw 1/4-20 x 1.0 710-0166 Machine Screw 1/4-20 x 0.5" 710-0286 Hex Screw #10-16 x 0.5" 710-0456 Hex Screw 1/4-20 x 2.75" 710-0564 710-0642 Self-Tapping Screw 1/4-20 x 0.75" Hex Screw 1/4-20 x 3.75"...
  • Page 37 Model328 'l_•\\ "2 Ref. Part No. Description 629-0945 Harness Assembly w/o relays 725-0267 Ignition Switch: 5 Pin 725-1426 Solenoid: 12 V, 100 amp. 725-1462 Seat Switch 725-1643 Spring Switch 725-1657A Interlock Switch 725-1381 Fuse: 20 amp. 725-1726 Battery Cover 725-3237 Battery Cover: Red 729-0125 Connecter...
  • Page 38 YourNotes Date Comments...
  • Page 39 YourNotes Date Comments...
  • Page 40 MANUFACTURER'S LIMITED WARRANTY FOR: YaRD-MaN ,J'#7, e /n c. Routine maintenance items such as lubricants, filters, The limited warranty set forth below is given by MTD blade sharpening and tune-ups, or adjustments such PRODUCTS INC ("MTD") with respect to new merchandise...

Table of Contents

Save PDF