Table of Contents
Advertisement
UNIVERSAL
REMOTE
CONTROL
PROGRAMMING
YOUR
REMOTE
If you are using Zenith products, the remote is programmed for
the most commonly used codes. For other brands -- or if your
remote fails to control your Zenith products -- you will have
to program the remote.
Follow these steps for each product you are using:
1. Look up the three-digit
code for your brand (such as
Zenith) and type of equipment (such as VCR) in the
code table on the following
page.
2. Press and hold PRG with a small blunt object until
the indicator lights (about three seconds).
3. Press TV, VCR, CABLE,
or AUX to select the prod-
uct you want your remote to control. (Use CABLE
or AUX, to program your remote for a second TV or
VCR or to program your remote for a video disc
player or audio equipment.)
4.
Key in the three-digit code for your equipment,
then
press ENTER/TUNE.
The indicator light should
flash, then turn off to'indicate
that the code was ac-
cepted. If the indicator stays on, repeat steps 3 and 4
or try using a different code.
5. Write the codes that operate your equipment on the
label inside the battery compartment
for future
reference.
To erase all code programming and return to the factory preset
codes, key in code 9-1-1 when programming the remote.
NOTES:
• The remote cannot be programmed while in the StarSight
mode: Choose TV, VCR, CABLE or AUX mode before
pressing PRG.
• If no key on your remote is pressed within 60 seconds, the
programming process will stop, and you will have to start
again.
• You may cancel programming at any time by pressing PRG.
SPECIAL
FEATURES
AUX+I, AUX+2, AUX÷3 Capability
Your remote can control up to seven electronic components. If
you have programmed the remote for four components using the
'IV, VCR, CABLE and AUX keys, you may also program it for
up to three additional components (AUX+I, AUX+2, AUX+3)
by holding the AUX key and pressing the 1, 2 or 3 key during
programming. Once programmed, hold down the AUX key and
press 1, 2 or 3, to access the additional AUX +1, 2 or 3 mode.
Cable Box Volume
You may use your remote to control cable box volume and mut-
ing if available on your equipment. First program your remote
with the brand code for your cable device using the CABLE or
AUX key. Then repeat the programming steps, again using the
CABLE or AUX key, but key in code 3--9-9 instead of a brand
code.
To restore TV volume/mute control to the CABLE or AUX
mode, reprogram your cable code into that mode.
Amplifier
Volume
Override
You may use your remote to override
your TV, VCR or video
disk player's
volume functions with your amplifier's
volume and
muting.
1.
Program
your amplifier
code
into the CABLE
mode
or one of the AUX
modes.
2.
Select
the mode
on your remote
(TV,
VCR,
etc.)
where
you want the amplifier
volume
control
func-
tion to appear.
In other
words,
if you want
to oper-
ate the volume
and mute
of your amplifier
while
the
remote
is in TV mode,
press
TV for this step.
3.
Begin
the programming
steps
as described
in "Pro-
gramming
Your
Remote"
and enter
code
4-9-9,
fol-
lowed
by ENTER.
The amplifier volume and mute features are now available in the
current mode.
To restore normal volume and muting control to your TV,
VCR, cable or laser disc player, repmgram
the remote for these
units into each mode (TV, VCR, etc.) to be restored.
NOTE:
• CD and tape devices will automatically
select amplifier
vol-
ume and mute.
_18-ol-o
4 -- 4
Advertisement
Table of Contents
