32cc/1.9 cu.in. 2-cycle 17 inch cutting path / 0.095 inch line gasoline brushwacker (52 pages)
Summary of Contents for Craftsman 358.795690
Page 1
Operator's Manual I CRAFTSMAN°I 18cc/1.1 cu. in. 2-Cycle GASOLINE HEDGE TRIMMER Model No. 358.795690 - 18" Blade WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon-Sat;...
Page 2
Parts and Ordering Back FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GAS POWERED HEDGE TRIMMER For one (1) year from the date of purchase, when this Craftsman Gas Powered Hedge Trimmer is maintained, lubricated, and tuned up according to the operat-...
Page 3
• Move at least 10 feet (3 meters) _WARNING: Failure to follow all away from fuel and fueling site before Safety Rules and Precautions can re- starting engine. sult in serious injury. OPERATE YOUR UNIT SAFELY KNOW YOUR UNIT • Inspect unit before each use for •...
• Use only recommended Craftsman spark a rresting screen. Ifyou operate cutting blades and replacement ahedge trimmer inastate orlocale parts; use ofany other parts m ay where s uch regulations exist, you are void your warranty and cause d am-...
Drain the gas tank, start the quality 2-cycle air-cooled engine oil. engine and let it run until the fuel lines We recommend Craftsman brand oil. and carburetor are empty. Use fresh Mix gasoline and oil at a ratio of 40:1 fuel next season.
OPERRATING POSITION ..Switch Protection &_'_ ..Eye 3. Slowly press the primer bulb 6 times. 4. Move the choke lever to FULL STOPPING YOUR E NGINE CHOKE. • To stop engine, move s witch toOFR Choke BEFORE STARTING THE ENGINE •...
Page 7
NOTE: If engine dies with the choke NOTE: If engine has not started, pull lever at the OFF CHOKE position, move starter rope 5 more pulls. If engine still the choke lever to HALF CHOKE and does not run, it is probably flooded. Proceed to STARTING A FLOODED EN- pull the rope until the engine runs.
REPLACE SPARK PLUG Cleaning the airfilter: Adirty airfilter d ecreases engine per- Replace spark p lug each y ear t oen- formance and increases fuel consump- sure theengine starts e asier and runs tion and harmful emissions. Always better. Set s park p lug gap at0.025 i n. clean a fter e very 5hours o foperation.
• Turn IDLE screw clockwise to in- ing high speed adjustments as damage crease idle speed. tothe engine can occur. Adjust the high • Turn IDLE screw counterclockwise speed screw 1/1 6 of a turn at a time. A 1/16 turn is about the width of the slot in to decrease idle speed.
• Replace spark plug with new one of recommended type and heat range. at least 5 minutes after adding stabilizer. • Clean air filter. Craftsman 40:1,2-cycle engine oil (air • Check entire unit for loose screws, cooled) is already blended with fuel nuts, and bolts.
YOUR WARRANTY RIGHTS AND OB- ment engine to a Sears authorized repair LIGATIONS: The U. S. Environmental center as soon as a problem exists. Protection Agency and Sears, Roebuck Warranty repairs should be completed in a reasonable amount of time, not to ex- and Co., U.S.A., are pleased to explain the emissions control system warranty ceed 30 days.
Page 12
HOW TO FILE A CLAIM: If you have in the performance of any warranty any questions regarding your warranty maintenance or repair on emission re- rights and responsibilities, you should lated parts will be provided without contact your nearest authorized service charge to the owner if the part is under center or call Sears at 1-800-473-7247.