Table of Contents
Advertisement
Do Not
Remove
Numbers
CarreSDOnd
to steljs.
9
n
Remove
the two rear corner
posts located at the
back of the
washer/dryer*
Remove the two
rear
comer
posts
I
corner pieces
attached
to the lower
front of the
washer/dryer.
DO Not
remove the foam
shipping pieces
between the washer
and dryer until the
washer/dryer
is in place,
10
n
Move
foam shipping
pieces outward
just enough to
clear the washer
lid. Open the
washer lid. The
latch under the
dryer will hold lid open.
Pull
ig$&
p
. .
-- .-;
shipptng straps.
Slide washer/dryer
onto cardboard
or
hardboard before moving across floor to
ovoid damaging floor covering.
19
1" 1
m It you have room to work from
either side of the washer/dryer!
move
4
washer/dryer
close to final posltlon SO
Lv\
YO
you can easily complete the following
steps. (Go to srep zu.)
steps. (Go to Step 20.)
If yiu are working in a closet or
recessed area, move the washer/dryer
into final position and remove
cardboard/hardboard
from under
washer/dryer,
Remove the two foam
shipping pieces between the washer
and dryer and place with the other
shipping pieces. Remove the two
Phillips-head screws located at the top
of the access panel. (.%?e illustration for
Step 25.) Remove access panel and set
access panel and screws aside.
Complete the following steps through
the access area.
v
3
shipping
straps
11.
I
m iRead
the yellow
card. Place hand on top Of
agitator when removing
the shipping straps. Firmly
jerk, then pull the three
shipping straps up until
each strap with key is
completely
removed from
washer. Put straps in the same
area as other shipping pieces.
--
w
16
m Attach hose to bottom (hot
water) inlet valve opening first; then
second hose to top (cold water) inlet
valve. Tighten couplings by hand. Use
pliers to make an additional two-thirds
turn.
IMPORTANT: THIS PROCEDURE
MUST BE FOLLOWED TO ASSURE
PROPER INSTALLATION.
/
clamp
12
8 Remove
yellow card. Take
hoses out of basket.
Place hoses with
other parts.
20
l
Put n hook" end of drain hose
into laundry tub or standpipe. Check for
proper length of drain hose.
connector
17
mTo prevent the drain hose
from coming 'off or leaking, it must be
installed per the following instructlons:
1, Wet the inside end of the drain hose
with tap water. DO NOT USE ANY
OTHER LUBRICANT.
2. Squeeze ears of drain hose clamp
with pliers to open and place Clamp
over the end of the drain hose.
3. While holding clamp open, work end
of drain hose onto drain connector
4. Position clamp over the drain hose
area marked "clamp. n Release
clamp. Clamp should be l/4 Inch
from end of drain hose.
i7
in
l
Before attaching
water inlet
hoses, run water through both faucets
into a bucket. This will get rid of particles
in water lines that might clog hoses.
Mark which is the hot water faucet.
Mark whicn IS Tne not WaTer TUUC;GI.
13
n
Release washer lid
by pushing up on latch. Close lid,
i GM
Attach bottom inlet hose
(inlet marked 'H") to hot water faucet;,
Attach top inlet hose (inlet marked UC )
to cold water faucet. Tighten couplings
to the faucets by hand, Use pliers to
14
m Disconnect the power supply.
Connect power supply cord or cable to
dryer. See "Electrical connection, *
Panels B and C, Do Not plug power
supply cord into outlet or reconnect
power at this time.
Use new hoses and washers that came
with your washer/dryer.
make final two-thirds turn.
3Q
_.
Ic
C
Sl
18
n
Standpipe or
laundry tub drain system:
Open yellow clamp and
slide over "hook" end of
drain hose to secure the
rigid and corrugated
sections together.
Floor drain system: Do
Not install "hook" end of drain hose t0
corrugated
section, Consult your
plumber for proper installation.
I
I
15
coupling
washer
l
Insert a flat washer into each
end of the inlet hoses. Check that
washers are firmly seated in couplings.
Panel E
Advertisement
Table of Contents
