Mitsubishi MSZ-GE15NA Manual
Microprocessor control
Hide thumbs
Also See for MSZ-GE15NA:
- Operating instructions manual (32 pages) ,
- Installation manual (9 pages) ,
- Operating instructions manual (32 pages)
Table of Contents
Advertisement
MSZ-GE06NA
MSZ-GE09NA
MSZ-GE12NA
MSZ-GE15NA
MSY-GE09NA
MSY-GE12NA
MSY-GE15NA
MSY-GE18NA
[ WIRELESS
REMOTE
CONTROLLER
I E.g.:MSZtype
_Signal
transmitting
section'_
Operation
display
section
_--
_
OPERATE/STOP
_
(ON/OFF)
button
ITemperature
buttons
.)
!
r
,,_.m
EL_CnaC
Ok_,,dl O0-EI
,
_,TJ
c_o_ AMPM
l*i ® I-/_gJ
TOO _i'j TOO
ON/OFF W_ML_OOOL
MSZ-GE18NA
TOO
('i_ TOO
ON!OFF
WARM _I}COOL
©®®
"FAN_ SPEED
-
ECONO
COOL
button
.
(VANECONTROL
RESET button
Indication of
remote controller
model is on back
_OFF
TIMER button
ON T,MER
button
____TIME
SET buttons
1
FORWARD
button
BACKWARDbutton
CLOCK
SEt button
NOTE: Last setting wilt be stored after the unit is turned OFF with the remote controller. Indoor unit receives the signal of the
remote controller with beeps.
[INDOOR
UNIT DISPLAY
SECTION
1
Operation Indicator lamp
The operation indicator at the right side of the indoor unit indicates the operation state.
• The following indication applies regardless of sha)e of the indication.
Indication
0
÷
Operation state
The unit is operating to
reach the set temperature
The room temperature is
approaching the set tem-
perature
Standby mode
(Only during multi system
operation)
Room temperature
About 4°F(2°C) or more
away from set tempera-
ture
About 2 to 4°F(1 to 2°C)
from set temperature
",_- Lighted
"O,' _- Blinking
©
Not lighted
10
Advertisement
Table of Contents
Related Manuals for Mitsubishi MSZ-GE15NA
Summary of Contents for Mitsubishi MSZ-GE15NA
- Page 1 MSZ-GE06NA MSZ-GE09NA MSZ-GE12NA MSZ-GE15NA MSZ-GE18NA MSY-GE09NA MSY-GE12NA MSY-GE15NA MSY-GE18NA [ WIRELESS REMOTE CONTROLLER I E.g.:MSZtype _Signal transmitting section'_ ,,_.m EL_CnaC ('i_ TOO ON!OFF WARM _I}COOL Ok_,,dl O0-EI ©®® _,TJ c_o_ AMPM Operation display section l*i ® I-/_gJ ON/OFF W_ML_OOOL TOO _i'j TOO OPERATE/STOP (ON/OFF) button...
-
Page 2: Cool, Dry, Heat, Fan Operation
8-1. COOL ( 0 ) OPERATION (1) Press OPERATE/STOP (ON/OFF) button. OPERATION INDICATOR lamp of the indoor unit turns ON with a beep tone. (2) Select COOL mode with OPERATION SELECT button. (3) Press TEMPERATURE buttons (TO0 WARM or TOO COOL button) to select the desired temperature. The setting range is 61 ~ 88°F (16 ~ 31°C). - Page 3 (4)Theinitial settemperature isdecided b ytheinitial room temperature. Model Initial room temperature Initial settemperature 79°F (26°C) ormore 75°F (24°C) COOL m ode of "1 FEEL C ONTROL" 77to79°F (25to26°C) Initial room temperature minus 4 °F(2°C) DRY mode of Less than79°F (25°C) "1 FEEL C ONTROL"...
-
Page 4: Auto Vane Operation
8-7. AUTO VANE OPERATION 1. Horizontal vane (1) Vane motor drive These models are equipped with a stepping motor for the horizontal vane. The rotating direction, speed, and angle of the motor are controlled by pulse signals (approx. 12 V) transmitted from indoor microprocessor. (2) The horizontal vane angle and mode change as follows by pressing VANE CONTROL button. - Page 5 (10) ECONO C OOL ( _) operation (ECONOmical operation) When ECONO C OOL b utton ispressed i nCOOL mode, settemperature isautomatically set4°F(2°C) higher. Also thehorizontal vane swings i nvarious c ycle. SWING operation makes y oufeel c ooler t han settemperature. So, e ven though t hesettemperature ishigher, theair conditioner cankeep comfort.
-
Page 6: Smart Set
8-9. SMART SET (_) OPERATION 1. How to SET SMART SET operation (1) Press OPERATE/STOP (ON/OFF) button. (2) Select COOL, HEAT(MSZ) or ECONO COOL mode. (3) Press SMART SET button. (4) Set the temperature, fan speed, and airflow direction for SMART SET operation. NOTE: •...
Need help?
Do you have a question about the MSZ-GE15NA and is the answer not in the manual?
Questions and answers
The top indicator light continues to blink and the bottom light is not on. Cannot figure out what the problem is and don’t see this indicator on your map in manual
When the top indicator light blinks and the bottom light is off on a Mitsubishi MSZ-GE15NA, it indicates that the unit is operating and trying to reach the set temperature, but the room temperature is still about 4°F (2°C) or more away from the set temperature.
This answer is automatically generated