Advertisement
_
tt"_l iZ_
|L'i [,."_J'LTi,
J
Instructions
for the CLone Programmer to Learn the Master LEOV54S Setup.
Use MPT CabLe to Connect LT2002 CLone Programmer to
Master L20V54S MPI Port
if there is a good connection, "THE CLONEHASCONTROL O FTV" message
wiLLappear. Pressany key on the InstaLLerremote.
Learn
Setup
from
Master
L20V54S
Press 1 to select the "LEARN FROM TV" option,
then press ON/OFF,
POWER,or ENTER to go to the Memory Bank Selection Menu. Pick the
Memory "Bank" you want to store the master L20V54S's setup in by
pressing either Channel key repeatedly to choose Memory 1, 2 or 3.
(If you choose a Memory "Bank" that has a master device's setup
programmed into it, that setup wi[[ be overwritten
by the new master
L20V54S's setup.)
Once the Clone memory bank is selected, press
ON/OFF, POWER, or ENTER. The Clone memory bank you have selected
wi[[ be shown. Press ON/OFF or POWERto begin copying the master
L20V54S's setup.
THE CLONE HAS CONTROL OF THE TV
Set the CLock (OptionaL)
Set the time on a Master TV's Clock. (If the time has already been
copied from a TV into the Clone programmer, you can set a master
TV's dock by copying the time from the Clone programmer.)
The
THE CLONE IS VERSION
XX
THE TV IS VERSION
XX
THE SW IS REVISION
XX
CLONE CLOCK=
XX:XX
TV CLOCK=
XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
This menu should appear by itself after the
LT2002 is connected
to the L20V54S MPI port.
CLONE SELECTION
MENU
Clone Programmer can copy the current time to both a master TV and
to the Clone's internal
dock,
accurate to within
one minute. (Another
reason that the Clone programmer
should be equipped with fresh,
high-quality
alkaline batteries,
is for it to keep the time as accurately
as possible.)
Since the Clone Programmer'stime cannot be set directly, the current
time needs to be copied from a Zenith/LG TV equipped with M.P.I.
input capability.
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK
FROM TV
(4) SET TV CLOCK
FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
- TO CHANGE
MENU ITEMS, PRESS
CHANNEL
KEYS OR DIGITS.
- TO EXECUTE
ITEM, PRESS ON/OFF,
POWER, OR ENTER
After the time is copied to the Clone programmer, the current time
can then be transferred
to another TV. (This can be a master TV, or
another TV which has already had the features
set up.)
*Note:
When using the done
programmer
for teaching
or teaming,
be sure that the heartbeat pattern
is shown on the LEDs. Both learning and
teaching should take about 45 or more seconds depending on the complexity
of the master setup. White the clone is functioning, do not move it or otherwise
disturb the clone or wiring connections.
If the clone _nishes
the function
in less than
45 seconds, redo the function
again. Press the reset button
if the clone does not act
normally.
LT2002
CLone Programmer
Communication
ProbLems
• A stowJ%shing
green light indicates
there are communication
problems
between
the L20V54S and the LT2002 clone
programmer.
If this is the case, check for a damaged cable,
poor contacts,
or other connection
troubles.
• If the status indicator
is red, the programmer
batteries
are
tow and should
be replaced. Install
4 high-quality
alkaline AA
batteries.
PAG E 43
Advertisement
