Download Print this page

Advertisement

SEARS
OWNER'S
MANUAL
MODEL NO.
315.275120
CAUTION:
Read and follow
ALL safety rules
and instructions
before operating
this equipment.
I:RRI:TSHRN °
Industrial
Laminate Trimmer
Double Insulated
Thank You For Buying A
Craftsman Laminate
Trimmer
Warranty
Rules For Safe Operation
Introduction
Table Of Contents
Unpacking
Features
Adjustments
Operation
Maintenance
Repair Parts
SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A.
972000-336
11-00
Printed in U.S.A.

Advertisement

   Summary of Contents for CRAFTSMAN 315.275120

  • Page 1

    Features Warranty Adjustments Rules For Safe Operation Introduction Operation Maintenance Table Of Contents Thank You For Buying A Repair Parts Unpacking Craftsman Laminate Trimmer SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. 972000-336 11-00 Printed in U.S.A.

  • Page 2: Warranty

    INDUSTRIAL LAMINATE TRIMMER If this Craftsman Industrial Laminate Trimmer fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE IN THE UNITED STATES.

  • Page 3

    WARNING: WARNING: Do not attempt to operate this tool until you have The double insulated system is intended to protect thq 'user from shock resultingfrom a break in the tool's read thoroughly understand completely internalwiring. Observe all normal safety precautions instructions, safety rules, etc.

  • Page 4: Rules For Safe Operation

    Sharp alcohol, or any medication. cutters minimize stalling and kickback. WHEN SERVICING ONLY IDENTICAL KEEP HANDS AWAY FROM CUTTING AREA. CRAFTSMAN REPLACEMENT PARTS. Keep hands away from cutters. Do not reach POLARIZED PLUGS. To reduce risk of underneath work while cutter is rotating. Do not electric shock, this tool has a polarized plug (one attempt to remove material while cutter is rotating.

  • Page 5: Table Of Contents

    Congratulations and thank you for buying this Craftsman laminate trimmer. It has been designed, SPECIFICATIONS: engineered and manufactured to provide you with Sears high standard of dependability, ease of operation, and operator MaximumCutterDiameter 1-3/8 in. safety. Properly cared for, it will give you years of rugged, trouble-free performance.

  • Page 6: Unpacking

    Your trimmer has been shipped completely assembled and ready for use. After removing it from the carton, inspect it WARNING: carefully to make sure no breakage or damage has occurred during shipping. Ifany parts are damaged or missing, contact If any parts are missing, do not operate your trimmer until your nearest Sears Retail Store to obtain replacement parts the missing parts are replaced.

  • Page 7: Adjustments

    ON-OFF SWITCHOFF USH CAP DEPTHOF BASE HOUSING WING BOLT WRENCH(2) COLLETNUT COLLET 'SUBBAS_ Fig. 1 WARNING: ,WARNING: Your laminate trimmer should never be connected Do not use cutters that are larger in diameter than to power supply when you are assembling parts, the opening in trimmer...

  • Page 8: Installing/removing Cutters

    INSTALLING/REMOVING cu'rrERS See Figure 2. WRENCHON • UNPLUG YOUR TRIMMER. COLLETNUT WARNING: Failure to unplug your trimmer could result in accidental starting causing serious injury. • Place your trimmer upside down on a workbench in order to gain easy access to spindle and collet nut. •...

  • Page 9: Operation

    WARNING: Always wear safety goggles or safety glasses with side shields when using your trimmer. Failure to do so could result in dust, shavings, chips, loose particles, or foreign objects being thrown into your eyes resulting in possible serious injury. If the operation is dusty, also wear a face or dust mask.

  • Page 10: Force Feeding

    FORCE FEEDING Clean, smooth laminate trimming and edge shaping can be done only when the cutter is revolving at a relatively high speed and is taking very small bites to produce tiny, cleanly severed chips. If your trimmer is fomed to move forward too fast, the speed of the cutter becomes slower than normal in relation to its forward movement.

  • Page 11: Direction Of Feed And Thrust

    TRIMMERFEED WARNING: DIRECTION If desired depth of cut is greater than can be safely cut in one pass, make cuts in two or three passes. DIRECTION OF FEED AND THRUST See Figures 7 and 8. The trimmer motor and cutter revolve in a clockwise direc- tion.

  • Page 12: Extension Cords

    EXTENSION CORDS WARNING: The use of any extension cord will cause some loss of power. To keep the loss toa minimum and to prevent tooloverheating, use an extension cord that is heavy enough to carry the Check extension cords before each use. If damaged current the tool will draw.

  • Page 13: Maintenance

    WARNING: been found that they are subject to accelerated wear and possible premature failure, as the fiberglass chips and When servicing use only identical Craftsman replacement grindings are highly abrasive to bearings, brushes, parts. Use of any other parts may create a hazard or commutators, etc.

  • Page 14: Exploded View Andparts List

    CRAFTSMAN INDUSTRIAL LAMINATE TRIMMER - MODEL NUMBER 315.275120 SEE NOTE"A" NOTE: "A" - The assembly shown represents an Important part of the Double Insulated System. To avoid the possibility of alteration or damage to the System, service should be performed by your nearest Sears Repair Center.

  • Page 15

    CRAFTSMAN INDUSTRIAL LAMINATE TRIMMER - MODEL NUMBER 315.275120 ---. The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your LAMINATE TRIMMER or when ordering repair parts.

  • Page 16: Parts Ordering / Service

    For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night www.sears.com...

Comments to this Manuals

Symbols: 0
Latest comments: