Yamaha JUNIOR KIT Assembly Manual page 2

Before you use, please thoroughly read this Assembly Manual and use the drum set in a safe and proper manner.
■ Drum Set Components
● JK6F41AMK
Snare Drum
Bass Drum
■ Setting Up
When making adjustments to your settings always make sure to loosen the fixing bolt.
Parts will suffer damage if the part is adjusted with force when the fixing bolt is tightened.
● Front View
Cymbal Stand
Clamp
Floor Tom
Bass Drum
● Back View
Hi-Hat Stand
Drum Stool
■ Drum Stool Assembly
1.
Extend the Legs, slide the Leg Base to the end of the Base Section.
2.
Insert the Upper Tube Section into the Leg Base's Joint Section
(Make sure the tooth on the position clamp is facing down).
3.
After adjusting the height of the Upper Tube Section, firmly tighten the Wing
Bolt on the Base Section.
4.
Loosen the Wing Nut on the Position Clamp on the Upper Tube Section,
align the Position Clamp with the Joint and tighten the Wing Nut. With the
Position Clamp set in place, the stool will be set to the same height every
succeeding time the stool is assembled.
5.
Attach the Seat to the Upper Tube Section and tighten the Wing Bolt.
6.
Repeat steps 3 and 4 to adjust the stool height.
● If the stool is used in a high position, make sure that the Upper Tube Section is in-
serted at least 6cm into the Leg Base's Joint Section. The line on the upper pipe indi-
cates the minimum required depth.
● Do not loosen the bolt that fixes the Leg in place marked with a "
become unstable causing an accident resulting in injury.
Thank you for purchasing the Yamaha "JUNIOR KIT" drum set.
Tom Tom
Floor Tom
Clamp
Cymbal Stand
Tom Tom
Snare Drum
Snare Stand
❈ Cymbals are
optional
Foot Pedal
". The stool may
● JK6F42CMK
Foot Pedal
Drum Stool
■ Bass Drum Assembly
1.
Place the head then the hoop onto the shell. Use the bass drum bolts, washers and the bass
drum hooks to secure the head and the hoop to the shell by tightening each bolt gradually in a
diagonal fashion.
2.
Loosen the bass drum leg bolts and rotate the bass drum legs, (Fig. A) then loosely secure the
leg in place. Once you have determined the position of the leg, tighten the bass drum bolts to
secure the leg in place. (An alignment gauge is supplied on the bass drum leg base and bass
drum leg to aid in setting leg angles.)
To adjust the leg length, loosen the bass drum length key bolt (Fig. B) with a tuning key, adjust
the length of the leg, and firmly tighten the length key bolt.
Rotate the leg rubber either direction to secure the rubber to the bass drum leg. (Fig. C)
3.
Insert the clamp into the pipe clamp and firmly tighten the tom-holder bolt.
Washers
Bass Drum Bolts
Tuning Key
Hoop
(C) Rotate the rubber tip either direction
to fix in position.
Bass Drum Leg
Rubber Tip
Seat
Position Clamp
Drum Key Bolt
Hexagonal Nut
Upper Tube
Section
6cm
Line
Snare Stand Hi-Hat Stand
Pipe Clamp
Bass Drum Leg Bolt
Clamp
Clamp Bolt
Shell
(B)
Tuning Key
Head
Bass Drum Length
Key Bolt
● Attaching the BD Riser
(Plate for FP Attachment)
Insert the BD riser into the pipe
clamp and tighten the bolt.
❈ After the position has been deter-
mined, set the memory clamp.
Wing Bolt
Wing Bolt
Base Section
Cymbal Stand X2
Pipe
Clamp
(A)
Memory
Clamp
BD Riser
Joint
Leg
Leg Base