Safety Instructions CAUTION CAUTION: To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with ar- The exclamation point within a triangle'is intended to tell is intended to tell the user the user that important oper- that parts inside the product...
14. I!anoutside antenna isconnected t othetelevision e quipment, besuretheantenna system isgrounded s oastoprovide some protection a gainst voltage surges andbuiltupstatic charges. IntheU.S. S ection 8 10oftheNational Electrical Code andinCanada Part1 oftheCanadian Electrical Code provides i nformation withrespect toproper grounding o fthemast andsupporting s tructure, grounding of the lead-inwireto an antenna discharge unit,sizeof grounding conductors, location ofantenna-discharge unit,connection t ogrounding e lectrodes, andrequirements forthegrounding e lectrode.
Introduction Congratulations on Your New Purchase Your new video component features an all solid state chassis which is designed to give you many years of enjoyment. It was thoroughly tested and adjusted at the factory for best performance. In order for you to take full advantage of your new video component, please read and follow the installation and operating instructions supplied with this product.
Installation Location Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the sc Feen. Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or moisture. Do not position magnetic equipment (motors, fans, other speakers, etc.) nearby. Optional External Equipment...
Antenna/Cable Connections Antenna Connection - For proper reception of VHF/UHF channels an external antenna is required. For best reception an outdoor antenna is recommended. Antenna Mode must be set to TV. (Refer to Antenna Mode section.) Indoor Outdoor Incoming Cable From Home Antenna (75 Ohm) Typical VHF/UHF Antenna VHF/UHF...
Control Operation Power Channel Change- (Two options) - Press the POWER button to turn ON. Press again to turn OFF. Option POWER Press the CHANNEL (CH) UP or DOWN button to sequentially scan through programmed channels (while On Screen Menus are not displayed). Located On Remote Control Selects Next - Press the VOLUME (VOL) LEFT or RIGHT...
Recall Press the RECALL button to review: Skip Feature - Press the SKIP button repeatedly • Audio Mode status to set the Skip Timer for a desired length of time up to 3 • CH Number or Video Input selected minutes.
Main Menu (Icons) EX,T I [ ,NPUT I____ _-_ IPIOTUREI I AUD'O I _1 , CAPTION TIMER I SET_UP I _'-'_ Located On Remote Control Selects Desired Feature When Menu is Displayed Selects or Adjusts Features When Menu is Displayed ACTION Displays and Exits Menus Press the ACTION button to display the Main Menu with Icons.
Color, Tint, Brightness, Picture & Picture Adjustments Sharpness Adjustments • Color Press the ACTION button to display the Main Menu. • Tint Press the CH DOWN button to select the Picture • Brightness • Picture Icon. • Sharpness Press the ACTION button to display the Picture •...
Game Guard Game Guard (Lockout) - Prevents video games and other video sources from being viewed. Channel 3, 4 and all video inputs are locked out for 12, 24 or 48 hours. NOTE: Be sure to understand this feature before ACTION attempting its use.
Game Guard (Unlock) To unlock the Game Guard feature, repeat steps 1 through 3. Enter the same 3 digit code previously used in step 5 with Remote Control Keyboard. LOCK ACTIVATED ENTER CODE TO CHANGE SETTING Enter Same 3 Digit Code Previously Used GAMEGUARD UNLOCKED If 3 Digit Code Is The Same...
Timer Features Sleep Timer- This feature is used for automatic turn off in 30, 60 or 90 minutes. • Sleep Timer NOTE: Display will flash 3, 2 and 1 to indicate the last • Program Timer three remaining minutes prior to turn off. The Recall display will also appear.
Program Timer Program Timer This feature is capable of turning the TV on, tuned to a desired channel and off at a predetermined time (one day or everyday). NOTE: The clock must be set for this feature to operate. ACTION (Refer to the Set-Up Menu to set time.) Press the ACTION button to display the Main Menu.
Set-Up Features Menu The Main Menu can be displayed in two formats. Icon with Text or Icon without Text for those • Menu familiar with the Icon system. • CC (Closed Caption ) on Mute • Set Time Press the ACTION button to display the Main Menu. •...
On Mute Closed Caption with Mute Button Activates the On Screen Closed Captioning when the MUTE button on the Remote Control is pressed. To deactivate press the MUTE button again. NOTE: This feature only functions when the Close Cap- ACTION tion Mode is in the "OFF"...
Set Time- Set Time (Clock) Clock (when set) will display on screen at initial "Turn On", after a channel change and when pressing the RECALL button. The time must be set first in order to operate the Program ON/OFF Timer. Press the ACTION button to display the Main Menu.
Antenna Mode TV or Cable Tuning Mode - The proper Input mode must be selected for the type of signal at the antenna input. • TV mode is used when the Receiver is not connected ACTION to a cable TV system, for example when using a VHF/UHF antenna (channels 02 - 69).
Auto Program Auto Programming - This feature allows you to place all channels with a video signal into Channel Scan Memory. Press the CHANNEL (CH) UP or DOWN button and only those channels with a signal will be ac- cessed. ACTION Press the ACTION button to display the Main Menu.
Manual Programming Manual Program - This feature allows you to select which channels are placed into Channel Scan Memory. Press the CHANNEL (CH) UP or DOWN button and only those channels will be accessed. ACTION Press the ACTION button to display the Main Menu. Press the CH DOWN and VOL RIGHT buttons to select the Set-Up Icon.
Closed Caption Mode Mode This Receiver has a built in decoder that provides a visual depiction of the audio portion of a television program in the form of written words across the screen ACTION (White or Colored letters on a black background). allows the viewer to read the dialogue of a television program or other information.
Channel Caption Channel Caption (Station Identifier) This feature allows you to enter the call names of up to 30 stations into memory (using up to 4 characters for each station). The call name will then display along with the channel number when changing channels or pressing ACTION RECALL.
Audio Mode Selection Stereo/Sap/Mono When Audio is broadcast in Stereo or SAP an ON Screen display will appear on initial "Turn On" and "Channel Change". available choices will be indicated in red. Pressthe ACTION button to displaythe Main Menu. ACTION Press the CH DOWN and VOL RIGHT buttons to select the Audio Icon.
Video Input Video Input - This feature is used to select TV or Video Input. Press the ACTION button to display the Main Menu. Press the VOL RIGHT button to select the Input Icon. ACTION Press the ACTION button to display the Input Select Menu.
Care and Cleaning Picture Tube (Turn set off) Use a mild soap solution or window cleaner and a clean cloth. DO NOT USE ABRASIVE CLEANERS. Avoid excessive moisture and wipe dry. Plastic Cabinets Wipe the cabinet with a soft cloth dampened with water or a mild detergent solution and wipe dry with a soft clean cloth. Avoid excessive moisture.
FEATURE FACTORY PRESET STATE POWER SLEEP TIMER CLOCK NOT SET TIMER Matsushita Electric Panasonic Company Panasonic Company (West) Panasonic Sales Company Division of Matsushita Electric of America of Canada Limited Division of Matsushita Electric 5770 Ambler Drive Corporation of America...