Panasonic P2HD AJ-HPX3100 Manual page 9

Return Video, Tally
AG-YA500G
Remote Cable
VF interface Box
(bundled to AG-CA300G)
G/L
HD/SD SDI
AJ-HPX3100
Control Unit, which enables full control over image adjustments and
recording, teams with the lightweight, compact, and highly mobile
AG-CA300G Camera Adaptor.
*Power can be supplied only when the AG-BS300 Base Station is driven by an AC power
source. A separate power cord is also required between the AG-BS300 Base Station and the
AG-CA300G Camera Adaptor.
Remote Control-Ready
The AG-EC4G Extension Remote Control Unit or AJ-RC10G Remote
Control Unit* offer both studio use and direct connection to the
AJ-HPX3100. This lets you adjust the images and control the camera
operation while viewing the monitor.
*The remote control unit can control only functions supported by the
AJ-HPX3100. It cannot control unsupported keys or dials.
10P Cable (10 m (33feet) / 50 m (164 feet))
Camera Image
AJ-HPX3100
Remote Control
HD/SD SDI Output Terminals and Down-Converter
Two video line output terminals (BNC) are provided as standard
equipment and flexibly support monitoring and line recording. The
built-in down-converter outputs high-quality SD video signals for
broadcasting use. The aspect mode can also be selected.
•SDI OUT (HD/SD): Can also output signals with embedded audio.
Backup recording operation can be interlinked with the Rec Start/
Stop controls of an HD-SDI input-equipped Panasonic recorder, such
as the AG-HPG20, etc. The AJ-HPX3100 can also output down-
converted SD-SDI from an HD source.
•MON OUT: Can output HD SDI/SD SDI/Composite. HD signals can
be down converted.
VIDEO OUT
SDI OUT
SDI (HD/SD)
AJ-HPX3100
Standard HD/SD SDI Input Terminals
The AJ-HPX3100 supports line recording through the SDI input
terminal; thus, it can be used as a portable recorder. It supports
1080/59.94i, 1080/50i, 480/59.94i and 576/50i input signals.
*The input signal must be in the same format as the recording format of the camera recorder.
List of proxy data supported by the AJ-YDX30G video encoder board
Recording Mode File Format
SHQ 2CH MOV* MOV
1
HQ 4CH MOV* MOV
1
HQ 2CH MOV* MOV
1
LOW 2CH MOV MOV
STD 2CH MP4
MP4
(default)
*1: These modes can not be selected when the P2 card recording mode is set to SD. *2: Only this mode can be selected when the P2 card recording mode is set to SD (NTSC/PAL). *3: Total
recording rates and recording times are reference values which were obtained from continuous recording using our products. Actual recording time varies depending on the recorded scenes
and the number of clips. *The use of DCF Technologies is under license from Multi-Format, Inc.
AG-CA300G
Camera Adaptor
Power supply
G/L, Return Video, Tally
HD/SD SDI
Bound Cable made by Canare Electric
V2PCS25-5CFWCE-SF-SC (25 m / 82 feet)
Headset
V2PCS50-5CFWCE-SF-SC (50 m / 164 feet)
(produced by
V2PCS100-5CFWCE-SF-SC (100 m / 328 feet)
another manufacturer)
AJ-RC10G Remote Control Unit or
AG-EC4G Extension Control Unit
Analog Composite
AG-HPG20
P2HD Portable
Recorder
Video
Resolution Codec
960×540 H.264 High Profile
640×360 H.264 High Profile
640×360 H.264 High Profile
(1080) 480×270
H.264
(NTSC) 352×240* 2
Baseline Profile
(PAL) 352×288*
2
MPEG-4
320×240
Simple Profile
Bound Cable made by Canare Electric
max. 100 m / 328 feet
Genlock Terminal for Return Video Signal Input
Return video signal (analog HD-Y signal) input to the GENLOCK IN
terminal or HD/SD video signal (HD/SD SDI signal) input to the SDI IN
terminal can be viewed on the viewfinder.
*The input signal must be in the same format as the recording format of the camera recorder.
XLR Audio Input with Automatic Switching Function
The 2-channel XLR audio input terminals on the rear panel are
compatible with a +48 V phantom power supply. The new automatic
front/rear switching function automatically selects the rear input
signal when input is connected to the rear terminal.
USB 2.0 Interface
The AJ-HPX3100 incorporates the Host and Device USB 2.0 as
standard connectors. In Device mode, a P2 card slot can be used as
Monitor
an external PC device. In Host mode, an external hard disk drive can
be connected, making it easy to copy data from the P2 card to HDD.
VBS
The thumbnails of stored video in HDD also can be viewed.
AJ-HPX3100
TC IN, TC OUT Terminals
The AJ-HPX3100 has a built-in SMPTE time code generator/reader.
TC IN and OUT terminals make time code throughput possible. This
permits an external time-code lock.
Other System Functions and Options
• UniSlot ® wireless receiver compatible (2 channels).
* UniSlot® is a trademark of Ikegami Tsusinki Co., Ltd.
• Anton/Bauer light connector on the top (lower front side of the
handle).
• Equipped with earphone terminals (stereo mini-jack) and speaker.
• Multiple battery support, including Anton/Bauer or IDX batteries*.
Monitor
* The V-mount battery plate is required for IDX batteries.
Compatibility with Nonlinear Editing Systems
There are many nonlinear editing products in the market that already
support P2. P2 native editing makes it possible for you to maintain
high-quality video and a flexible editing workflow.*
* For information on compatible nonlinear editing systems, visit <https://eww.pavc.
panasonic.co.jp/pro-av/> and click "Nonlinear Compatibility Information." For the operating
requirements and other details of editing software, visit the website of the relevant software
manufacturer.
Bit Rate channel
3500 kbps 2CH
1500 kbps 4CH
1500 kbps 2CH
800 kbps 2CH
1500 kbps 2CH
AG-BS300
Base Station
SDI
G/L Return Video/Tally
AJ-RC10G Remote Control Unit or
AG-EC4G Extension Control Unit
USB 2.0 (HOST)
File Copy
USB 2.0 (DEVICE)
Upload
Audio
Total Record Rate*
Codec
Linear PCM Approx. 5060 kbps
AAC-LC Approx. 1780 kbps
AAC-LC Approx. 1650 kbps
AAC-LC Approx. 950 kbps
AAC-LC Approx. 1650 kbps
BT-LH2550
LCD Video Monitor
Headset
(produced by
another manufacturer)
HDD
NLE
Recording Time*
3
3
(per 1GB)
Approx.25 min.
Approx.72 min.
Approx.78 min.
Approx.135 min.
Approx. 78 min.
8