Advertisement
ou need to make sure
that the TV is set to pick
up either Cable TV stations
or Antenna
signals.
In other
words, the TV needs to know
whether you have connected
a Cable TV signal or a nor-
real antenna
to its ANTENNA
plug (see page 2).
NOTE:
If you went through
First 77me Setup (page 3),
this task has already
been
completed
for you.
Press MENU • or •
on the TV (or on the remote
press M button and then M
A•
buttons.)
Select the word CABLE with
the TV's on-screen Arrow.
,,7_
the (+) or (-) but-
tons (on the TV or the remote)
to select either:
YES-
If you DO have Cable
TV connected
to the
TV. Channels
1-125
can be selected.
NO-
If you have an Antenna
connected to the TV.
Channels 2-69 can be
selected.
Press STATUS button on
the remote control to clear the
screen.
Try it out.
Press the CHAN-
NEL A•
buttons
and scan the chan-
nels. CH••
works
only after STATUS
button is pressed to
clear the screen (or
Menu times out -
about 1 minute.)
Remember,
to set
the TV to select the
channels on your
Cable system, or in
your area, see the
"Autoprogram" and
"Adding Channels"
in the section
below.
uto-Program
is tor
adding
local area chan-
nel numbers
into the memory.
of the TV. This makes it easy
for you to select only your
area (or Cable system)
chan-
nels when the CHANNEL
_k • buttons
are pressed.
NOTE:
If you went through
First Time Setup (page 3),
this task has already been
completed
for you.
Press MENU • or •
on the TV (or on the remote
press M button and then M
A•
buttons.)
Select the word PROGRAM
with the TV's on-screen Arrow.
I ,<__the
(+) button (on
l<
the TV or the remote) to PRO-
GRAM.
_Press
the (+) button again
to start the TV search for area
channels.
Flashing
channel
numbers
will
count upward on the screen
as
the TV looks for channels
to
"ADD".
_)You may press any button
(on the TV or remote) to stop
the channel search at any time.
When the channel search is
completed the TV will return to
the last viewed channel.
The TV screen will be blocked
off until the search for channels
is done.
"RED" channel numbers
have been
added to the TV's memory.
"WHITE"
channel numbers are not
in the TV's program memory,
_Try
it out. Press
l_/
CHANNEL
••
buttons
1,"_7/"
and
see
which
channels
I
_
have been added.
To drop any unwanted channels
from the TV's memory, see
how to "Manually" delete
channels in the section below.
When searching for channels the
TV screen display may jitter
slilghtly. This is normal and does
not indicate a need for service.
uto-Program
(see above)
adds all the channels
it
can find (on your Antenna
or
Cable TV s)'stem) into the
TV's memo_. . Add/Delete
channels
makes it easy for
you to add other channels,
or
drop unwanted
channels,
from the list of channels
in
the TV's memo_.'.
Press MENU • or •
on the TV (or on the remote
press M button and then M
• • buttons,)
Select the word CHANNEL
with the TV's on-screen Arrow.
_
P-r-_s Channel Number
buttons on the remote (or
CHANNEL ••
buttons on the
TV) to select the channel you
want to SAVE (or DELETE.)
Press the STATUS button
_Press
(+) button to SAVE [ _
the selected channel number
I
to clear the screen after adding
into memory.
I I or
d eleting) all the channels
Press (-) button to DELETE a t
[.you want.
channel from memory.
1
NOTE: You can also add the VCR/AUX mode
(see page 7) into the TV's channel memory.
Then you can quickly select the Audio/Video
Input jacks on the rear of the TV by pressing
the Channel AY buttons.
Just "SAVE" the VCR/AUX
rood.• (located
between the lowest and highest charnel
num-
bers) into the TV's channel memo ry.
Try it out. Press
NNEL•,
or •
buttons and "scan 'from
I
_
channel to channel.
The channels you SAVED
should appear. The channels
you DELETED should not
appear.
7['0SAVE a channel above 100,
use the CHAr
buttons on the
TV. The remote number buttons
only go up to channel 99.
Advertisement
