Tyco Electronics 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink Product User Manual
8 port 10/100mbit/s ethernet smart switch with fibre uplink
Hide thumbs
Also See for 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink:
- User manual (60 pages) ,
- Product user manual (18 pages)
Table of Contents
Advertisement
Quick Links
8 Port 10/100Mbit/s Ethernet
Smart Switch with Fibre Uplink
Product User Guide
Introduction
This compact Tyco Electronics/AMPNetconnect auto-negotiating
Ethernet workgroup smart switch enables SOHO users and small
size workgroups to have high speed, low latency LAN connections
to the main network using a fibre link.
The automatic sensing of the connected 10/100Mbit/s data rate
and the detection of either a switch/hub or PC connected to the
Ethernet copper ports eliminates the need for any Ethernet cross-
over cables and greatly simplifies installation.
Package Contents
Unpack the contents and verify them against the items below:-
1. Ethernet switch
2. AC Power cable.
3. Four rubber feet.
4. Console port serial cable
If any item is damaged or missing, please contact your dealer.
-
(EMEA) PL0349 Issue 1
Advertisement
Table of Contents
Related Manuals for Tyco Electronics 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink
Summary of Contents for Tyco Electronics 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink
-
Page 1: Package Contents
Smart Switch with Fibre Uplink Product User Guide Introduction This compact Tyco Electronics/AMPNetconnect auto-negotiating Ethernet workgroup smart switch enables SOHO users and small size workgroups to have high speed, low latency LAN connections to the main network using a fibre link. -
Page 2: Technical Support And Service
If you have a faulty unit then please contact us through the web site to arrange for a replacement unit. The faulty unit must be returned to us as part of the replacement agreement. Page 2 Tyco Electronics... -
Page 3: Front Panel
(ST/SC/MT-RJ) together with singlemode and multimode fibres. Console Port. This port enables the administrator to change switch settings such as port values, VLANs etc. AC Power Connector This connector accepts any standard IEC 320 style power connector. Page 3 Tyco Electronics... -
Page 4: Product Models
1. Fit the self-adhesive rubber feet to the underside of the switch. 2. Locate the switch in a clean, flat and safe position that has easy access to AC power. Ensure that there is sufficient clearance around the switch to enable air circulation. Page 4 Tyco Electronics... - Page 5 RJ-45 ports, then it may be necessary to program the switch to match the speed and duplex modes of the partner devices. See page 9 6. Note that auto-negotiation can take up to 30 seconds to complete depending on the partner device. Page 5 Tyco Electronics...
-
Page 6: Led Indicators
Port transmitting or receiving packets No device is attached or faulty cable Orange The port is in full-duplex mode FDX/COL Blinks Collisions in half-duplex mode The port is in half duplex mode or not connected correctly Page 6 Tyco Electronics... -
Page 7: Configuring The Console Port
Figure 3 - Console Port Settings Connect the PC RS232 serial port to the Console port using the data cable supplied with the switch. Enter any key and the screen should now show the top-level console display. Page 7 Tyco Electronics... - Page 8 To change a port setting, enter port number (1..9) and a new screen is displayed similar to Figure 6 on the next page. Figure 5 – Port Setting Screen - 1 Page 8 Tyco Electronics...
- Page 9 3 to save the setting. Repeat this for all required VLAN and port combinations. Note that the switch resets each time the VLAN state is viewed. This is normal. Figure 8 - VLAN Configuration Page 9 Tyco Electronics...
-
Page 10: Troubleshooting
7. 2. Ensure that the serial data cable supplied with the switch is used. If you still have problems and need further advice, please see Technical Support section on page 2 to obtain more information. Page 10 Tyco Electronics... - Page 11 Average Average Plug-In Fiber Ethernet Average Power Sensitivity Module Type Launch Loss Budget Power dB Multimode Converter (SC) Multimode Converter (ST) Multimode Converter (MT-RJ) Singlemode Converter (SC) Table 2 - Optical Specifications Page 11 Tyco Electronics...
-
Page 12: Product Specifications
0ºC to 45ºC (32ºF to 113ºF) (Operating) Humidity 10% to 90% (Non-condensing) Power IEC 320 Format Main Cord Connection Power Supply 100v to 240v AC, 50/60Hz auto-ranging. Power 21 Watts (Max.) FCC Class A and CE Mark Table 3 - Product Specifications Page 12 Tyco Electronics...
Need help?
Do you have a question about the 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink and is the answer not in the manual?
Questions and answers