Advertisement
Programming Continued ...
Manual Liquid Dispensing Mode
Manual Liquid Dispensing Mode
Manual Liquid Dispensing Mode
Manual Liquid Dispensing Mode
Manual Liquid Dispensing Mode
This feature sets up the SD2 unit to dispense coffee only as long as the user holds down the selected PUSH button.
As soon as the user stops pressing the button, coffee stops flowing into the cup. Setting the unit for Manual Liquid Dispense will turn off the
Portion Control Dispense Mode.
Enter
Enter Program Mode –
Enter Program Mode –
Enter Program Mode – press and hold STOP/W
Enter Program Mode –
Enter Program Mode –
Program Mode
are blinking.
Set Manual Dispense –
Set Manual Dispense –
Set Manual Dispense –
Set Manual Dispense –
Set Manual Dispense – While you are in the programming mode, press and hold the PUSH button.
Select Manual
Hot liquid will start to flow.
Liquid Dispense
Continue to hold down the PUSH button until liquid stops
At this time, you have selected the Manual Liquid Dispensing Mode and have exited out of the programming mode.
Stop & Exit
Confirm/Reset
Confirm/Reset T T T T T empera
Confirm/Reset
empera
empera
Confirm/Reset
Confirm/Reset
empera
emperature
These features allow you to check the heating tank temperature or change the temperature if desired. The temperature in the tank is
programmable from 170°F, in 2 degree increments up to 204°F .
T T T T T o Confirm
o Confirm T T T T T empera
o Confirm
o Confirm
empera
empera
ture.
ture.
o Confirm
emperature.
empera
ture.
ture. Press and hold STOP/WASH button for approximately 2-3 seconds. When the READY light
starts blinking. Lift off from STOP/WASH button. Each blink equals 2ºF, starting with 170ºF, to a maximum of 204ºF.
T T T T T o Change
o Change T T T T T ank
o Change
o Change
ank T T T T T empera
ank
ank
empera
empera
ture
ture
o Change
ank
emperature
empera
ture
ture
Enter
Enter
Enter T T T T T empera
Enter
Enter
Enter
start "quick flashing".
Temp. Program
T T T T T o Change
o Change T T T T T empera
o Change
o Change
o Change
Change
2ºF. Release STOP/WASH when desired temperature is reached.
Tank Temp.
T T T T T o Set and Exit,
o Set and Exit, press either of the PUSH buttons.
o Set and Exit,
o Set and Exit,
o Set and Exit,
Set & Exit
LOW
LOW
LOW TEMPERA
LOW
LOW
TEMPERA
TEMPERA
TEMPERATURE LOCKOUT (DEL
TEMPERA
TURE LOCKOUT (DEL
TURE LOCKOUT (DEL
TURE LOCKOUT (DELT T T T T A): A): A): A): A):
TURE LOCKOUT (DEL
the unit at a temperature as low as 195º F. Delta two will allow you to dispense at a temperature as low as 185º F. Delta three does not limit the minimum
operating temperature. The Cafe system comes from the factory with a Delta three setting. To make adjustments enter Program Mode:
1. Press and hold Stop/Wash button, until all lights on the control panel are blinking, about 10 seconds. Release button.
2. While in the Program Mode, press and hold Stop/Wash button the READY light will begin blinking, continue to hold the Stop/Wash button. The READY
light will stop blinking. Continue holding Stop/Wash button until the READY light comes back on in a longer, 3 second glow.
3. Now release the Stop/Wash button The READY light will now blink a pattern of flashes indicating current delta setting.
4. To change the setting, press and hold the Stop/Wash button for about three seconds until you receive a short flash. Release the button and you will
add one blink to the delta pattern or continue holding to add two blinks.
5. To set press any other button. The unit will return to normal operation with the new delta lockout setting.
ture
ture
ture
ture
empera
empera
ture Program Mode.
ture Program Mode.
emperature Program Mode.
empera
ture Program Mode.
ture Program Mode. Press and hold STOP/WASH button. READY light will
emperature.
empera
empera
empera
ture.
ture.
ture. Continue holding STOP/WASH button. Each quick flash equals
ture.
This mode will give you a choice of two minimum operating temperatures. Delta one allows you to operate
DELTA ONE (one long glow, followed by one blink) allows you to run the coffee dispense at five degree below maximum.
DELTA TWO (one long and two blinks) allows you to run the coffee dispense at 15 degrees below maximum.
DELTA THREE (one long and three blinks) allows you to operate the unit at any temperature.
STOP/WASH
STOP/W
STOP/W
STOP/W
ASH for about ten [10] seconds until all lights on the control panel
ASH
ASH
ASH
stops flowing, then release the button.
stops
stops
stops
Temperature Settings
Number of
Blinks
Temperature
1
170ºF
2
172ºF
3
174ºF
4
176ºF
5
178ºF
6
180ºF
7
182ºF
8
184ºF
9
186ºF
10
188ºF
11
190ºF
12
192ºF
13
194ºF
14
196ºF
15
198ºF
16
200ºF
17
202ºF
18
204ºF
3
Advertisement
