Advertisement
_>
-0
-0
m
Z
i
X
156
APPENDIX
11. Sharpness
(Command:
k k)
To adjust screen sharpness.
You can also adjust sharpness
in the Picture
menu.
Transmission
[k][k][
][Set
ID][
][Data][Cr]
Data Min: O0 - Max: 64 (*transmit by Hexadecimal
code)
_Refer to 'Real data mapping'.
Acknowledgement
[k][
][Set
ID][
][OK/NG][Data][x]
12. OSD Select
(Command:
k I)
To select OSD (On Screen
Display) on/off.
Transmission
[k][I][
][Set
ID][
][Data][Cr]
Data 00: OSD off
Data 01: OSD on
Acknowledgement
[I][
][Set
ID][
][OK/NG][Data][x]
13. Remote
Control
Lock Mode
(Command:
k m)
To lock the remote
control
and the front panel con-
trols on the set.
Transmission
[k][m][
][Set
ID][
][Data][Cr]
Data 00: Lock off
Data 01: Lock on
Acknowledgement
[m][
][Set ID][ ][OK/NG][Data][x]
If you're not using the remote control
and front panel
controls
on the TV, use this mode.
When main power
is on/off,
remote
control
lock is released.
If Key Lock is on in the standby
mode, TV will not turn
on by POWER
button
of remote
control
and on the
TV.
14. Treble (Command:
k r)
To adjust treble.
You can also adjust treble
in the Audio
menu.
Transmission
[k][r][
][Set
ID][
][Data][Cr]
Data Min: O0 - Max: 64 (*transmit by Hexadecimal
code)
_Refer to 'Real data mapping'.
Acknowledgement
[r][
][Set
ID][
][OK/NG][Data][x]
15. Bass (Command:
k s)
To adjust bass.
You can also adjust bass in the Audio
menu.
Transmission
[k][s][
][Set ID][
][Data][Cr]
Data Min: O0 - Max: 64 (*transmit by Hexadecimal
code)
_Refer to 'Real data mappingt
Acknowledgement
[s][
][Set
ID][
][OK/NG][Data][x]
16. Balance
(Command:
k t)
To adjust balance.
You can also adjust balance
in the Audio
menu.
Transmission
[k][t][
][Set
ID][
][Data][Cr]
Data Min: O0 - Max: 64 (*transmit by Hexadecimal
code)
_Refer to 'Real data mappingt
Acknowledgement
[t][
][Set
ID][
][OK/NG][Data][x]
17. Color Temperature
(Command:
x u)
To adjust color temperature.
You can also adjust color temperature
in the Picture
menu.
Transmission
[x][u][
][Set
ID][
][Data][Cr]
Data Min: O0 - Max: 64 (*transmit by Hexadecimal
code)
_Refer to 'Real data mapping'.
Acknowledgement
[u][
][Set
ID][
][OK/NG][Data][x]
18. Energy
Saving
(Command:
j q)
To control
the
energy
saving
function.
Transmission
[ j ][q][
][Set
ID][
][Data][Cr]
Data
00:
Energy
saving
- off
01: Energy
saving
- Minimum
02:
Energy
saving
- Medium
03:
Energy
saving
- Maximum
04:
Energy
saving
- Auto
(depending
on
model)
05:
Energy
saving
- Screen
off
Acknowledgement
[q][
][Set
ID][
][OK/NG][Data][x]
19. Auto Configuration
(Command:
j u)
To adjust picture
position
and minimize
image
shak-
ing automatically.
Auto
configuration
only works
in
RGB-PC
mode.
Transmission
[j
][u][ ][Set
ID][ ][Data][Cr]
Data 01: To set
Acknowledgement
[u][ ][Set
ID][ ][OK/NG][Data][x]
20. Channel Tuning
(Command:
m a)
To tune channel to following physical/major/minor
number.
Transmission
[m][a][
][Set
ID][ ][DataO0][
][Data01]
[ ][Data02][
][DataOS][
][Data04][
][DataOS][Cr]
Digital
channels
have a Physical,
Major,
and Minor
channel
number.
The Physical
number
is the actual
digital
channel
number, the Major is the number
that
the channel
should
be mapped
to, and the Minor
is
the sub-channel.
Since the ATSC tuner automatically
maps the channel
to the Major number,
the Physical
number
is not required
when sending
a command.
Data 00: Physical Channel
Number
NTSC air: 02 - 45, NTSC cable: 01, OE - 7D
ATSC air: 01 - 45, ATSC cable: 01 - 87
Data 01 & 02: Major Channel
Number
Data 01: High byte
Data 02: Low byte
Two bytes are available
for the Major and Minor,
normally
only the second
byte is used.
Data 03 & 04: Minor Channel
Number
Not needed
for NTSC.
Advertisement
