Radiator Fan And Air Conditioner (3S-Fe) - Toyota CAMRY SV21 Wiring Diagram

RADIATOR FAN AND AIR CONDITIONER (3S–FE)
SYSTEM OUTLINE
1. RECIRC/FRESH CONTROL SERVO MOTOR OPERATION (FOR PUSH SWITCH TYPE)
(SWITCHING FROM FRESH TO RECIRC)
WITH THE IGNITION SW ON, CURRENT FROM THE GAUGE FUSE FLOWS TO TERMINAL 1 OF THE SERVO MOTOR. WHEN THE
RECIRC SW IS TURNED ON, THE CURRENT FLOWS FROM SERVO MOTOR
CONTROL ASSEMBLY TERMINAL I17
IT IS IN THE RECIRC POSITION, THE CIRCUIT IS CUT INSIDE THE SERVO MOTOR AND THE DAMPER STOPS IN THAT POSITION.
WITH THE CIRCUIT FOR THE INDICATOR LIGHT, CURRENT FLOWS FROM THE GAUGE FUSE
CONTROL ASSEMBLY
WHILE THE RECIRC SW IS ON.
(SWITCHING FROM RECIRC TO FRESH)
WHEN THE IGNITION IS ON AND THE FRESH SW IS TURNED ON, CURRENT FLOWS FROM TERMINAL 3 OF THE SERVO MOTOR
TERMINAL I10 OF THE HEATER CONTROL ASSEMBLY
MOVES TO THE FRESH SIDE. WHEN THE DAMPER IS IN THE FRESH POSITION, THE CIRCUIT IS CUT INSIDE THE SERVO MOTOR
AND THE DAMPER STOPS IN THAT POSITION.
2. OPERATION OF THE AIR VENT MODE CONTROL SERVO MOTOR (FOR PUSH SWITCH TYPE)
(SWITCHING FROM FACE TO BI–LEVEL)
WHEN THE BI–LEVEL SW IS TURNED ON WITH THE DAMPER IN THE FACE POSITION, A SIGNAL THAT THE CIRCUIT IS GROUNDED IS
OUTPUT FROM TERMINAL I12 OF THE HEATER CONTROL ASSEMBLY
THE SYSTEM AMPLIFIER. (AT THIS TIME, THE CURRENT FLOWING THROUGH TERMINAL I7 OF THE HEATER CONTROL ASSEMBLY
FLOWS THROUGH TERMINAL I17
WHEN THE CIRCUIT IS NOT GROUNDED IS INPUT TO TERMINAL D10 OF THE AMPLIFIER. THESE 2 SIGNALS CAUSE THE AMPLIFIER
TO OPERATE AND CURRENT FLOWS FROM TERMINAL D5 OF THE AMPLIFIER
WHICH ROTATES THE SERVO MOTOR, CAUSING THE DAMPER TO MOVE TO THE BI–LEVEL POSITION.
WHEN THE DAMPER COMES TO THE BI–LEVEL POSITION, A SIGNAL THAT THE GROUND CIRCUIT IS CUT IS INPUT TO TERMINAL D11
OF THE AMPLIFIER, AND AMPLIFIER OPERATION CAUSES THE SERVO MOTOR TO STOP ROTATING AND THE DAMPER TO STAY IN
POSITION.
(SWITCHING TO OTHER MODE POSITIONS)
WHEN SWITCHING THE DAMPER FROM FACE TOWARDS DEF, AS EXPLAINED BEFORE, A GROUND SIGNAL IS INPUT TO TERMINAL
D11 OF THE AMPLIFIER AND A NON–GROUND SIGNAL IS INPUT TO TERMINAL D10 SO THAT CURRENT FLOWS FROM TERMINAL D5
SERVO MOTOR TERMINAL D4, MOVING THE DAMPER TO THE DESIRED POSITION.
WHEN SWITCHING THE DAMPER IN THE OPPOSITE DIRECTION FROM DEF TOWARDS FACE, A GROUND SIGNAL IS INPUT TO
TERMINAL D10 OF THE AMPLIFIER AND A NON–GROUND SIGNAL IS INPUT TO TERMINAL D11 SO THAT THE CURRENT FLOWS FROM
TERMINAL D4 SERVO MOTOR
DAMPER TO THE DESIRED POSITION.
3. OPERATION OF THE AIR MIX CONTROL SERVO MOTOR (FOR PUSH SWITCH TYPE)
(SWITCHING FROM WARM TO COOL)
WHEN THE TEMPERATURE CONTROL KNOB IS SWITCHED FROM WARM POSITION TO COOL POSITION, THE RESISTANCE INSIDE
THE HEATER CONTROL ASSEMBLY BECOMES GREATER THAN THE RESISTANCE INSIDE THE SERVO MOTOR. THE SIGNAL AT THIS
TIME IS INPUT TO THE SYSTEM AMPLIFIER, CAUSING THE AMPLIFIER TO OPERATE. CURRENT FLOWS FROM TERMINAL D8 OF THE
AMPLIFIER SERVO MOTOR
RESPECTIVE RESISTANCES ARE THE SAME VALVE, THE SERVO MOTOR STOP.
(SWITCHING FROM COOL TO WARM)
WHEN THE TEMPERATURE CONTROL KNOB IS SWITCHED FROM COOL POSITION TO WARM POSITION, THE RESISTANCE INSIDE
THE HEATER CONTROL ASSEMBLY BECOMES LESS THAN THE RESISTANCE INSIDE THE SERVO MOTOR. THE SIGNAL AT THIS TIME
IS INPUT TO THE SYSTEM AMPLIFIER, CAUSING THE AMPLIFIER TO OPERATE. CURRENT FLOWS FROM TERMINAL D9 OF THE
AMPLIFIER SERVO MOTOR
RESPECTIVE RESISTANCE ARE THE SAME VALVE, THE SERVO MOTOR STOPS.
4. RADIATOR FAN AND CONDENSER FAN OPERATION
WHEN THE IGNITION SW IS TURNED ON, CURRENT FROM THE IGN FUSE FLOWS THROUGH TERMINAL 1 OF THE RADIATOR FAN
RELAY NO. 1 TERMINAL 2
TEMP. SW GROUND, ACTIVATING THE RELAY. AT THIS TIME, CURRENT IS SUPPLIED FROM THE FL 30A RDI FAN TO TERMINAL 4
OF THE RELAY. AT THE SAME TIME, CURRENT FROM THE IGN FUSE FLOWS THROUGH TERMINAL 6 OF THE CONDENSER FAN
RELAY NO. 2 COIL TERMINAL 2
CDS TERMINAL 1 OF THE A/C CONDENSER FAN MOTOR
TERMINAL 2 OF THE RELAY NO. 3.
* LOW SPEED OPERATION
WHEN THE A/C MAGNET CLUTCH IS TURNED ON DURING A/C OPERATION, CURRENT FROM THE A/C FUSE FLOWS THROUGH
TERMINAL 1 OF THE A/C MAGNET CLUTCH RELAY
TERMINAL 3 GROUND, ACTIVATING RELAY NO. 3. THEN THE CURRENT APPLIED TO TERMINAL 2 OF RELAY NO. 3 FLOWS
THROUGH TERMINAL 4
RADIATOR FAN MOTORS ARE CONNECTED IN SERIES, BOTH FANS ROTATE AT LOW SPEED.
158
GROUND, THE MOTOR ROTATES AND THE DAMPER MOVES TO THE RECIRC SIDE. WHEN
INDICATOR LIGHT TERMINAL I17
GROUND, CAUSING THE INDICATOR LIGHT TO LIGHT UP). AT THE SAME TIME, THE SIGNAL FOR
TERMINAL D5, CAUSING THE SERVO MOTOR TO ROTATE IN REVERSE AND MOVING THE
TERMINAL D9 GROUND, CHANGING THE DAMPER FROM WARM TO COOL POSITION. WHEN THE
TERMINAL D8 GROUND, CHANGING THE DAMPER FROM COOL TO WARM POSITION. WHEN THE
TERMINAL 1 OF THE A/C HIGH PRESSURE SW
A/C HIGH PRESSURE SW
TERMINAL 1 OF THE RADIATOR FAN MOTOR
TERMINAL 2
GROUND AND THE INDICATOR LIGHT CONTINUES TO LIGHT UP
TERMINAL I17 GROUND, THE MOTOR ROTATES AND THE DAMPER
TERMINAL 6 OF THE SERVO MOTOR
TERMINAL 2
A/C WATER TEMP. SW
TERMINAL 2 TERMINAL 1 OF THE RELAY NO. 2
TERMINAL 2 TERMINAL 1 OF THE CONDENSER FAN RELAY NO. 3
TERMINAL 2
TERMINAL I2 OF THE HEATER
TERMINAL I7 OF THE HEATER
SERVO MOTOR TERMINAL D4
TERMINAL 1 OF THE A/C WATER
GROUND, THEN THROUGH THE FL 30A
GROUND. SINCE THE CONDENSER AND
TERMINAL D11 OF
GROUND,
TERMINAL 4