Advertisement
How to use the Ulficouple
Before operating
your
dishwasher
the first time...
Attach the Faucet
Adapter. The
special faucet adapter supplied
with your dishwasher must be
assembled
to the sink faucet before
you can use your dishwasher.
The faucet adapter is designed to
fit standard spouts having internal
or external threads. You will find
the adapter and two washers in the
"Faucet Adapter" packet in your
dishwasher.
To install faucet adapter, first
remove the old aerator or trim ring
on your faucet spout.
If faucet has external
threads:
®
Insert the thinner of the two
washers into the faucet adapter and
attach it to the faucet spout.
If faucet has internal
threads:
J
J
N
How to connect the
Unicoup|e
1. Pull Unicouple and its hoses
completely out fi'om storage
compartment
located at rear of
rlich
.....
h,ar _.a o.,_oh it to the
faucet adapter.
t
J
2. Attach the Unicouple connector
to the faucet adapter by depressing
collar at the top of the connector.
When Unicouple is all the way up
onto the adapter, release the collar.
It will then snap into position to
lock the Unicouple in place.
The Unicouple's
small hose carries
water from the faucet to the
_1_- _1 ......
L
_
l
i
.
msnwasncr.
Its
nose carries
large
drain water to the sink. Be sure
Unicouple
is pointing toward the
sink bowl drain opening and the
sink drain is open for water that
"";" drain €..........
_,;,r, ..... ,....
if your dishwasher
drains into a
disposer, operate the disposer unti!
it is completely
empty before
starting the dishwasher.
3. Turn hot water fully on before
starting the dishwasher.
Insert both washers into the faucet
adapter
and attach it to the faucet
spout.
If the faucet
adapter
threads
do not match
your faucet spout,
JULII
l_l_,O.l
IIO.I_J'vWOJl_/
IJl
_JILIIIIUIII_
supply store normally
has
additional
fittings to adapt your
faucet spout to the specia! faucet
adapter.
NOTE." A sink spray attachment
hose can burst if it is installed on
the sanw sink with your dishwasher
I,Vesuggest that you discomwct
the
Oilily
OIL1*
t4..)"
LIIII.{L_gIII_V._Ill
{]
.VUII/
,lltlF_
has one and plug the hole.
How to use the
Faucet-Flo
nozzle
J
-----2_
PRESSURE
Li-Z__
RELEASE
/_._
_@
BUTTON
The Faucet-F!o
nozzle is part of the
Unicouple
connector.
Operate
the
nozzle by depressing
the pressure
release button on the front of the
T r_: ......
1,.
Will
!IItLI
umcuupJc
connector.
You ....:" _:--'
the Faucet-Flo
nozzle useful for
severa! reasons, For example:
I
l
• It allows you to flush cold water
uut.... of the .or
............
watcl line so that
you can better regulate your water
temperature.
• It allows you to test the
temperature
of the water before
starting your dishwasher.
How to disconnect the
Unicouple
from faucet
auapter
1. Turn off the hot water.
2. Release the water pressure by
depressing
the pressure release
button.
J ms
relieves
water
pressure and protects you, and the
room, from severe splashing.
3. Release Unicouple
from faucet
by depressing
the collar at the top
of the Unicouple
connector.
How to disconnect
your
dishwasher
1. Remove the power cord plug
from the wall receptacle.
2. Disconnect
Unicouple
from
faucet adapter.
NOTE: When motor stops at the
end of the final rinse, the Unicouple
can be disconnected
and returned to
storage.
How to drain excess water
g'M_ g31l!_
If the sink is 34" or higher flom
the floor, the excess water in
Unicoup!e
hoses cannot be drained
directly
into the sink. It will be
necessary
to drain excess water
from hoses into a bowl or suitable
container
that is held outside and
lower than the sink.
12
Advertisement
