MTD 609 Operator's Manual page 35

REF.
NO.
2
3
4
5
6
7
8
9
10
11
12
PART
NO.
710-0604A
783-0726A
783-0727
783-0728
710-0514
711-1408
711-1409A
!712-0240
;712-0241
712-0431
712-0459
13 712-3004A
14 717-1550D
15 717-1554
16 723-0448A
17 736-0169
18 736-3084
19 738-1001A
20 741-0475
21 741-0656
22 738-0372A
23 631-0027
24 731-0220
25 !638-0019
638-0021
i
26 638-0020
638-0022
27 1683-0128A
28 1712-0431
29 1714-0470
_0214
DESCRIPTION
Self-tapping Screw, 16-18 x .625
RH Pivot Support Bracket
LH Pivot Support Bracket
Pivot Bar Bracket
Hex Cap Screw, 3/8-16 x 1 (Grade 5)
RH Drag Link
LH Drag Link
Jam Nut, 7/16-20 (Grade 2)
Hex Nut, 3/8-24 (Grade 2)
Flange Lock Nut, 3/8-16
Flange Lock Nut, 7/16-20
Flange Lock Nut, 5/16-18
Steering Gear, 11/90 Ratio
Steering Pinion Gear
Ball Joint, 7/16-20
LockWasher, 3/8
Flat Washer, .51 x 1.12 x .06
Steering Shaft, .625 OD x 24.4
Plastic Bushing, .38 ID
i Hex Flange Bearing, 5/8
Shoulder Spacer, .38 ID
Standard Steering Wheel, 13.25
Steering Wheel Cap, Round
LH Axle Assembly, .625 Diameter1-
LH Axle Assembly, .625/.750 Diameter'j:
RH Axle Assembly, .625 Diametert
RH Axle Assembly, .625/.750 Diameter:l:
Steel Pivot Bar
Flange Lock Nut, 3/8-16
Cotter Pin
i Push Cap, .625
tModels equipped with a 42-inch deck.
:[:Models equipped with a 46-inch deck.
REF.
NO.
31
32
33
34
35
36
PART
NO.
736-0162
736-0187
736-0316
736-0285
738-1011
741-0659
741-0660
634-0105A
634-0056A
634-0172
734-0255
734-1731
734-0864
37 734-2290
38 783-0653D
39 _738-0143
40 736-0331
41 710-1260A
42 731-1869
43 731-1904
44 731-0484A
719 0399B 45 i -
719-0525B
46 736-0242
47 710-0643
48 731-1291A
49 731-1649
Models 607, 608 & 609
DESCRIPTION
Flat Washe_ .64 x 1.0 x .12
Flat Washer .64 x 1.24 x .061"
Flat Washez .78 x 1.589 x .06:1:
FlatWasher .635 x 1.589 x .06
Shoulder Screw, .5 x 2.2, 3/8-16
Flange Bearing, .632 ID x .937 OD t
Flange Searing, .76 ID x .937 OD:I:
Wheel Assembly, 15 x 6 x 6
Square Shoulder
Wheel Assembly,15 x 6 x 6
Round Shoulder
R m Assembly Only
IAir Valve (Not Shown)
Tire Only, Square Shoulder
Tire Only, Round Shoulder
Deluxe Hub Cap (Ref. 33 Required)
Steering Support Bracket
Shoulder Screw, 3/8-16
IBell Washer, .39 x 1.13 x .062
,Self-tapping Screw, 5/16-18 x .75
Deluxe Steering Wheel
Steering Wheel Cap, w/Icon
Standard Hub Cap
(Ref. 33 Not Necessary)
Cast ron Pivot Barl-
Cast Iron Pivot Bar'l:
iBell Washer, .34 x .872
Hex Bolt, 5/16-18 X 1
Pivot Bar End Cap w/Fitting
Pvct Bar End Cap w/o Fitting
NOTE: Tractor features vary by model. NOT all parts listed above and pictured on the previous page are standard equipment.
35