Advertisement
D.AS SIST HANDLE
ASSIST
HANDLE
•
Drop threaded end of screw "D.'; through the
opening in the top of the T-handle.
Figure 7.
•
Pull on the threaded end ofscrew"D."
to bring
the square head of the screw past the pin inside
the T-handle.
Figure 7.
•
Align the assist handle between the safety la-
bel and the end of the :tube, Figure 6.
Make
sure hex recession in assist handle is on the left
side of the tube ..........
•
Seat nut "E." in thehex,shaped
recession on
the back side of the assist handle.
•
Insert thethreaded
end of the T- handle screw
through the
hole in the assist
handle
and
tighten fn_rdy by hand
only.
illll
E.TRIMMER
HEAD
_
_-
i_
•
Place dust cup "H." over the hex nut on the bot-
....... tom of the tube -see
illustration.
The hex nut
should fit completely
inside dust cup "H.".
•: Hold dust cup "H." with a wrench to keep the ar-
bo r shaft from t_arning.
•
Thread the trimmer
head onto the arbor shaft
=_ age_st
dust cup "H." and hand tighten fnm_ly.
_:
Unless trimmer
head is tightened
ade-
quately, it can unthread when engine is started or
': ;stopped.
If this situation
occurs, reinstall
the
trimmer head and tighten more securely.
!
!
•• -
Figure
6
Befm'e Assembly
Top, View
,
'_emhled
.
, L.__.2.t in ,,
Figure 7
i,,,,
H,,,,,,,,
Hi ,m '
i
i,m
ii
,
....
Arbc
Hex
t_
Laf
Nut --o
i
i Dust
CupH.
:Direction
toInstall
Useawrenchtokeepthe i
spinning
the
trimmer
head onto the unit.
i
ill,
E SHIELD
ATTACHMENT
A WARNING
The
shield
must
be
properly
installed.
The
shield
provides
partml
protection
from the risk
of t]iro_obj_cts
to theoperator
and:others
and
is eqmpped
with a line limiter
which
cuts excess
: ....
line to the proper
length.
:
• _ .......
mii
imiil
I II H IIIIIIIIIIIII
illlliH
iil
i
A WARNING
F_lure
to install
shield
inthe
position
shown
in
Figure
8can
result
in semous
injury
to the op-
erator.
The length
of the shield
must be aligned
with the length
of the tube. Direct
widest
part of
shield
toward
engine.
The line limiter
(on the underside
of
the shield)
is sh_.and
can cut you.
•
Match key (raised area) on the shield with the
"V" slot on the tube. Figure 8.
•
Rest bottom of shield ontop of shoulder (not on
the dust cup) of tube. Figure 8.
NOTE:
The bottom of shield must rest on top of
the shoulder of the tube and not on dust cup.
. !
•
Install bracket
"G. °'and screws "C." as shown
in Figure 8.
:, _
:i
:
NOTE: Alt,hough a screwdriver
slot is provided in
screws "C.,, it is easier to install the screws
with a wrench or socket.
•
Tighten the screws evenly and securely.
_:
It is possible that a small space will be left
between bracket
"G." and the shield when the
screws are fi_y tightened.
Widest Part
_
Bracket G.
of Shield Toward
Engine
Screws C.
Figure 8
.._7
m
Advertisement
