Download Print this page
Kenmore 272.98201.490 Owner's Manual
Kenmore 272.98201.490 Owner's Manual

Kenmore 272.98201.490 Owner's Manual

Sewing machine cabinet

Advertisement

Quick Links

$EWRNG
MACHgNE
CABINET
OWNER'S
MANUAL
Model Number
272.98200.490
Oak
272.98201.490
White
ASSEMBLY
PARTS LIST
IMPORTANT:
Read instructions
before assembling.
98200-FC
98201-FC

Advertisement

loading

Summary of Contents for Kenmore 272.98201.490

  • Page 1 $EWRNG MACHgNE CABINET OWNER'S MANUAL Model Number 272.98200.490 272.98201.490 White ASSEMBLY PARTS LIST IMPORTANT: 98200-FC Read instructions before assembling. 98201-FC...
  • Page 2 TO ORDER REPLACEMENT PARTS CALL 1-800-366-7278 Notice to Customer: Before beginning assembly, remove all parts from the PLEASE NOTE: To assure proper handling of replacement parts please include the following information: carton. Check closely with illustrations below to determine that all the parts are included. Model Number of Unit - 98200.490 (Oak)
  • Page 3: Hardware Included

    #6x5/8" Brass Panhead Screws Hardware Included (1) Metal Handle _1198200 only),_'_ #8xl/2" Panhead Screws 121) Cams White Plastic (4) Knobs 98201 only #5xl/2" Flathead Screws (98200 Metal) _ (32) #6x1" Flathead Screws (98201 Ceramic) Allen Key (2) #6x1" Panhead Screw (98201) (16) #8x5/8"...
  • Page 4: Cabinet Assembly

    Understanding H owthe "ARROW-LOC"CamFastenerWorks. ARROW TOWARDS HOLEIN EDGE 1. Position bolt in 2. Press cam into 3. Insert bolt through 4. To lock, rotate cam pre-drilled hole and pre-drilled hole until pre-drilled hole in until tight, using turn until tight, flush with surface, edge of panel.
  • Page 5 Place parts shown below on a flat surface and press cam into pre-drilled holes provided Step 2. (as illustrated In FIG. 2). After cams have been inserted (21 total), you may now attach the eight (8) drawer runners using (32) #6x1" Flathead Screws (FIG. 2A). After attaching the runners, insert the wood dowels (6) in the Front Assembly, Front Brace and Back Brace, (as shown in FIG.
  • Page 6 Step 3. Attach Front Brace to Filler Strip on back side of Front using (3) 1-1/2" Screws. Be sure to position Brace as shown, cut-out down. Attach the Handle with (2) 4.7 mm Bolts for Metal or (2) #6x1" Panhead Screws for White Plastic Handle to the Front. Attach Rubber Bumpers to the Front Brace using (2) #6x5/8"...
  • Page 7 Step 6. Attach Partition by guiding the Connecting Bolts into holes in the Back Brace, Back, and Front Assembly; also allow Dowels FIG. 6 in the Front Assembly and Back Brace to enter holes in the Partition (as shown in FIG.
  • Page 8 NOTE: The following assemblies should be done with Cabinet upright. Step 9. Attach Hinges to Leaf Supports with (4) #8x518" Flathead screws each, FIG. 8 tap Magnet with hammer, (as shown in FIG. 8A). Attach Bronze Strikes to outside of Left and Right sides with #5xl/2" Flathead Screw as in FIG.
  • Page 9 Assembling the Drawer BeginDrawerassemblyby insertingDrawerConnectors into the endsof the (4) DrawerBacks. (asshown in FIG.A). PushConnectorsall the wayintothe DrawerBackuntil the tabs lock into place. Drawer Back- E Drawer sD;;:ec Drawer Connectors Side - B III/ Orawer Assemb,y Ill / I iv STEP'1.
  • Page 10 CONGRATULATIONS Your Sewing Cabinet is Now Ready for the Machine 98200-9 Page 9 98201-9...
  • Page 11 Installing Sewing Machine in your new Cabinet. It may be helpful to read the directions for operating the mechanism before proceeding with the following steps. See page 11, and FIG. 12, on this page. STEP 1. To prevent damage to Cabinet surface, place cushioning material just to the left of cut-out.
  • Page 12 Operating the Mechanism in your Cabinet To move from FLATBED POSITION TO To move your machine from FREE-ARM position to FLATBED position: (See FIGS. 13, 14 and 15). FREE-ARM position: (See FIG. 13, 14 and 15.) (1.) Lift and tilt machine slightly forward. (1.) Remove INSERT (2.) Rotate release lever to the right, (clockwise) to (2.) Lift and tilt machine slightly backwards.
  • Page 13 Wood Parts List Top Aaaembly (D) Hinge Rail (J) Right (I) Left o:Ooo \<C, T0p ° o (E; Platform (A) Right Leaf (B) Left Leaf Leaf Supports /o _ /ooo/LI //,..,_ ooo: eft Side Panel (F) Partition (H) Right Side Panel (RightV, ew) // °...
  • Page 14: Other Parts List

    OTHER PARTS LIST •0,==, ® (D) Mounting (E) Zinc Flat (F) Wing (G) Round (B) Connecting (C) Rubber Bolts Washers Magnet Bolts Bumper (A) Cam (K) #8xl/2" (L) Knob (M) #8x5/8" (N) #5x1/2" Panhead Screw Flathead Flathead Screw (H) Leaf Screw Screw (98201)
  • Page 15 Other Parts List and Numbers Ref. No, Ref. No. Description Part No. Description Part No. 19ram Cam 000709 Platform Hinge 002533 Connecting Bolts 002892 Leaf Hinge 002733 Rubber Bumpers 002466 Bracket Right 000151 Bracket Left Mounting Bolts 002890 000150 Zinc Flat Washers 000220 Hinge Left 000152...
  • Page 16 API Specialty Furniture (A Division of ARROW PRODUCTS, Inc.) P.O. Box 410, Elkhorn, Wl 53121 1-800-533-7347 12-98 98200-BC 98201-BC...

This manual is also suitable for:

272.98200.490