Advertisement
Steps to Programming
Y Y Y Y Y our Curtis Cafe System is F
our Curtis Cafe System is F
our Curtis Cafe System is Factor
our Curtis Cafe System is F
our Curtis Cafe System is F
WARNING HOT LIQUID, Scalding
may occur. Avoid splashing.
Place an empty container under the
dispensing nozzles while programming.
All programming is performed at the control
panel (illustration, right).
The Hot Water button is used for only for
dispensing hot water and does not require any
programming. Water is dispensed as long as the Hot Water button is held down.
The STOP/WASH BUTTON has several functions. This button is used to stop a Portion Control dispense cycle. It is used to wash out the
mixing and dispensing systems and it is used to enter programming functions.
Product % Ra
Product % Ra
Product % Ratio tio tio tio tio
Product % Ra
Product % Ra
This controls the amount of dry product that is metered from the hoppers. This can be programmed from 10% to 100% of the capacity of
the dispensing system. By counting LED flashes you can determine the product % ratio currently set for this dispense button (see table).
Enter Program Mode –
Enter Program Mode –
Enter Program Mode –
Enter Program Mode – press and hold STOP/W
Enter Program Mode –
Enter
lights start blinking.
Program Mode
T T T T T o program Product % Ra
o program Product % Ra
o program Product % Ra
o program Product % Ra
o program Product % Ratio,
Enter
one second, then release. The current setting will be indicated by LED flashes.
Product % Ratio
T T T T T o change the product thro
o change the product thro
o change the product thro
o change the product thro
o change the product throw w w w w , , , , , press and hold the button until light starts quick flashing. Each quick flash increases
Change
the amount by 10%. Release the button when the desired throw amount is achieved. After releasing the button, the
Product Throw
number of blinks represent the new setting.
Exit
T T T T T o exit the P
o exit the P
o exit the Po o o o o wder Dispensing Mode,
o exit the P
o exit the P
Program Mode
P P P P P ortion Control Liquid Dispensing Mode
ortion Control Liquid Dispensing Mode
ortion Control Liquid Dispensing Mode
ortion Control Liquid Dispensing Mode
ortion Control Liquid Dispensing Mode
This program adjustment allows you to setup the machine to automatically dispense a preset volume of coffee. When the user makes a
PUSH button selection, the SD2 unit dispenses only the volume of coffee programmed by the Portion Control Dispensing Mode. By setting
the unit for Portion Control Dispensing, you have locked out the manual dispense feature.
Enter Program Mode –
Enter Program Mode –
Enter
Enter Program Mode –
Enter Program Mode – press and hold STOP/W
Enter Program Mode –
Program Mode
Select & Change
T T T T T o select & change the P
o select & change the P
o select & change the P
o select & change the P
o select & change the Portion Control Dispensing
Preset Liquid
selected PUSH button until the liquid begins to flow, then release. The timing starts when liquid begins to flow.
Dispense
Stop flo
Stop flo
Stop flo
Stop flow and Exit –
Stop flo
dispensing.
Stop & Exit
You have now set the timing for this button and have exited the programming mode. Pressing the selected
dispense button now will provide the liquid volume that you just set. To reset the timing, you must start again by
entering the programming mode.
2
actor
actory Pre-Set for Optimum P
actor
actor
y Pre-Set for Optimum P
y Pre-Set for Optimum P
y Pre-Set for Optimum Performance.
y Pre-Set for Optimum P
COFFEE
DISPENSE
tio,
tio,
tio,
tio, press and hold the selected PUSH button for approximately
wder Dispensing Mode,
wder Dispensing Mode, push the other PUSH button.
wder Dispensing Mode,
wder Dispensing Mode,
ortion Control Dispensing V V V V V olume
ortion Control Dispensing
ortion Control Dispensing
ortion Control Dispensing
w and Exit –
w and Exit –
w and Exit – When the desired volume is achieved, press this PUSH button once again to stop the
w and Exit –
erformance.
erformance. Usually this Does Not Change.
erformance.
erformance.
Usually this Does Not Change.
Usually this Does Not Change.
Usually this Does Not Change.
Usually this Does Not Change.
HOT WATER
DISPENSE
STOP/W
STOP/W
STOP/W
STOP/WASH
ASH
ASH
ASH for about ten [10] seconds until all
ASH
STOP/W
STOP/W
ASH
ASH
STOP/W
STOP/WASH
ASH for about ten [10] seconds until all lights start blinking.
ASH
olume
olume
olume – while in the programming mode, press and hold the
olume
STOP/WASH
COFFEE
BUTTON
DISPENSE
Number of
Flashes
1
2
3
4
10
Volume
10%
20%
30%
40%
100%
Advertisement
